Specifications Index
TRIBUTE SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 174-235 Ft. Lbs. (236-319 N.m) | ||
| Rear | 214 Ft. Lbs. (290 N.m) | ||
| Battery | BATTERY LOAD TEST | ||
| Brakes | |||
| Bleeding Sequence | BRAKELINE BLEEDING SEQUENCE | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Drum Brakes | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 13-18 psi | ||
| Thermostat R & I | |||
| 2.0L 4-Cyl. | NA | ||
| 3.0L V6 | THERMOSTAT | ||
| Water Pump R & I | |||
| 2.0L 4-Cyl. | NA | ||
| 3.0L V6 | WATER PUMP | ||
| Engine Mechanical | |||
| 2.0L 4-Cyl. | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | 54-80 psi (370-550 kPa) at 4,000 RPM. | ||
| Overhaul | GENERAL ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.0L V6 | |||
| Compression | ENGINE COMPRESSION | ||
| Oil pressure | 40 psi (276 kPa) at 2,000 RPM. | ||
| Overhaul | ENGINE | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 83 Ft. Lbs. (112 N.m) | ||
| Fuel System | |||
| Pressure Specification (Unregulated - Measured at fuel pump) | 35-55 psi (2.3-3.9 kg/cm2 ) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE (B2300, B3000, B4000 & TRIBUTE) | ||
| Fuel Filter Location | FUEL FILTER LOCATION | ||
| Fuel Filter R & I | REMOVAL & INSTALLATION (TRIBUTE) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.0L 4-Cyl. | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.0L V6 | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | |||
| 2.0L 4-Cyl. | See appropriate graphic under IGNITION WIRE ROUTING . | ||
| 3.0L V6 | NA | ||
| Spark Plug | |||
| 2.0L 4-Cyl. (Motorcraft: Cyl. 1 & 3, AZFS-32F: Cyl, 2 & 4, AZFS-32FE) | |||
| Gap | .051 in. (1.3 mm) | ||
| Torque | 11 Ft. Lbs. (15 N.m) | ||
| 3.0L V6 (Motorcraft AWSF-32F) | |||
| Gap | .052-.056 in. (1.3-1.4 mm) | ||
| Torque | 11 Ft. Lbs. (15 N.m) | ||
| Starting | |||
| Starter | DESCRIPTION & OPERATION | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | SPECIFICATIONS & PROCEDURES | ||
| Torque | SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 98 Ft. Lbs. (133 N.m) | ||