Diagnostic Procedure

DTC P0193:00 (PCM, SKYACTIV-G) DIAGNOSTIC PROCEDURE

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION Record the freeze frame data/snapshot data. NOTE: Recording can be facilitated using the screen capture function of the PC.	-	Go to the next step.
2	VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY Verify related Service Bulletins, on-line repair information, or Service Information availability. Is any related Information available?	Yes	Perform repair or diagnosis according to the available information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	DETERMINE IF FUEL PRESSURE SENSOR OR CONNECTOR CONNECTIONS MALFUNCTION Access the FUEL_PRES PID using the M-MDS. (See PID/DATA MONITOR INSPECTION .) Verify the FUEL_PRES PID value. Is the FUEL_PRES PID value 5 V or B+?	Yes	Go to Step 7.
3		No	Go to the next step.
4	INSPECT FUEL PRESSURE SENSOR CONNECTOR FOR MALFUNCTION Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .) Are the connector and terminal normal?	Yes	Go to the next step.
4		No	Repair or replace the malfunctioning location and perform the repair completion verification.
5	INSPECT PCM CONNECTOR FOR MALFUNCTION Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .) Are the connector and terminal normal?	Yes	Go to the next step.
5		No	Repair or replace the malfunctioning location and perform the repair completion verification.
6	INSPECT FUEL PRESSURE SENSOR FOR MALFUNCTION Inspect the applicable part. (See FUEL PRESSURE SENSOR INSPECTION (VIN M) .) (See FUEL PRESSURE SENSOR INSPECTION (VIN L) .) Is the part normal?	Yes	Go to repair completion verification.
6		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See FUEL INJECTOR REMOVAL/INSTALLATION (VIN M) .) (See FUEL INJECTOR REMOVAL/INSTALLATION (VIN L) .)
7	DETERMINE IF FUEL PRESSURE SENSOR OR WIRING HARNESS MALFUNCTION Switch the ignition off. Disconnect the fuel pressure sensor connector. Access the FUEL_PRES PID using the M-MDS. (See PID/DATA MONITOR INSPECTION .) Verify the FUEL_PRES PID value. Is the FUEL_PRES PID value 5 V or B+?	Yes	Go to the next step.
7		No	Go to Step 9.
8	INSPECT FUEL PRESSURE SENSOR SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect the applicable circuit for open circuit. (See CIRCUIT INSPECTION .) Is the circuit normal?	Yes	Inspect the signal circuit for a short to power supply. (See CIRCUIT INSPECTION .) Repair or replace the malfunctioning location and perform the repair completion verification.
8		No	Repair or replace the malfunctioning location and perform the repair completion verification.
9	INSPECT FUEL PRESSURE SENSOR POWER SUPPLY CIRCUIT AND GROUND CIRCUIT FOR OPEN CIRCUIT Inspect the applicable circuit for open circuit. (See CIRCUIT INSPECTION .) Is the circuit normal?	Yes	Replace the fuel distributor and perform the repair completion verification. (See FUEL INJECTOR REMOVAL/INSTALLATION (VIN M) .) (See FUEL INJECTOR REMOVAL/INSTALLATION (VIN L) .)
9		No	Repair or replace the malfunctioning location and perform the repair completion verification.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Replicate the vehicle conditions at the time the DTC was detected using the following procedure. Perform the KOEO or KOER self test. (See DTC INSPECTION .) Perform the DTC inspection for the PCM. (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .) If the CAN communication is normal, perform the diagnosis from Step 1. If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION (VIN M) .) (See PCM REMOVAL/INSTALLATION (VIN L) .)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTCs DISPLAYED Perform the DTC inspection. (See DTC INSPECTION .) Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.