LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2005 >> MPV LX-SV >> Repair and Diagnosis (Single Page) >> Restraints >> Air Bag, SRS >> On-Board Diagnostic (Air Bag System - Two-Step Deployment Control System) >> PID/Data Monitor Table [Two-Step Deployment Control System]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

PID/Data Monitor Table [Two-Step Deployment Control System]

PID/DATA MONITOR (TWO-STEP DEPLOYMENT CONTROL SYSTEM)

PID name (definition) Unit/Condition Operation Condition (Reference) Terminal
CCNT_RCM
(Number of continuous DTCs)		 -
  • DTCs detected: 1-255
  • No DTCs detected: 0
 -
DABAGR
(Driver-side air bag module (inflator No.1) resistance)		 Ohm Under any condition: 1.5-3.7 ohms 1S.1V
DABAGR2
(Driver-side air bag module (inflator No.2) resistance)		 Ohm Under any condition: 1.5-3.7 ohms 1G, 1J
DR_BUKL
(Driver-side buckle switch status)		 Buckled/Unbuckled
  • Driver-side buckle switch on: Buckled
  • Driver-side buckle switch off: Unbuckled
 2T
DR_PTENS
(Driver-side pre-tensioner seat belt resistance)		 Ohm Under any condition: 1.5-3.1 ohms 2P, 2S
DS_AB
(Driver-side side air bag module resistance)		 Ohm Under any condition: 1.4-3.2 ohms 2M, 20
DTC_CLR_ST (1)
(Seat weight sensor status)		 Starting/Normal End/In Process/OCS Fault Fault information cleared at seat weight sensor 11
OCS_CAL_ST (1)
(Seat weight sensor calibration status)		 Starting/Normal End/Commanding/NG (Voltage)/NG (Weight)/Timeout/In Process OCS Fault
  • Seat weight sensor calibration start-up: Starting
  • Seat weight sensor calibration completed normally: Normal End
  • Seat weight sensor calibration command being sent: Commanding
  • Voltage malfunction during seat weight sensor calibration: NG (Voltage)
  • Weight error during seat weight sensor calibration: NG (Weight)
  • Seat weight sensor calibration time limit passed: Timeout
  • Seat weight sensor calibration being processed: In Process
  • Seat weight sensor or seat weight sensor control module malfunction: OCS Fault
 11
OCS_FLT
(Passenger sensing system status)		 MOD_Fail/COMM_Fail/CAL_Fail/SNS_Fail/SNS_Fail_L/SNS_Fail_R/BTS_Fail/No_Fail
  • Seat weight sensor control module malfunction: MOD_Fail
  • Seat weight sensor control module communication error: COMM_Fail
  • Seat weight sensor calibration error: CAL_Fail
  • Seat weight sensor malfunction: SNS_Fail
  • Seat weight sensor (LH) malfunction: SNS_Fail_L
  • Seat weight sensor (RH) malfunction: SNS_FaiL_R
  • Passenger-side front buckle switch malfunction: BTS_Fail
  • Passenger sensing system is normal: No_Fail
 11
OCS_SYS_ST (1)
(Seat weight sensor status)		 Empty/Indeterminate/Small/Large/Invalid Occupant classification status determined by seat weight sensor 11
PABAGR
(Passenger-side air bag module (inflator No.1) resistance)		 Ohm Under any condition: 1.4-2.9 ohms 1M, 1P
P_ABAGR2
(Passenger-side air bag module (inflator No.2) resistance)		 Ohm Under any condition: 1.4-2.9 ohms 1A, 1D
PS_AB
(Passenger-side side air bag module resistance)		 Ohm Under any condition: 1.4-3.2 ohms 2I.2L
PS_BUKL
(Passenger-side buckle switch status)		 Buckled/Unbuckled
  • Passenger-side buckle switch on: Buckled
  • Passenger-side buckle switch off: Unbuckled
 2H
PS_PTENS
(Passenger-side pre-tensioner seat belt resistance)		 Ohm Under any condition: 1.5-3.1 ohms 2G.2J
PS_WEIGHT
(Seat weight sensor measured weight of passenger)		 Kg Display of load (total seated weight) on passenger-side seat 11
PSAB_DepSt
(Passenger air bag module deployment status)		 Inactive/Active
  • Passenger-side air bag module non-operation (non-deployment) status: Inactive
  • Passenger-side air bag module operation (deployment) enabled status: Active
 11
RCM_VOLT
(IG1 voltage)		 V
  • Ignition switch is at ON: B+
  • Other: 0
 1W
TRAK_SW
(Seat track position sensor state)		 Forward/Rearward
  • Front seat front position: Forward
  • Front seat rear position: Rearward
 2W, 2X
(1) Used during Seat weight sensor calibration setting. Not necessary for diagnostic.
scientia non olet · About LEMON Manuals