PID/Data Monitor Table (Start Stop Unit)

-: Not applicable

PID/DATA MONITOR (START STOP UNIT)

PID

Unit/Operation

Data contents

Data read/use method

Module control terminal

BRAKE_SW1

Off/On

Brake switch (No. 1 signal) signal input status

Off: Brake pedal is not depressed.
On: Brake pedal is depressed.

1C (Brake switch)

CLUT_CUT_SW

Off/On

NOTE:

Displays in the M-MDS but it does not operate.

CLUTCH_SW

Off/On

NOTE:

Displays in the M-MDS but it does not operate.

COMM_ST_TSP

Off/On

Displays operation condition of the immobilizer system key code read function

Off: Key code read function not performed
On: Code read function is performed and coil antenna reads key code from remote transmitter transponder.

Key code reading function of immobilizer system is performed and when a brake switch or push button start signal is input, the coil antenna reads the key code from the transponder of the remote transmitter, and displays On while the key code is being sent to the start stop unit.

1AC (PATS+)
1AE (PATS-)

CRU_CON_SW⁽¹⁾

Not_Pressed/On⁽³⁾/Off/MODE⁽²⁾/On/Off/OFF_CANCEL/Cancel/Resume⁽²⁾/Fault/Resume_Plus⁽³⁾/Set (+)⁽²⁾/Set (-)⁽²⁾/Distance (+)⁽²⁾/Distance (-)⁽²⁾

Cruise control switch operation condition

Not_Pressed: Each switch of cruise control switch is not pressed.
On: Cruise ON switch is pressed.
Off: -
MODE: MODE switch is pressed.
Off/On: -
OFF_CANCE L: OFF/CANCEL switch is pressed.
Cancel: -
Resume: RESUME switch is pressed.
Fault: Cruise control switch has a malfunction.
Resume_Plus: RESUME/+ switch is pressed.
Set (+): SET + switch is pressed.
Set (-): SET - switch is pressed.
Distance (+): DISTANCE (+) switch is pressed.
Distance (-): DISTANCE (-) switch is pressed.

1Y (Cruise control switch signal)

ES_UL_SW

Not_Unlock/Unlock

Steering lock unlock switch condition

Off: Steering lock unlock switch is off.
On: Steering lock unlock switch is on.

ES_UL_SW_M

Not_Unlock/Unlock

Memory value of steering lock unlock switch

Off (Lock): Memory value of steering lock unlock switch is not unlocked.
On (Unlock): Memory value of steering lock unlock switch is unlocked.

ES_ULL_SW

Off/On

Steering lock unlock/lock switch condition

Off: Switch the ignition to ACC or ON (engine off or on). (With steering lock released)
On: Door is opened with ignition switched OFF. (with steering wheel locked)

ES_JLL_SW_M

Off/On

Memory value of steering lock unlock/lock switch

Off: Memory value of steering lock unlock/lock switch is off.
On: Memory value of steering lock unlock/lock switch is on.

F_FOG_SW⁽⁴⁾

Off/On

Off: Fog light switch is not in F.FOG position.
On: Fog light switch is in F.FOG position.

H/L_SW_HI

Off/On

Displays dimmer switch position of the light switch that is being input to the start stop unit

Off: Dimmer switch of light switch is not in HI position
On: Dimmer switch of light switch is in HI position

Verify if the monitor value switches when the dimmer switch of the light switch is switched between LO and HI positions. If the dimmer switch operation and monitor values do not match, inspect the light switch.

H/L_SW_LOW

Off/On

Displays dimmer switch position of the light switch that is being input to the start stop unit

Off: Dimmer switch of light switch is not in LO position
On: Dimmer switch of light switch is in LO position

H/L_SW_OFF

Off/On

Headlight light switch (OFF) operation condition

Off: Light switch is not in OFF position.
On: Light switch is in OFF position.

H/L_SW_PASS

Off/On

Headlight switch (PASS) operation condition

Off: Light switch is not in passing position.
On: Light switch is in passing position.

H/L_SW_TNS

Off/On

Headlight switch (TNS (parking lights)) operation condition

Off: Light switch is not in TNS (parking lights) position.
On: Light switch is in TNS (parking lights) position.

