LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2012 >> 6 s Touring Plus >> Repair and Diagnosis (Single Page) >> Body & Frame >> Door Locks >> On-Board Diagnostic [Advanced Keyless Entry System And Push Button Start System] >> PID/Data Monitor Table [Advanced Keyless Entry And Push Button Start System]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

PID/Data Monitor Table [Advanced Keyless Entry And Push Button Start System]

PID name (definition) Unit/Operation Data contents Inspection item (s) Terminal
BRAKE_SW1
(Brake switch status)
On/Off
  • Brake pedal depressed: On
  • Brake pedal not depressed: Off
Brake switch inspection 3S
BRAKE_SW2(1)
(Brake switch 2 status)
On/Off
  • Brake pedal depressed: On
  • Brake pedal not depressed: Off
Brake switch 2 inspection 3E
BZR_OUT
(Keyless beeper status)
On/Off
  • Keyless beeper sound: On
  • Keyless beeper not sound: Off
Keyless beeper inspection 3K
CLUTCH_SW(2)
(Clutch switch status)
On/Off
  • Clutch pedal pressed: On
  • Clutch pedal released: Off
Clutch switch inspection 3B
IMMOBI(4)
(Immobilizer function present/not present)
On/Off
  • Immobilizer function present: On
  • Immobilizer function not present: Off
Keyless control module inspection -
LOCK_SW_D
(Door lock-link switch status)
Lock/Unlock
  • Driver's door: LOCK: Lock
  • Driver's door: UNLOCK: Unlock
Door lock-link switch inspection 3P
MON_ACC
(ACC relay monitor)
On/Off
  • Switch the ignition to ACC: On
  • Switch the ignition to off: Off
ACC relay inspection 2A
MON_IG1
(IG1 relay monitor)
On/Off
  • Switch the ignition to ON: On
  • Switch the ignition to ACC or off: Off
IG1 relay inspection 2C
MON_IG2
(IG2 relay monitor)
On/Off
  • Switch the ignition to ON: On
  • Switch the ignition to ACC or off: Off
IG2 relay inspection 4X
NUMCARD
(Number of advanced keys)
-
  • Number of programmed advanced keys: 0-6
Keyless control module inspection -
NUMKEY(4)
(Number of key codes)
-
  • Number of programmed key codes: 0-8
Keyless control module inspection -
PUSH_ST1
(Push button start1 status)
On/Off
  • Push button start pressed: On
  • Other than these conditions: Off
Push button start inspection 2J
PUSH_ST2
(Push button start2 status)
On/Off
  • Push button start pressed: On
  • Other than these conditions: Off
Push button start inspection 2K
REQ_SW_L
(Request switch (LF) status)
On/Off
  • Request switch (LF) pressed: On
  • Request switch (LF) released: Off
  • Request switch (LF) inspection
3X
REQ_SW_R
(Request switch (RF) status)
On/Off
  • Request switch (RF) pressed: On
  • Request switch (RF) released: Off
  • Request switch (RF) inspection
3U
REQ_SW_BK On/Off
NOTE:
  • Cannot be used in the inspection, and Off is normally displayed
  • -
-
RLY_ACC
(ACC relay status)
On/Off
  • Switch the ignition to ACC: On
  • Switch the ignition to off: Off
ACC relay inspection 4F
RLY_IG1
  • (IG1 relay status)
On/Off
  • Switch the ignition to ON: On
  • Switch the ignition to ACC or off: Off
IG1 relay inspection 4E
RLY_IG2
  • (IG2 relay status)
On/Off
  • Switch the ignition to ON: On
  • Switch the ignition to ACC or off: Off
IG2 relay inspection 4H
RLY_ST
  • (Starter relay status)
On/Off
  • Switch the ignition to START (STARTER relay on): On
  • Other than these conditions: Off
  • Starter relay inspection
4B
SHIFT_N(2)
  • (Shift lever position)
N/Not_N
  • Shift lever in N range: N
  • Other than these conditions: Not_N
Neutral switch inspection 3T
SHIFT_P(3)
  • (Shift lever position)
P/Not_P
  • Shift lever in P range: P
  • Other than these conditions: Not_P
Selector lever inspection 3M
VPWR1
(Keyless control module power supply voltage1)
V
  • Continuous: Approx. 12 V
Battery inspection 1D
VPWR2
(Keyless control module power supply voltage2)
V
  • Continuous: Approx. 12 V
Battery inspection 1E
VPWR3
(Keyless control module power supply voltage3)
V
  • Continuous: Approx. 12 V
Battery inspection 1B
(1) MZR 2.5 
(2) MTX 
(3) ATX 
(4) With immobilizer system