Using The M-MDS

NOTE:

PIDs for the following parts are not available on this model. Go to the appropriate part inspection page.
- CMP sensor (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION ).
- Main relay (See RELAY INSPECTION ).

Connect the M-MDS to the DLC-2.
Turn the ignition switch to the ON position.
Measure the PID value.
- If PID value is not within the specification, follow the instructions in Action column.
NOTE:
- The PID/DATA MONITOR function monitors the calculated value of the input/output signals in the PCM. Therefore, an output device malfunction is not directly indicated as a malfunction of the monitored value for the output device. If a monitored value of an output device is out of specification, inspect the monitored value of the input device related to the output control.
  
  Fig 1: Identifying DLC-2
- The simulation items that are used in the ENGINE CONTROL SYSTEM OPERATION INSPECTION are as follows.
  - ACCS, ALTF, ARPMDES, EVAPCP, EVAPCV, FAN1, FAN2, FP, IMRC, INJ_1, INJ_2, INJ_3, INJ_4, SEGRP, Test, VT Duty1 wt

Item (definition)

Unit/Condition

Condition/Specification (Reference)

Inspection item(s)

A/CT (Evaporator temperature signal voltage)

Indicates the evaporator temperature

Evaporator temperature sensor

A/CT V (Evaporator temperature signal voltage)

Evaporator temperature sensor is 20 °C {68 °F}: Approx. 2.5 V

Evaporator temperature sensor

AAT (Ambient air temperature)

°C, °F

Indicates the ambient air temperature

IAT sensor

AC_REQ (A/C request signal)

OFF/ON

A/C switch OFF: OFF
A/C switch ON: ON

Perform applicable DTC trouble shooting

ACCS (A/C relay)

OFF/ON

A/C relay is OFF: OFF
A/C relay is ON: ON

A/C relay
The following PIDs
- PCM T, TP1, TP2, MAP, ECT, RPM, CPP/PNP, CPP, VSS

AFR (Target air fuel ratio)

Target air fuel ratio is displayed

A/F sensor

AFR_ACT (Actual air fuel ratio)

Actual air fuel ratio is displayed

A/F sensor

ALTF (Generator field coil control duty value)

Idle, E/L is operating: Duty value increases

Generator
The following PIDs
- MAP, ECT, RPM, VSS, VPWR, ALTT V

ALTTV (Generator output voltage)

Idle (no E/L): Approx. 14 V (This is an internal calculation value and differs from the terminal voltage).

Generator

APP (APP sensor)

Accelerator pedal released: approx. 0 %
Accelerator pedal depressed: approx. 100 %

APP sensor No.1, No.2

APP1 (APP sensor No.1)

Accelerator pedal released: Approx. 32 %
Accelerator pedal depressed: Approx. 78 %

APP sensor No.1

Accelerator pedal released: Approx. 1.6 V
Accelerator pedal depressed: Approx. 3.9 V

APP2 (APP sensor No.2)

Accelerator pedal released: Approx. 20 %
Accelerator pedal depressed: Approx. 67 %

APP sensor No.2

Accelerator pedal released: Approx. 1.0 V
Accelerator pedal depressed: Approx. 3.4 V

ARPMDES (Target engine speed)

RPM

Indicate the target engine speed

The following PIDs
- APP1, APP2, TP1, TP2, MAF, IAT, ECT, RPM, BOO, SCCS, CPP/PNP, CPP, COLP, BARO, VSS, ALTT V

BARO (Barometric pressure)

kPa, Bar, psi

Indicate the BARO

BARO sensor

Switch the ignition to ON (at sea level): approx. 4.1 V

BOO (Brake switch)

OFF/ON

Brake pedal released: OFF
Brake pedal depressed: ON

Brake switch No.1

BRA (Brake pressure applied switch)

OFF/ON

Brake pedal released: ON
Brake pedal depressed: OFF

Brake switch No.2

CATT11_DSD (Estimated catalytic converter temperature)

°C

Indicates the estimated catalytic converter temperature

Perform applicable DTC troubleshooting.

CHRGLP (Generator warning light)

OFF/ON

Switch the ignition to ON: ON
idle (after warm up): OFF

Perform applicable DTC troubleshooting.

COLP (Refrigerant pressure switch middle))

OFF/ON

Refrigerant pressure is more than the specification.: On
Refrigerant pressure is less than the specification.: Off

Refrigerant pressure switch (middle)

CPP⁽²⁾ (Clutch pedal position)

OFF/ON

Clutch pedal depressed: On
Clutch pedal released: Off

CPP switch

CPP/PNP⁽²⁾ (Shift lever position)

OFF/ON

Neutral: On
Other than neutral: Off

Neutral switch

DGP_DIS_1⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

DGP_DIS_2⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

DGP_MAX_DIF⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

DGP_SPD⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

ECT (Engine coolant temperature No.1)

°C, °F

Indicate the ECT (No.1)

ECT sensor No.1

ECT (No.1) is 20 °C {68 °F}: Approx. 3.0 V
ECT (No.1) is 80 °C {176 °F}: Approx. 0.9 V

ECT2 (Engine coolant temperature No.2)

°C, °F

Indicate the ECT (No.2)

ECT sensor No.2

ECT (No.2) is 20 °C {68 °F}: 3.04-3.14 V
ECT (No.2) is 80 °C {176 °F}: 0.76-0.83 V

EQ_RAT11 (Equivalence ratio (lambda))

idle (after warm up): Approx. 1

A/F sensor

EQ_RAT11_DSD (Desired equivalence ratio (lambda))

Indicate the target lambda (Excess air factor = supplied air amount/theoretical air/fuel ratio)

A/F sensor

ETC_ACT Electronic throttle control actual)

Indicate the TP angle

Throttle valve actuator

ETC_DSD (Electronic throttle control desired)

Indicate the target TP angle (percent)

Throttle valve actuator
The following PIDs
- APP1, APP2, TP1, TP2, MAF, IAT, ECT, RPM, BOO, SCCS, CPP/PNP, CPP, COLP, BARO, VSS, ALTT V

Indicate the target TP angle

EVAPCP (Purge solenoid valve duty value)

Switch the ignition to ON: 0 %
idle (after warm up): 0 %

Purge solenoid valve
The following PIDs
- TP1, TP2, MAF, IAT, MAP, ECT, O2S11, O2S12, RPM, BOO, BARO, VPWR

EVAPCV (Evaporative emission canister vent valve)

OFF/ON

Simulation item (EVAPCV) is ON: ON

CV solenoid valve

FAN1 (Cooling fan relay No.1 control signal)

OFF/ON

During test mode
CTP: Off

WOT: On

Cooling fan relay No. 1
The following PIDs
- ECT, COLP

FAN2 (Cooling fan relay No.2 control signal)

OFF/ON

During test mode
CTP: Off

WOT: On

Cooling fan relay No.2
The following PIDs
- ECT, COLP

FCL (Fuel cap warning light)

OFF/ON

Fuel cap warning light not illuminated: OFF
Fuel cap warning light illuminated: ON

Perform applicable DTC troubleshooting.

FLI (Fuel level)

Fuel gauge level F: approx. 100 %
Fuel gauge level E: approx. 0 %

Perform applicable DTC troubleshooting.

FP (Fuel pump relay)

OFF/ON

Switch the ignition to ON: OFF
Cranking: ON
idle (after warm up): ON

Fuel pump relay
The following PIDs

FTP (Fuel tank pressure sensor)

kPa, Bar, psi

Indicate the fuel tank pressure

Fuel tank pressure sensor

Fuel tank pressure is equal to barometric pressure: approx. 2.6 V

FUELPW (Fuel injector duration)

sec

idle (after warm up): Approx. 1.4 ms

Fuel injector
The following PIDs
- APP1, APP2, TP1, TP2, MAF, IAT, MAP, ECT, O2S11, O2S12, RPM, BOO, COLP, BARO, VSS, VPWR

FUELSYS (Fuel system status)

OL/CLV OL Drive/OL Fault/CL_Fault

idle (after warm up): CL

Fuel injector
The following PIDs
- APP1, APP2, TP1, TP2, MAF, IAT, MAP, ECT, O2S11, O2S12, RPM, BOO, COLP, BARO, VSS, VPWR

