LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2022 >> CX-30 Select >> Repair and Diagnosis >> Engine Performance >> System >> On-Board Diagnostic - Engine Control System (VIN L) (Introduction) >> Simulation Table
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Simulation Table

- : Not applicable 

SIMULATION PART DESCRIPTION

Simulation item Unit/Condition Definition Operation condition
Engine condition Other condition
A/C_SW Off/On
  • Select Off/On to disengage/engage the magnetic clutch.
  • Ignition is switched ON (engine off)
-
AIRSHUT_POS_COMD (1) % Open
  • Changes % to forcibly open/close the active air shutter.
-
NOTE:
  • Override drive parameter input range: 0-100%
CHARGE_LAMP No (False)/Yes (True)
  • Select No (False)/Yes (True) to turn on/off the charging system warning light.
  • Select No (False)/Yes (True) to display/not display the charging system warning indication on the multi-information display.
  • Ignition is switched ON (engine off)
  • Idle
  • Racing (not idle)
-
CSTR_VENT_SOL_DUTY %
  • Changes % and forcibly drives/stops the CV solenoid valve.
  • Ignition is switched ON (engine off)
  • Idle
  • Racing (not idle)
CAUTION:
  • Do not add fuel with the CV solenoid valve closed.

    Otherwise, it will result in air pollution because the evaporative gas in the fuel tank will escape directly into the atmosphere.

NOTE:
  • Override drive parameter 0%: CV solenoid valve is opened
  • Override drive parameter 100%: CV solenoid valve is closed
  • Override drive parameter input range: 0-100%
EGR_COMD
NOTE:
  • Displays in the M-MDS but it does not operate.
ENG_COOL_VLV_POS_COMD ° (deg)
  • Changes ° (deg) and forcibly drives/stops the coolant control valve.
  • Ignition is switched ON (engine off)
NOTE:
  • Override drive parameter input range: 0-119°
ENG_RPM_DSD Rpm
  • Changes value (Rpm) to forcibly vary the engine speed.
  • Idle
  • Racing (not idle)
NOTE:
  • Override drive parameter input range: 550-2, 000 Rpm
EX_SHUT_VLV_DSD (2) ° (deg)
  • Changes ° (deg) and forcibly drives/stops the exhaust shutter valve.
  • Ignition is switched ON (engine off)
NOTE:
  • Override drive parameter input range: 0-66°
FAN
NOTE:
  • Displays in the M-MDS but it does not operate.
FP_DUTY %
  • Changes % and forciblydrives/stops the fuel pump.
  • Ignition is switched ON (engine off)
  • Idle
  • Racing (not idle)
WARNING:
  • Do not use the simulation function while the fuel hose between the high pressure fuel pump and fuel pump is removed.
NOTE:
  • Override drive parameter input range: 5-95%
FUEL_PUMP_REQ Off/On
  • Select Off/On to forcibly drive/stop the fuel pump.
  • Ignition is switched ON (engine off)
  • Idle
  • Racing (not idle)
-
H_SPD_FAN Off/On
  • Select Off/On to forcibly drive/stop the cooling fan at high speed.
- -
INJ Fuel Injector 1 requested closed/Fuel Injector 2 requested closed/Fuel Injector 3 requested closed/Fuel Injector 4 requested closed/All Fuel Injectors requested closed
  • Forcibly stops the fuel injectors while the engine is idling.
  • Idle
WARNING:
  • Do not use the simulation function while the vehicle is being driven. Stopping the fuel ejection causes the engine to stall which may cause the brakes to not function.
L_SPD_FAN Off/On
  • Select Off/On to forcibly drive/stop the cooling fan at low speed.
- -
MIL Off/On
  • Select Off/On to turn on/off the check engine light.
  • Ignition is switched ON (engine off)
  • Idle
  • Racing (not idle)
-
OIL_PRES_SOL Off/On
  • Select Off/On to forcibly drive/stop the engine oil solenoid valve.
- -
OIL_PUMP_DUTY % Duty Cycle
  • Changes % and forcibly drives/stops the engine oil solenoid valve.
  • Ignition is switched ON (engine off)
  • Idle
NOTE:
  • Override drive parameter input range: 0-100%
PRG_DUTY %
  • Changes % and forcibly drives/stops the purge solenoid valve.
  • Ignition is switched ON (engine off)
  • Idle
NOTE:
  • Override drive parameter 0%: Purge solenoid valve is closed
  • Override drive parameter 100%: Purge solenoid valve is opened
  • Override drive parameter input range: 0-100%
WASTEGATE_POS_SIMULATION
NOTE:
  • Displays in the M-MDS but it does not operate.
WHEEL_DRIVE_CTRL_COMD(3) -
  • Forcibly drives/stops the AWD solenoid built into the coupling component.
  • Ignition is switched ON (engine off)
  • Idle
  • Racing (not idle)
NOTE:
  • If the AWD solenoid is forcibly driven, the AWD warning light flashes.
  • Override drive parameter 1: AWD solenoid is stopped
  • Override drive parameter 2: AWD solenoid is operated
(1) Vehicles with active air shutter

(2) U.S.A. and CANADA

(3) Vehicles with i-ACTIV AWD system