HAZARD_SW

Off/On

Displays condition of hazard warning switch input to start stop unit

Off: Hazard warning switch is off.
On: Hazard warning switch is on.

1G (Hazard warning switch signal)

IG_POSITION

OFF/ACC/ON/CRANK

Displays power status controlled by the start stop unit

OFF: Start stop unit controls ignition switch off (lock)
ACC: Start stop unit controls ignition switch ACC
ON: Start stop unit controls ignition switch ON (engine off)
CRANK: Start stop unit controls cranking at ignition switch ON

When the push button start is operated, the start stop unit performs power source switching and displays the PID value of the power source position in which control was performed.
If the push button start operation and PID value do not match, and a power source status of another unit differs from the PID value, inspect the input power source of the other unit because the power source control of the start stop unit is normal.

INFO_SW

Off/SW1_On/SW2_On/SW3_On/Unknown/Invalid

Steering switch operation condition

Off: Steering switch INFO switch is not pressed.
SW1_On: -
SW2_On: -
SW3_On: INFO switch is pressed.
Unknown: Steering switch INFO switch signal is not determined.
Invalid: Steering switch malfunction is received.

Displays INFO switch position of steering switch input to start stop unit. Steering switch signal is input to start stop unit via clock spring.

1AA (Steering switch signal)
1AB (Steering switch ground)

LG/T_LK_SW⁽⁵⁾

Off/On

Request switch (liftgate) operation

Off: Request switch (liftgate) is off.
On: Request switch (liftgate) is on.

2F (LF control unit communication)

LG/T_JNL_SW

Off/On

Liftgate opener switch operation condition

Off: Liftgate opener switch is off.
On: Liftgate opener switch is on.

4K (RBCM)

LL_SW_D_LK

Off/On

Driver's door lock link switch (lock side) operation condition

Off: Front door lock-link switch (LH) is in unlock.
On: Front door lock-link switch (LH) is in lock.

1P (Lock input)

NUM_TRNS MIT

Displays number of the remote transmitters programmed to the start stop unit

P_RANGE_S W

Off/On

Not P position switch condition

Off: NOT P position switch is off.
On: NOT P position switch is on.

1J (P position)

PAD_DOWN_SW

Off/On

NOTE: Displays in the M-MDS but it does not operate.

PAD_UP_SW

Off/On

NOTE: Displays in the M-MDS but it does not operate.

R_FOG_SW

Off/On

NOTE: Displays in the M-MDS but it does not operate.

RELAY_ACC

Off/On

ACC relay operation condition

Off: ACC relay drive is off.
On: ACC relay drive is on.

2C (ACC relay control)

RELAY_IG1

Off/On

IG1 relay operation condition

Off: IG1 relay drive is off.
On: IG1 relay drive is on.

2S (IG1 relay control)

RELAY_IG2

Off/On

IG2 relay operation condition

Off: IG1 relay drive is off.
On: IG2 relay drive is on.

2D (IG2 relay control)

RF_RECEP_ST

Initial/Transmitter/RF_Response

Displays radio reception status from the remote transmitter

Initial: Signal from remote transmitter is not received by start stop unit
Transmitter: Signal by button operation on remote transmitter is received by start stop unit
RF_Response: During remote transmitter authorization, response signal from remote transmitter is received by start stop unit

When verifying the PID value while operating the remote transmitter buttons, if "Transmitter" is displayed it can be determined that the transmission between the remote transmitter, keyless receiver, and start stop unit is normal.

2R (Keyless receiver communication)

RF_TRNS_NUM

Initial/No. 1/No. 2/No. 3/No. 4/No. 5/No. 6

When pressing the unlock button of the remote transmitter, the registration number of the remote transmitter sending radio waves to the start stop unit is displayed.

Initial: Registration number of remote transmitter cannot be received
No. 1: Registration number No. 1 remote transmitter is received
No. 2: Registration number No. 2 remote transmitter is received
No. 3: Registration number No. 3 remote transmitter is received
No. 4: Registration number No. 4 remote transmitter is received
No. 5: Registration number No. 5 remote transmitter is received
No. 6: Registration number No. 6 remote transmitter is received

When DTC B13D3:16 (Low remote transmitter battery voltage) is detected, the registration number of the remote transmitter in which the battery voltage has decreased is displayed in the snapshot data item TRNS_NUM _L. Display the registration number of the remote transmitter using the PID, verify the remote transmitter with the low battery voltage, and inspect the battery condition of the target remote transmitter.

2R (Keyless receiver communication)

RQ_SW_LF⁽⁵⁾

Off/On

Request switch (LF) operation condition

Off: Request switch (LF) is not pressed.
On: Request switch (LF) is pressed.

The signal is input to the start stop unit through the LF control unit of the request switch (LF).

2F (LF control unit communication)

RQ_SW_RF⁽⁵⁾

Off/On

Request switch (RF) operation condition

Off: Request switch (RF) is not pressed.
On: Request switch (RF) is pressed.

The signal is input to the start stop unit through the LF control unit of the request switch (RF).

2F (LF control unit communication)

SECURITY_I

Off/On

Output condition of security indicator

Off: Security indicator light is turned off.
On: Security indicator light is illuminated.

Security indicator on request to instrument cluster

2M (HS-CAN+)
2O (HS-CAN-)

SFT_LK_SOL

Off/On

Shift lock solenoid operation condition

Off: Shift-lock is operated.
On: Shift-lock is released.

2G (Shift lock)

SPD_LIM_SW

Off/On/Unknown

NOTE: Displays in the M-MDS but it does not operate.

SSB_1

Off/On

Push button start switch 1 input signal

Not_Unlock: Push button start switch is off.
Unlock: Push button start switch is on.

1H (Push button start 1)

SSB_2

Off/On

Push button start switch 2 input signal

Not_Unlock: Push button start switch is off.
Unlock: Push button start switch is on.

2J (Push button start 2)

SSB_AMBER

Off/On

Push button start indicator light (amber) illumination request

Off: Push button start indicator light (amber) is turned off.
On: Push button start indicator light (amber) is illuminated.

1M (Push button illumination (amber))

SSB_GREEN

Off/On

Push button start indicator light (green) illumination request

Off: The conditions necessary for engine-start are not met.
On: The conditions necessary for engine-start are met.

1K (Push button illumination (green))

SSB_ILLMI

Off/On

Push button start illumination request

On: Door is opening/closing or headlights are turned on.
Off: Conditions other than above.

1I (Push button illumination)

START_RLY_1

Displays voltage at start stop unit terminal 2V

2V (Starter relay)

START_RLY_2

Displays voltage at start stop unit terminal 1D

1D (Starter monitor)

STR_A_ANG_A⁽⁶⁾

° (deg)

Displays steering angle sensor A signal aiming angle

STR_A_ANG_B⁽⁶⁾

° (deg)

Displays steering angle sensor B signal aiming angle

STR_AB_ANG⁽⁶⁾

° (deg)

Displays steering angle signal (absolute angle)

Steering wheel in neutral position: Near 0 degrees
Steering wheel turned to left: Changes from 0 degrees to positive
Steering wheel turned to right: Changes from 0 degrees to negative

STR_ANG_S

Without/With

Vehicle with/without steering angle sensor

Without: Steering angle sensor is not equipped.
With: Steering angle sensor is equipped.

STR_ANG_S_A⁽⁶⁾

Displays voltage at the steering angle sensor A signal

1U (Steering angle sensor (signal A/D1))

NOTE:

(See STEERING ANGLE SENSOR INSPECTION .)

STR_ANG_S_B⁽⁶⁾

Displays voltage at the steering angle sensor B signal

1W (Steering angle sensor (signal A/D1))

NOTE:

(See STEERING ANGLE SENSOR INSPECTION .)

STR_ANG_S_V⁽⁶⁾

Displays steering angle sensor power supply voltage

NOTE:

"5 V" is displayed even if the voltage is 5 V or more.

1S (Steering angle sensor power supply)

T_SEN_LF

Off/On

NOTE: Displays in the M-MDS but it does not operate.

