Diagnostic Procedure

DIAGNOSTIC PROCEDURE DESCRIPTION

STEP	INSPECTION	RESULTS	ACTION
1	RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION NOTE: Recording can be facilitated using the screen capture function of the PC. Record the FREEZE FRAME DATA/snapshot data on the repair order.	-	Go to the next step.
2	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Verify related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY RELATED PENDING CODE AND/OR DTC Switch the ignition off, then ON (engine off). Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Are any other PENDING CODEs and/or DTCs present?	Yes	Go to the applicable PENDING CODE or DTC inspection. (See DTC TABLE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .)
3		No	Go to the next step.
4	INSPECT MAIN RELAY POWER SUPPLY CIRCUIT FOR SHORT TO GROUND OR OPEN CIRCUIT Switch the ignition off. Remove the main relay. (See RELAY LOCATION .) Measure the voltage at the following terminals (wiring harness-side): Main relay terminal D Main relay terminal A Is the voltage B+?	Yes	Go to the next step.
4		No	Inspect the MAIN 200 A fuse and ENG.MAIN 40 A fuse. If the fuse is blown: Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: MAIN 200 A fuse-Main relay terminal D MAIN 200 A fuse-Main relay terminal A If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to ground. Replace the malfunctioning fuse. If the fuse is damaged: Replace the malfunctioning fuse. If all fuses are normal: Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: Battery positive terminal-Main relay terminal D Battery positive terminal-Main relay terminal A If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has an open circuit. Go to Step 10.
5	INSPECT ENGINE2 15 A FUSE Remove the ENGINE2 15 A fuse. Inspect the ENGINE2 15 A fuse. Is there any malfunction?	Yes	If the fuse is blown: Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: Main relay terminal C-PCM terminal 1CK Main relay terminal C-PCM terminal 2S If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to ground. Replace the fuse. If the fuse is damaged: Replace the fuse. Go to Step 10.
5		No	Reinstall the ENGINE2 15 A fuse, then go to the next step.
6	INSPECT MAIN RELAY CIRCUIT FOR SHORT TO GROUND Main relay is removed. Inspect for continuity between the following terminals (wiring harness-side) and body ground: Main relay terminal C Main relay terminal E Is there continuity?	Yes	Disconnect the PCM connector and inspect the wiring harness for short to ground. If the short to ground circuit could be detected in the wiring harness: Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: Main relay terminal C-PCM terminal 1CK Main relay terminal C-PCM terminal 2S Main relay terminal E-PCM terminal 2K If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to ground. If the short to ground circuit could not be detected in the wiring harness: Replace the PCM (short to ground in the PCM internal circuit). (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Go to Step 10.
6		No	Go to the next step.
7	INSPECT PCM CONNECTOR CONDITION Disconnect the PCM connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 10.
7		No	Go to the next step.
8	INSPECT MAIN RELAY CIRCUIT FOR OPEN CIRCUIT Main relay is removed. Verify that the PCM connector is disconnected. Inspect for continuity between the following terminals (wiring harness-side): Main relay terminal C-PCM terminal 1CK Main relay terminal C-PCM terminal 2S Main relay terminal E- PCM terminal 2K Is there continuity?	Yes	Go to the next step.
8		No	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: Main relay terminal C-PCM terminal 1CK Main relay terminal C-PCM terminal 2S Main relay terminal E-PCM terminal 2K If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has an open circuit. Go to Step 10.
9	INSPECT THROTTLE VALVE ACTUATOR Inspect the throttle valve actuator. (See ENGINE CONTROL SYSTEM OPERATION INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) (See THROTTLE BODY INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Is there any malfunction?	Yes	Inspect the throttle valve actuator related circuits and connectors. If there is any malfunction: Repair or replace the malfunctioning part according to the inspection results. If there is no malfunction: Replace the throttle body. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Go to the next step.
9		No	Go to the next step.
10	VERIFY DTC TROUBLESHOOTING COMPLETED Always reconnect all disconnected connectors. Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Perform the KOEO self test. (See KOEO/KOER SELF TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Is the same DTC present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Go to the next step.
10		No	Go to the next step.
11	VERIFY AFTER REPAIR PROCEDURE Perform the "AFTER REPAIR PROCEDURE". (See AFTER REPAIR PROCEDURE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .)
11		No	DTC troubleshooting completed.