GEAR⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

HTM_CNT⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

HTM_DIS⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

HTR11 (A/F sensor heater)

OFF/ON

Idle (after warm up): ON

A/F sensor heater
Inspect following PIDs
- TP1, TP2, MAF, IAT, MAP, ECT, RPM, VPWR

HTR12 (HO2S heater control)

OFF/ON

Idle (after warm up): ON

HO2S heater control
The following PIDs
- TP1, TP2, MAF, IAT, MAP, ECT, RPM, VPWR

IAT (Intake air temperature)

°C

Indicate the IAT

IAT sensor

IAT is 20 °C {68 °F}: Approx. 2.2 V
IAT is 30 °C {86 °F}: Approx. 1.8 V

IMRC (Variable tumble control)

OFF/ON

ECT below 60 °C {140 °F} and engine speed below 3,250 rpm: ON
ECT above 60 °C {140 °F} while idling.: OFF

Variable tumble shutter valve actuator
The following PIDs
- APP1, APP2, TP1, TP2, MAF, ECT, RPM

Indicate the variable tumble shutter valve opening ratio

INGEAR (Gears are engaged)

OFF/ON

MTX

When the following conditions are satisfied: ON
- Other than neutral
- Clutch pedal released
Except above: OFF

ATX

R, D, M range: ON
Except above: OFF

MTX

CPP switch
Neutral switch

ATX

TR switch

ISC FBK (ISC feedback value)

ISC feedback value is displayed.

Perform applicable DTC troubleshooting.

ISC_FBK_LRN (ISC feedback learning value)

ISC feedback learning value is displayed.

Perform applicable DTC troubleshooting.

IVS (CTP condition)

Idle/Off Idle

Idle: Idle
Racing: Off Idle

Perform applicable DTC troubleshooting.

KNOCKR (Knocking retard)

Switch the ignition to ON: 0 °
idle (after warm up): 0 °

LINEDES⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

LOAD (Engine load)

idle (after warm up): Approx. 20 %

The following PIDs
- MAP, I AT, MAF, RPM

LONGFT1 (Long term fuel trim (A/F sensor))

idle (after warm up): Approx.-15-15 %

Perform applicable DTC troubleshooting.

LONGFT12 (long term fuel trim (HO2S))

Indicate the fuel learning correction amount (HO2S)

Perform applicable DTC troubleshooting.

LPS⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

MAF (Mass airflow)

g/sec

Indicate the MAF

MAF sensor

Switch the ignition to ON: Approx. 0.65 V
Idle (after warm up): Approx. 1.3 V

MAP (Manifold absolute pressure)

kPa, Bar, psi

Indicate the MAP

MAP sensor

Switch the ignition to ON: Approx. 2.6 V
Idle (after warm up): Approx. 1.3 V

MIL (Malfunction indicator lamp)

OFF/ON

Idle, MIL illuminate: ON
Idle, MIL not illuminate: OFF

Perform applicable DTC troubleshooting.

MIL_DIS (Travelled distance since the MIL illuminated)

km, ft, mi

Indicate the travelled distance since the MIL illuminated

Perform applicable DTC troubleshooting.

O2S11 (A/F sensor)

Idle (after warm up): Approx. 0 mA

A/F sensor

O2S12 (HO2S)

Idle (after warm up): 0-1.0 V

HO2S

OSS⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

PCM_T (PCM temperature sensor)

°C, °F

Indicate the PCM temperature

PCM temperature sensor

PCM_T_MAX Maximum PCM temperature)

°C, °F

Indicate the maximum PCM temperature

RO2FT1 (HO2S fuel trim)

Idle (after warm up): Approx. 0

Perform applicable DTC troubleshooting.