T_SEN_RF

Off/On

NOTE: Displays in the M-MDS but it does not operate.

TURN_SW_L

Off/On

Turn switch (LH) input

Off: Turn switch is in position other than LH.
On: Turn switch is in LH position.

TURN_SW_R

Off/On

Turn switch (RH) input

Off: Turn switch is in position other than RH.
On: Turn switch is in RH position.

VPWR_ACC

Displays ACC power supply voltage input to start stop unit

If there is a malfunction in the ACC power supply voltage input to the start stop unit, the keyless entry system and push button start system do not operate normally because PID item VPWR_ACC is used for ACC power on/off determination.

1E (ACC monitor)

VPWR_B1

Displays B+ power supply (ROOM fuse) voltage input to start stop unit

If there is a malfunction in the B+ power supply (ROOM fuse) voltage input to the start stop unit, the keyless entry system does not operate normally because PID item VPWR_B1 is used for determining whether or not there is a ROOM fuse inserted.

1A (Power supply)

VPWR_B2

Displays B+ power supply (AT fuse) voltage input to start stop unit

When the ROOM fuse is removed, the B+ power supply (AT fuse) is the start stop unit power supply. If there is a malfunction in the B+ power supply (AT fuse) voltage input to the start stop unit when the ROOM fuse is removed, the push button start system does not operate normally.

2W (Power supply)

VPWR_B3

NOTE: Displays in the M-MDS but it does not operate.

VPWR_IG1

Displays IG1 power supply voltage input to start stop unit

If there is a malfunction in the IG1 power supply voltage input to the start stop unit, the keyless entry system and the push button start system do not operate normally because PID item VPWR_IG1 is used for IG1 power on/off determination.

1B (Power supply)

WASHER_F

Off/On

Windshield washer switch signal input status

Off: Windshield washer switch is in OFF position.
On: Windshield washer switch is in ON position.

WASHER_R

Off/On

Rear washer switch signal input status

Off: Rear washer switch is in OFF position.
On: Rear washer switch is in ON position.

WIP_F_INT

Off/On

Windshield wiper switch (INT) signal input status

Off: Windshield wiper switch is in MIST, OFF or LO position.
On: Windshield wiper switch is in AUTO⁽⁷⁾/INT⁽⁸⁾ or HI position.

WIP_F_LOW

Off/On

Windshield wiper switch (LO) signal input status

Off: Windshield wiper switch is in OFF or AUTO⁽⁷⁾/INT⁽⁸⁾ position.
On: Windshield wiper switch is in MIST, LO or HI position.

WIP_INT_E_A

Low/High

Wiper AUTO/INT volume (encoder) A signal input status

Low: Windshield wiper switch AUTO/INT volume (encoder) A value is low.
High: Windshield wiper switch AUTO/INT volume (encoder) A value is high.

WIP_INT_E_B

Low/High

Wiper AUTO/INT volume (encoder) B signal input status

Low: Windshield wiper switch AUTO/INT volume (encoder) B value is low.
High: Windshield wiper switch AUTO/INT volume (encoder) B value is high.

WIP_INT_E_C

Low/High

Wiper AUTO/INT volume (encoder) C signal input status

Low: Windshield wiper switch AUTO/INT volume (encoder) C value is low.
High: Windshield wiper switch AUTO/INT volume (encoder) C value is high.

WIP_R_INT

Off/On

Rear wiper switch (INT) signal input status

Off: Rear wiper switch is not in INT position.
On: Rear wiper switch is in INT position.

WIP_R_ON

Off/On

Rear wiper switch (ON) signal input status

Off: Rear wiper switch is not in ON position.
On: Rear wiper switch is in ON position.

⁽¹⁾	With cruise control switch

⁽²⁾	With Mazda radar cruise control (MRCC) system

⁽³⁾	Without Mazda radar cruise control (MRCC) system

⁽⁴⁾	With front fog light

⁽⁵⁾	With advanced keyless entry system

⁽⁶⁾	With adaptive front lighting system (AFS) or smart brake support (SBS)

⁽⁷⁾	With auto wiper system

⁽⁸⁾	Without auto wiper system