Simulation Table

-: Not applicable

SIMULATION PART DESCRIPTION

Simulation item

Unit/Condition

Operation

Operation condition

Engine condition

Other condition

A/C_SW

Off/On

Select Off/On to disengage/engage the magnetic clutch.

Under the following conditions:
- Idle (no load)

Not applicable

AIRSHUT_POS_COMD ⁽²⁾

% Open

Changes % to forcibly open/close the active air shutter.

Not applicable

NOTE:

Override drive parameter: 0-100%

CHARGE_LAMP

No(False)/Yes(True)

Select No/Yes to turn on/off the charging system warning light.
Select No/Yes to display/not display the charging system warning indication on the multi-information display.

Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
  - Racing (not idle)

Not applicable

CSTR_VENT_SOL_DUTY ⁽¹⁾

Changes % and forcibly drives/stops CV solenoid valve.

Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
  - Racing (not idle)

CAUTION:

Do not add fuel with the CV solenoid valve closed. Otherwise, it will result in air pollution because the evaporative gas in the fuel tank will escape directly into the atmosphere.

NOTE:

Override drive parameter: 0%

CV solenoid valve: open
- Override drive parameter: 100%
- CV solenoid valve: close

EGR_COMD

Changes % and forcibly drives/stops EGR valve.

Under the following conditions:
- Idle (no load)

Not applicable

ENG_COOL_VLV_POS_COMD

°(deg)

Displays in the M-MDS but it does not operate.

ENG_RPM_DSD

Rpm

Changes value (RPM) to forcibly vary engine speed.

Under the following conditions:
- Idle
  - Racing (not idle)

The use in the following ranges is recommended:
- Engine coolant temperature: 75-95 °C {167-203 °F}
- Vehicle speed: 0 km/h {0 mph}
  - Override drive parameter input range: 550-2, 000 rpm

EX_SHUT_VLV_DSD

°(deg)

Displays in the M-MDS but it does not operate.

FAN

Changes % and forcibly drives/stops fan control module.

Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
  - Racing (not idle)

NOTE:

Override drive parameter: 0-90%

FP_DUTY

Changes % and forcibly drives/stops fuel pump.

Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
  - Racing (not idle)

WARNING:

Do not use the simulation function while the fuel hose between the high pressure fuel pump and fuel pump is removed.

NOTE:

Override drive parameter: 5-95%

FUEL_PUMP_REQ

Off/On

Select Off/On to forcibly drive/stop the fuel pump.

Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
  - Racing (not idle)

Not applicable

INJ

Forcibly stops the fuel injectors while the engine is idling.

Under the following conditions:
- Idle

WARNING:

Do not use the simulation function while the vehicle is being driven. Stopping the fuel ejection causes the engine to stall which may cause the brakes to not function.

L_SPD_FAN

Off/On

Select Off/On to forcibly drive/stop the cooling fan at low speed.

Not applicable

Not applicable

H_SPD_FAN

Off/On

Select Off/On to forcibly drive/stop the cooling fan at high speed.

Not applicable

Not applicable

MIL

Off/On

Select Off/On to turn on/off the check engine light.

Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
  - Racing (not idle)

Not applicable

OIL_PRES_SOL

Off/On

Select Off/On to forcibly drive/stop the engine oil solenoid valve.

Not applicable

Not applicable

OIL_PUMP_DUTY

% Duty Cycle

Changes % and forcibly drives/stops engine oil solenoid valve.

Under the following conditions:
- Idle

NOTE:

Override drive parameter: 0-100%

PRG_DUTY

Changes % and forcibly drives/stops purge solenoid valve.

Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
  - Racing (not idle)

WARNING:

Do not open the purge solenoid valve while the CV solenoid valve is forcibly closed. Otherwise, there may be abnormal vacuum in the fuel tank, resulting in damage to the fuel tank.

NOTE:

Override drive parameter: 0%

Purge solenoid valve: close
- Override drive parameter: 100%
- Purge solenoid valve: open

WASTEGATE_POS_SIMULATION

Changes % and forcibly drives/stops wastegate valve.

Under the following conditions:
- Idle

Under the following conditions:
- Vehicle speed: 0 km/h {0 mph}
  - Override drive parameter input range: 0-100 %

WHEEL_DRIVE_CTRL_COMD

Forcibly drives/stops AWD solenoid.

Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
  - Racing (not idle)

NOTE:

If the AWD solenoid is forcibly driven, the AWD warning light flashes.

⁽¹⁾	U.S.A. and CANADA

⁽²⁾	Vehicles with active air shutter