LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2021 >> 6 Signature >> Repair and Diagnosis >> External Pages >> Different car >> Section 99 (On-Board Diagnostic - 360DEGREES View Monitor Control Module) >> DTC Test (360°View Monitor Control Module) >> Snapshot Data
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Snapshot Data

WARNING: This page is about a different car, the 2018 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  • The 360°view monitor control module stores the following two types of snapshot data (vehicle information) when a DTC is detected and displays them in the M-MDS.
    • Vehicle information detected by 360°view monitor control module
    • Vehicle information detected by instrument cluster and received by 360°view monitor control module via CAN communication
  • The data for all DTCs currently detected is stored.

-: Not applicable

Snapshot Data Item Unit Definition Data Read/Use Method Corresponding PID Data Monitor Item
AAT °C °F Ambient temperature - -
APP_STATUS Accelerator Pedal Off/Under20%/Over20%/FAIL Accelerator pedal position status - -
CFG_STATUS Config Complete/Not Configured/Config Error Instrument cluster configuration status - -
ECT_STATUS Under 0 degrees C/0 - Under 80 degrees C/Over 80 degrees C/FAIL Engine coolant temperature status - -
IC_VPWR V Instrument cluster power supply voltage  
  • The 360°view monitor control module constantly receives the power supply voltage value of the instrument cluster sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the 360°view monitor control module records the power supply voltage of the instrument cluster when the DTC was detected, and it is displayed in the M-MDS.
 VPWR (1)
IG-ON_TIMER hh:mm:ss (2) Elapsed time since ignition was switched ON (engine off or on)
NOTE:
  • The instrument cluster records the elapsed time since the ignition was switched ON (engine off or on).
  
  • The 360°view monitor control module constantly receives the elapsed time since the ignition was switched ON (engine off or on) sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the 360°view monitor control module records the elapsed time since the ignition was switched ON (engine off or on) when the DTC was detected, and it is displayed in the M-MDS.
 -
PWR_MODE_K Key Out/Key Recently Out (Position 0)/Accessory (Position 1)/Post Ignition (Position 2)/Ignition On (Position 2)/Running (Position 2)/Running - Starting  
  • Key Out: Ignition switched off
  • Key Recently Out (Position 0): Elapsed time within 3 s since ignition was switched off
  • Accessory (Position 1): Ignition is switched to ACC
  • Post Ignition (Position 2): Elapsed time within 3 s since ignition was switched ON
  • Ignition On (Position 2): Ignition switched ON (engine off)
  • Running (Position 2): Ignition switched ON (engine on)
  • Running - Starting: Cranking condition
  
  • The 360°view monitor control module constantly receives the ignition switch status sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the 360°view monitor control module records the ignition switch status when the DTC was detected, and it is displayed in the M-MDS.
 -
RPM_STATUS Engine Stop/Under1500rpm/Over1500rpm/F AIL Engine speed status  
  • The 360°view monitor control module constantly receives the engine speed sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the 360°view monitor control module records the engine speed when the DTC was detected, and it is displayed in the M-MDS.
 TACHOMTR (1)
SHIFT_STATUS P/N/D/R/FAIL Selector lever position status  
  • The 360°view monitor control module constantly receives the selector lever position sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the 360°view monitor control module records the selector lever position when the DTC was detected, and it is displayed in the M-MDS.
 -
TOTAL_DIST km miles Accumulated total traveled distance from completion of vehicle until 360°view monitor control module detects DTC (Odometer value in instrument cluster) The total traveled distance from which the 360°view monitor control module detects DTCs to the present can be calculated by performing the following procedure.
  1. Verify the odometer value in the instrument cluster.
  2. Verify the snapshot data item TOTAL_DIST.
  3. Subtract 2 from 1.
 -
TOTAL_TIME hh:mm:ss (2) Accumulated total elapsed time since vehicle completion until 360°view monitor control module detects a DTC
NOTE:
  • When the ROOM fuse is removed, and the ignition is switched off, the time is not included in the elapsed time.
 The elapsed time from which the 360°view monitor control module detects DTCs to the present can be calculated by performing the following procedure.
  1. Verify the instrument cluster PID item TOTAL_TIME.
  2. Verify the snapshot data item TOTAL_TIME.
  3. Subtract 2 from 1.
 TOTAL_TIME (1)
VPWR V 360°view monitor control module power supply voltage - VPWR
VSPD_STATUS Stop/0-10km/h/Over10km/h/FAIL Vehicle speed status  
  • The 360°view monitor control module constantly receives the vehicle speed sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the 360°view monitor control module records the vehicle speed when the DTC was detected, and it is displayed in the M-MDS.
 SPEEDOMTR (1)
(1) Instrument cluster PID (See PID/DATA MONITOR TABLE [INSTRUMENT CLUSTER] .)
(2) The seconds may be indicated after the decimal point.
scientia non olet · About LEMON Manuals