LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2020 >> CX-30 Select, FWD >> Repair and Diagnosis >> Engine Performance >> System >> On-Board Diagnostic - Engine Control System (3 Of 4) >> DTC P2096-00 Or P2097-00: Ho2S Fuel Injection Control System >> Function Inspection Using M-MDS
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Function Inspection Using M-MDS

DIAGNOSTIC PROCEDURE - FUNCTION INSPECTION USING M-MDS

Step Inspection Results Action
1 PURPOSE: VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY
  • Verify related Service Bulletins, on-line repair information, or Service Information availability.
  • Is any related Information available?
 Yes Perform repair or diagnosis according to the available information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
2 PURPOSE: IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA
  • Is the DTC P2096:00 or P2097:00 on freeze frame data?
 Yes Go to the next step.
No Go to the troubleshooting procedure for DTC on freeze frame data.
(See DTC TABLE (US) .)
3 PURPOSE: RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
  • Record the freeze frame data/snapshot data.
    NOTE:
    • Recording can be facilitated using the screen capture function of the PC.
 - Go to the next step.
4 PURPOSE: VERIFICATION IF MALFUNCTION CAUSED BY LACK OF FUEL
 Yes Refill the fuel.
Go to Troubleshooting Diagnostic Procedure to perform the repair completion verification.
No Go to the next step.
5 PURPOSE: VERIFY DTCs FOR FUEL PRESSURE SENSOR
  • Perform the DTC inspection for the PCM. (See DTC INSPECTION .)
  • Are any of the following DTCs displayed?
    • P0088:00
    • P0192:00
      • P0193:00
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC P0088:00 .)
(See DTC P0192:00 .)
(See DTC P0193:00 .)
Go to the next step.
No Go to the next step.
6 PURPOSE: VERIFY DTCs FOR ELECTRIC VARIABLE VALVE TIMING CONTROL SYSTEM AND HYDRAULIC VARIABLE VALVE TIMING
  • Perform the DTC inspection for the PCM. (See DTC INSPECTION .)
  • Are any of the following DTCs displayed?
    • P0010:00
    • P0011:00
    • P0012:00
    • P0014:00
    • P0015:00
    • P1380:00
    • P2090:00
      • P2091:00
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC P0010:00 .)
(See DTC P0011:00 OR P0012:00 .)
(See DTC P0014:00 [PCM (SKYACTIV-G (VIN M) (US))] .)
(See DTC P0014:00 [PCM (SKYACTIV-G (VIN L) (US))] .)
(See DTC P0015:00 [PCM (SKYACTIV-G (VIN M) (US))] .)
(See DTC P0015:00 [PCM (SKYACTIV-G (VIN L) (US))] .)
(See DTC P1380:00 .)
(See DTC P2090:00 (VIN M) .)
(See DTC P2090:00 (VIN L) .)
(See DTC P2091:00 (VIN M) .)
(See DTC P2091:00 (VIN L) .)
Go to the next step.
No Go to the next step.
7 PURPOSE: VERIFY DTCs FOR MISFIRE
  • Perform the DTC inspection for the PCM. (See DTC INSPECTION .)
  • Are any of the following DTCs displayed?
    • P0300:00
    • P0301:00
    • P0302:00
    • P0303:00
      • P0304:00
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC P0300:00 (US) .)
(See DTC P0301:00, P0302:00, P0303:00 OR P0304:00 (US) .)
Go to the next step.
No Go to the next step.
8 PURPOSE: VERIFY A/F SENSOR AND HO2S INPUT SIGNAL
  • Start the engine and warm it up completely.
  • Access the following PIDs using the M-MDS: (See PID/DATA MONITOR INSPECTION .)
    • A/F_SEN_CUR
      • HO2S_OUT_VOLT
  • Drive the vehicle under the following conditions.
    WARNING:
    • When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID/DATA MONITOR AND RECORD capturing function and inspect later.
    • While performing this step, always operate the vehicle in a safe and lawful manner.
      • After increasing the engine speed to 3, 000 rpm, decelerate using engine braking.
  • Is the displayed PID value as follows?
    • A/F_SEN_CUR: 0.25 mA or more
      • HO2S_OUT_VOLT: 0.3 V or less
 Yes Go to Step 10.
No Go to the next step.
9 PURPOSE: INSPECT RELATED SENSOR WIRING HARNESS AND CONNECTOR
  • Access the following PIDs using the M-MDS: (See PID/DATA MONITOR INSPECTION .)
    • A/F_SEN_CUR
      • HO2S_OUT_VOLT
  • When the PCM, A/F sensor and HO2S are shaken, does the PID value include a PID item which has changed?
 Yes Inspect the related wiring harness and connector.
  • Repair or replace the malfunctioning location.

    Go to Troubleshooting Diagnostic Procedure to perform the repair completion verification.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 1.
10 PURPOSE: VERIFY IF MALFUNCTION CAUSED BY FUEL INJECTOR IMPROPER OPERATION
  • Start the engine and idle it.
  • Access the following simulation items using the M-MDS: (See SIMULATION INSPECTION .)
    • INJ
  • Using the simulation function, can the change in engine speed be verified when operation of each of the fuel injectors is stopped?
 Yes Go to the next step.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 3.
11 PURPOSE: VERIFY IF MALFUNCTION CAUSED BY PURGE SOLENOID VALVE IMPROPER OPERATION
  • Start the engine and idle it.
  • Access the EQUIVALENCE_RATIO_COMD PID and simulation item PRG_DUTY using the M-MDS. (See PID/DATA MONITOR INSPECTION .) (See SIMULATION INSPECTION .)
  • Using the simulation function, does the EQUIVALENCE_RATIO_COMD PID value change when the purge solenoid valve is opened/closed?
 Yes Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 5.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 4.
scientia non olet · About LEMON Manuals