| 1 |
RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
NOTE:
- Recording can be facilitated using the screen capture function of the PC.
- Record the snapshot data on the repair order.
|
- |
Go to the next step. |
| 2 |
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
- Verify related Service Bulletins and/or on-line repair information availability.
- Is any related repair information available?
|
Yes |
Perform repair or diagnosis according to the available repair information.
- If the vehicle is not repaired, go to the next step.
|
| No |
Go to the next step. |
| 3 |
INSPECT LOW FUEL PRESSURE SENSOR/FUEL TEMPERATURE SENSOR CONNECTOR CONDITION
- Switch the ignition off.
- Disconnect the low fuel pressure sensor/fuel temperature sensor connector.
- Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
- Is there any malfunction?
|
Yes |
Repair or replace the connector and/or terminals, then go to Step 9. |
| No |
Go to the next step. |
| 4 |
INSPECT PCM CONNECTOR CONDITION
- Disconnect the PCM connector.
- Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
- Is there any malfunction?
|
Yes |
Repair or replace the connector and/or terminals, then go to Step 9. |
| No |
Go to the next step. |
| 5 |
INSPECT LOW FUEL PRESSURE SENSOR SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY
- Verify that the low fuel pressure sensor/fuel temperature sensor and PCM connectors are disconnected.
- Switch the ignition ON (engine off).
NOTE:
- Another DTC may be stored by the PCM detecting an open circuit.
- Measure the voltage at the low fuel pressure sensor/fuel temperature sensor terminal D (wiring harness-side).
- Is the voltage 0 V?
|
Yes |
Go to the next step. |
| No |
Refer to the wiring diagram and verify whether or not there is a common connector between low fuel pressure sensor/fuel temperature sensor terminal D and PCM terminal 1M.
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has a short to power supply.
Go to Step 9. |
| 6 |
INSPECT LOW FUEL PRESSURE SENSOR POWER SUPPLY CIRCUIT AND SIGNAL CIRCUIT FOR SHORT TO EACH OTHER
- Verify that the low fuel pressure sensor/fuel temperature sensor and PCM connectors are disconnected.
- Switch the ignition off.
- Inspect for continuity between low fuel pressure sensor/fuel temperature sensor terminals A and D (wiring harness-side).
- Is there continuity?
|
Yes |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- Low fuel pressure sensor/fuel temperature sensor terminal A-PCM terminal 1CE
- Low fuel pressure sensor/fuel temperature sensor terminal D-PCM terminal 1M
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has a short to each other.
Go to Step 9. |
| No |
Go to the next step. |
| 7 |
INSPECT LOW FUEL PRESSURE SENSOR CIRCUIT FOR OPEN CIRCUIT
- Verify that the low fuel pressure sensor/fuel temperature sensor and PCM connectors are disconnected.
- Inspect for continuity between the following terminals (wiring harness-side):
- Low fuel pressure sensor/fuel temperature sensor terminal D-PCM terminal 1M
- Low fuel pressure sensor/fuel temperature sensor terminal C-PCM terminal 1CR
- Is there continuity?
|
Yes |
Go to the next step. |
| No |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- Low fuel pressure sensor/fuel temperature sensor terminal D-PCM terminal 1M
- Low fuel pressure sensor/fuel temperature sensor terminal C-PCM terminal 1CR
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has an open circuit.
Go to Step 9. |
| 8 |
INSPECT LOW FUEL PRESSURE SENSOR
|
Yes |
Replace the low fuel pressure sensor/fuel temperature sensor, then go to the next step.
(See LOW FUEL PRESSURE SENSOR/FUEL TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-G 2.5T]
.) |
| No |
Go to the next step. |
| 9 |
VERIFY DTC TROUBLESHOOTING COMPLETED
|
Yes |
Repeat the inspection from Step 1.
Go to the next step. |
| No |
Go to the next step. |
| 10 |
VERIFY AFTER REPAIR PROCEDURE
|
Yes |
Go to the applicable DTC inspection.
(See DTC TABLE [PCM (SKYACTIV-G 2.5T)]
.) |
| No |
DTC troubleshooting completed. |