RPM (Engine speed)

RPM

Indicate the engine speed

CKP sensor

SCCS⁽¹⁾ (Cruise control switch)

OFF switch pressed in: approx. 0 V
CANSEL switch pressed in: approx. 1.0 V
SET(-) switch pressed in: approx. 1.8 V
SET(+) switch pressed in: approx. 2.7 V
RESUME switch pressed in: approx. 3.4 V
ON switch pressed in: approx. 4.0 V
Except above: approx. 4.5

Cruise control switch

SEGRP (EGR control)

Switch the ignition to ON: 0
idle (after warm up): 0
Engine speed is 1,187-4,200 rpm: 0-52

EGR valve

SEGRP DSD (Desired EGR valve position)

Indicate the desired EGR valve position

EGR valve
The following PIDs
- TP1, TP2, MAF, IAT, MAP, ECT, RPM, CPP/PNP, CPP, VSS

SHRTFT1 (Short term fuel trim (A/F sensor))

Idle (after warm up):-25-25 %

Perform applicable DTC troubleshooting.

SHRTFT12 (Short term fuel trim (HO2S))

Indicate the fuel feedback correction amount (HO2S)

Perform applicable DTC troubleshooting.

SPARKADV (Ignition timing)

Indicate the ignition timing

Ignition coil
The following PIDs
- APP1, APP2, TP1, TP2, MAF, IAT, ECT, RPM, KNOCKR, BOO, CPP/PNP, CPP

SSA/SS1⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

SSB/SS2⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

SSC/SS3⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

SSD/SS4⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

SSE/SS5⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

TCS⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

Test (Test mode)

OFF/ON

Test mode ON: ON
Test mode OFF: OFF

TFT⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

TFTV⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

THM_1 (Thermostat monitor engine coolant temperature No.1)

°C, °F

Indicates engine coolant temperature No.1 when thermostat monitoring is finished

Thermostat

THM_2 (Thermostat monitor engine coolant temperature No.2)

°C, °F

Indicates engine coolant temperature No.2 when thermostat monitoring is finished

Thermostat

THM_MAX_2 (Thermostat monitor engine coolant temperature No.2 max limit)

°C, °F

Indicates upper limit of engine coolant temperature No.2 for thermostat monitoring execution

Thermostat

THM_MIN_1 (Thermostat monitor engine coolant temperature No.1 min limit)

°C, °F

Indicates lower limit of engine coolant temperature No.1 for thermostat monitoring execution

Thermostat

THM_MIN_2 (Thermostat monitor engine coolant temperature No.2 min limit)

°C, °F

Indicates lower limit of engine coolant temperature No.2 for thermostat monitoring execution

Thermostat

TP REL (Relative throttle position)

Accelerator pedal released: Approx. 12 %
Accelerator pedal depressed: Approx. 81 %

The following PIDs
- TP1, TP2

TP1 (TP sensor No.1)

Accelerator pedal released: Approx. 1.1V
Accelerator pedal depressed: Approx. 4.5 V

TP sensor No. 1

Accelerator pedal released: Approx. 23%
Accelerator pedal depressed: Approx. 91 %

TP2 (TP sensor No.2)

Accelerator pedal released: Approx. 3.9 V
Accelerator pedal depressed: Approx. 0.5 V

TP sensor No.2

Accelerator pedal released: Approx. 22 %
Accelerator pedal depressed: Approx. 91 %

TPCT (TP sensor voltage at CTP)

Switch the ignition to ON: Approx. 0.5 V

TP sensor No. 1, No.2

TR⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

TR_SENS⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

TSS⁽³⁾

(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL] ).

VPWR (Battery positive voltage)

Indicate the battery voltage

Battery

VSS (Vehicle speed)

KPH, MPH

Indicate the vehicle speed

DSC HU/CM

VT ACT1 (Actual valve timing)

idle (after warm up): Approx. 0 °
Racing (after warm up): 0-35 °

CMP sensor

VT DIFF1 (Difference between target valve timing and actual valve timing)

idle (after warm up): approx. 0 °

CMP sensor
The following PIDs
- RPM, LOAD, VT ACT1

VT DUTY1 (OCV control)

idle (after warm up): Approx. 15 %

OCV
The following PIDs
- APP1, APP2, TP1, TP2, MAF, ECT, RPM, CPP/PNR CPR VSS

⁽¹⁾	With cruise control system

⁽²⁾

MTX

⁽³⁾

ATX