LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2020 >> CX-3 AWD >> Repair and Diagnosis (Single Page) >> Engine Performance >> System >> On-Board Diagnostic - Engine Control (3 Of 5) >> DTC P061F-00: Internal Control Module Throttle Valve Actuator Controller Performance Problem >> Diagnostic Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Procedure

DTC P061F:00 DIAGNOSTIC PROCEDURE

STEP INSPECTION ACTION
1 RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION 
NOTE:
  • Recording can be facilitated using the screen capture function of the PC.
  • Record the snapshot data on the repair order.
 - Go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Verify related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
 Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY RELATED PENDING CODE AND/OR DTC 
  • Switch the ignition off, then ON (engine off).
  • Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST .)
  • Are any other PENDING CODEs and/or DTCs present?
 Yes Go to the applicable PENDING CODE or DTC inspection.
(See DTC TABLE .)
No Go to the next step.
4 INSPECT START STOP UNIT CONNECTOR CONDITION 
  • Switch the ignition off.
  • Disconnect the start stop unit connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the connector and/or terminals, then go to Step 6.
No Go to the next step.
5 INSPECT PCM CONNECTOR CONDITION 
  • Disconnect the PCM connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the connector and/or terminals, then go to the next step.
No Go to the next step.
6 VERIFY DTC TROUBLESHOOTING COMPLETED 
  • Always reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE .)
  • Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST .)
  • Is the same DTC present?
 Yes Repeat the inspection from Step 1.
Go to the next step.
No Go to the next step.
7 VERIFY AFTER REPAIR PROCEDURE  Yes Go to the applicable DTC inspection. (See DTC TABLE .)
No DTC troubleshooting completed.


DTC P061F:00 DIAGNOSTIC PROCEDURE

STEP INSPECTION RESULTS ACTION
1 RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION 
NOTE:
  • Recording can be facilitated using the screen capture function of the PC.
  • Record the snapshot data on the repair order.
 - Go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Verify related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
 Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY RELATED PENDING CODE AND/OR DTC 
  • Switch the ignition off, then ON (engine off).
  • Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST .)
  • Are any other PENDING CODEs and/or DTCs present?
 Yes Go to the applicable PENDING CODE or DTC inspection.
(See DTC TABLE .)
No Go to the next step.
4 INSPECT START STOP UNIT CONNECTOR CONDITION 
  • Switch the ignition off.
  • Disconnect the start stop unit connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the connector and/or terminals, then go to Step 6.
No Go to the next step.
5 INSPECT PCM CONNECTOR CONDITION 
  • Disconnect the PCM connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the connector and/or terminals, then go to the next step.
No Go to the next step.
6 VERIFY DTC TROUBLESHOOTING COMPLETED 
  • Always reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC .)
  • Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST .)
  • Is the same DTC present?
 Yes Repeat the inspection from Step 1.
Go to the next step.
No Go to the next step.
7 VERIFY AFTER REPAIR PROCEDURE  Yes Go to the applicable DTC inspection. (See DTC TABLE .)
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals