LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2022 >> 3 Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Entertainment Systems >> On-Board Diagnostic - Light Control Module >> PID/Data Monitor Table [Light Control Module]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

PID/Data Monitor Table [Light Control Module]

PID/DATA MONITOR DESCRIPTION (LIGHT CONTROL MODULE)

PID Unit/Operation Data contents Module control terminal
B1_CAL_VOLT - Displays correction value based on calibration of +B1 input voltage -
B1_VOLT V Displays voltage at light control module terminal +B1  
B2_CAL_VOLT - Displays correction value based on calibration of +B2 input voltage -
B2_VOLT V Displays voltage at light control module terminal +B2 -
CAL COUNT count Displays number of times calibration is performed -
CAL_CUR_INCLINATION_1 - Displays tilt correction value based on calibration of String-1 (HIGH GND/+LOW and +HIGH, LOW GND and +HIGH) output voltage -
CAL_CUR_INCLINATION_2 - Displays tilt correction value based on calibration of String-2 (+TURN and FAN SIG) output voltage -
CAL_CUR_INTERCEPT_1 mA Displays correction value of section based on calibration of String-1 (HIGH GND/+LOW and +HIGH, LOW GND and +HIGH) output voltage -
CAL_CUR_INTERCEPT_2 mA Displays correction value of section based on calibration of String-2 (+TURN and FAN SIG) output voltage -
FAN_VOLT V Displays voltage at +FAN -
HSS_SW_1_1 Not Equipped/Equipped
  • Not Equipped: HSS switch 1 is not equipped.
  • Equipped: HSS switch 1 is not equipped.
 -
HSS_SW_1_2 Not Equipped/Equipped
  • Not Equipped: HSS switch 2 is not equipped.
  • Equipped: HSS switch 2 is not equipped.
 -
HSS_SW_2_1
NOTE:
  • Displays in the M-MDS but it does not operate.
HSS1_CUR_1 mA Displays current of HSS switch 1 -
HSS1 CUR 2 mA Displays current of HSS switch 2  
HSS1_CUR_3
NOTE:
  • Displays in the M-MDS but it does not operate.
HSS1_STAT_1 OFF/ON
  • OFF: HSS switch 1 is off.
  • ON: HSS switch 1 is on.
 -
HSS1_STAT_2 OFF/ON
  • OFF: HSS switch 2 is off.
  • ON: HSS switch 2 is on.
 -
HSS2_STAT_1
NOTE:
  • Displays in the M-MDS but it does not operate.
IG1_CAL_VOLT - Displays correction value based on calibration of IG1 power supply terminal input voltage -
IG1_STAT OFF/ON
  • OFF: IG1 power supply is not input to light control module.
  • ON: IG1 power supply is input to light control module.
 -
IG1_VOLT V Displays voltage at light control module IG1 power supply terminal -
INSPECTION_DATA Not Complete/Complete
  • Not Complete: Lighting appliance shipment inspection is not completed.
  • Complete: Lighting appliance shipment inspection is completed.
 -
LCM_POS Right/Left
  • Right: Light control module is installed on right.
  • Left: Light control module is installed on left.
 -
LED1_CAL_VOLT_1 - Displays tilt correction value based on calibration of HIGH GND/+LOW and +HIGH output voltage -
LED1_CAL_VOLT_2 - Displays tilt correction value based on calibration of LOW GND and +HIGH output voltage -
LED1_CUR1_DRL mA Displays set current of HIGH GND/+LOW and +HIGH when daytime running light (DRL) is turned on -
LED1_CUR1_FSM mA Displays set current of HIGH GND/+LOW and +HIGH when front side marker light is turned on -
LED1_CUR1_HI mA Displays set current of HIGH GND/+LOW and +HIGH when headlight HI is turned on -
LED1_CUR1_LO mA Displays set current of HIGH GND/+LOW and +HIGH when headlight LO is turned on -
LED1_CUR1_OUTLET1
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_CUR1_OUTLET2
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_CUR1_POS mA Displays set current of HIGH GND/+LOW and +HIGH when TNS (parking lights) is turned on -
LED1_CUR1_TURN mA Displays set current of HIGH GND/+LOW and +HIGH when front turn lights is turned on -
LED1_CUR2_DRL mA Displays set current of LOW GND and +HIGH when daytime running light (DRL) is turned on -
LED1_CUR2_FSM mA Displays set current of LOW GND and +HIGH when front side marker light is turned on -
LED1_CUR2_HI mA Displays set current of LOW GND and +HIGH when headlight HI is turned on -
LED1_CUR2_LO mA Displays set current of LOW GND and +HIGH when headlight LO is turned on -
LED1_CUR2_OUTLET1
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_CUR2_OUTLET2
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_CUR2_POS mA Displays set current of LOW GND and +HIGH when TNS (parking lights) is turned on -
LED1_CUR2_TURN mA Displays set current of LOW GND and +HIGH when front turn lights is turned on -
LED1_DUTY_1 % Displays duty value of HIGH GND/+LOW and +HIGH -
LED1_DUTY_2 % Displays duty value of LOW GND and +HIGH -
LED1_TGT_CUR1_DRL mA Displays target value of HIGH GND/+LOW and +HIGH output current when daytime running light (DRL) is turned on -
LED1_TGT_CUR1_FSM mA Displays target value of HIGH GND/+LOW and +HIGH output current when front side marker light is turned on -
LED1_TGT_CUR1_HI mA Displays target value of HIGH GND/+LOW and +HIGH output current when headlight HI is turned on -
LED1_TGT_CUR1_LO mA Displays target value of HIGH GND/+LOW and +HIGH output current when headlight LO is turned on -
LED1_TGT_CUR1_OUTLET1
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_TGT_CUR1_OUTLET2
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_TGT_CUR1_POS mA Displays target value of HIGH GND/+LOW and +HIGH output current when TNS (parking lights) is turned on -
LED1_TGT_CUR1_TURN mA Displays target value of HIGH GND/+LOW and +HIGH output current when front turn lights is turned on -
LED1_TGT_CUR2_DRL mA Displays target value of LOW GND and +HIGH output current when daytime running light (DRL) is turned on -
LED1_TGT_CUR2_FSM mA Displays target value of LOW GND and +HIGH output current when front side marker light is turned on -
LED1_TGT_CUR2_HI mA Displays target value of LOW GND and +HIGH output current when headlight HI is turned on -
LED1_TGT_CUR2_LO mA Displays target value of LOW GND and +HIGH output current when headlight LO is turned on -
LED1_TGT_CUR2_OUTLET1
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_TGT_CUR2_OUTLET2
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_TGT_CUR2_POS mA Displays target value of LOW GND and +HIGH output current when TNS (parking lights) is turned on -
LED1_TGT_CUR2_TURN mA Displays target value of LOW GND and +HIGH output current when front turn lights is turned on -
LED1_VOLT_1 V Displays voltage at HIGH GND/+LOW and +HIGH -
LED1_VOLT_2 V Displays voltage at LOW GND and +HIGH -
LED2_CAL_VOLT_1   Displays tilt correction value based on calibration of +TURN and FAN SIG output voltage -
LED2_CUR1_DRL mA Displays set current of +TURN and FAN SIG when daytime running light (DRL) is turned on -
LED2_CUR1_FSM mA Displays set current of +TURN and FAN SIG when front side marker light is turned on -
LED2_CUR1_HI mA Displays set current of +TURN and FAN SIG when headlight HI is turned on -
LED2_CUR1_LO mA Displays set current of +TURN and FAN SIG when headlight LO is turned on -
LED2_CUR1_OUTLET1
NOTE:
  • Displays in the M-MDS but it does not operate.
LED2_CUR1_OUTLET2
NOTE:
  • Displays in the M-MDS but it does not operate.
LED2_CUR1_POS mA Displays set current of +TURN and FAN SIG when TNS (parking lights) is turned on -
LED2_CUR1_TURN mA Displays set current of +TURN and FAN SIG when front turn lights is turned on -
LED2_TGT_CUR1_DRL mA Displays target value of +TURN and FAN SIG output current when daytime running light (DRL) is turned on -
LED2_TGT_CUR1_FSM mA Displays target value of +TURN and FAN SIG output current when front side marker light is turned on -
LED2_TGT_CUR1_HI mA Displays target value of +TURN and FAN SIG output current when headlight HI is turned on -
LED2_TGT_CUR1_LO mA Displays target value of +TURN and FAN SIG output current when headlight LO is turned on -
LED2_TGT_CUR1_POS mA Displays target value of +TURN and FAN SIG output current when TNS (parking lights) is turned on -
LED2_TGT_CUR1_TURN mA Displays target value of +TURN and FAN SIG output current when front turn lights is turned on -
LED2_TGT_CUR2_OUTLET1
NOTE:
  • Displays in the M-MDS but it does not operate.
LED2_TGT_CUR2_OUTLET2
NOTE:
  • Displays in the M-MDS but it does not operate.
LED2_VOLT_1 V Displays voltage at +TURN and FAN SIG -
LED3_CAL_VOLT_1   Displays tilt correction value based on calibration of TNS2 GND output voltage -
LED3_CUR1_DRL mA Displays set current of TNS2 GND when daytime running light (DRL) is turned on -
LED3_CUR1_FSM mA Displays set current of TNS2 GND when front side marker light is turned on -
LED3_CUR1_HI mA Displays set current of TNS2 GND when headlight HI is turned on -
LED3_CUR1_LO mA Displays set current of TNS2 GND when headlight LO is turned on -
LED3_CUR1_OUTLET1
NOTE:
  • Displays in the M-MDS but it does not operate.
LED3_CUR1_OUTLET2
NOTE:
  • Displays in the M-MDS but it does not operate.
LED3 CUR1 POS mA Displays set current of TNS2 GND when TNS (parking lights) is turned on  
LED3_CUR1_TURN mA Displays set current of TNS2 GND when front turn lights is turned on -
LED3_DUTY_1 % Displays duty value of TNS2 GND -
LED3_TGT_CUR1_DRL mA Displays target value of TNS2 GND output current when daytime running light (DRL) is turned on -
LED3_TGT_CUR1_FSM mA Displays target value of TNS2 GND output current when front side marker light is turned on -
LED3_TGT_CUR1_HI mA Displays target value of TNS2 GND output current when headlight HI is turned on -
LED3_TGT_CUR1_LO mA Displays target value of TNS2 GND output current when headlight LO is turned on -
LED3_TGT_CUR1_POS mA Displays target value of TNS2 GND output current when TNS (parking lights) is turned on -
LED3_TGT_CUR1_TURN mA Displays target value of TNS2 GND output current when front turn lights is turned on -
LED3_TGT_CUR2_OUTLET1
NOTE:
  • Displays in the M-MDS but it does not operate.
LED3_TGT_CUR2_OUTLET2
NOTE:
  • Displays in the M-MDS but it does not operate.
LED3 VOLT 1 V Displays voltage at TNS2 GND -
LVL_ACTAT_VOLT V Displays voltage at LVL SIG -
LVL_VOLT_RATIO % Displays voltage ratio of LVL SIG -
STRING_CUR_1 mA Displays base current of LOW GND and +HIGH -
STRING_CUR_2 mA Displays base current of +TURN and FAN SIG -
STRING_CUR_3 mA Displays base current of TNS2 GND -
THERMISTOR_VOLT_1 V Displays voltage of TURN GND -
THERMISTOR_VOLT_2 V Displays voltage of THERM -
THERMISTOR_VOLT_INSIDE V Displays voltage of internal thermistor -
scientia non olet · About LEMON Manuals