Diagnostic Procedure

DTC B14F3:92 (VEHICLE CONTROL MODULE) DIAGNOSTIC PROCEDURE

Step	Inspection	Results	Action
1	INSPECT VEHICLE CONTROL MODULE (VCM) AND BODY CONTROL MODULE (BCM) FOR MALFUNCTION Perform the DTC inspection for the vehicle control module (VCM) and the body control module (BCM). (See DTC INSPECTION .) Is a DTC related to an internal malfunction displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [VEHICLE CONTROL MODULE (US)] .) (See DTC TABLE [BODY CONTROL MODULE (BCM) (US)] .)
1		No	Go to the next step.
2	INSPECT DRIVER MONITORING CAMERA UNIT FOR MALFUNCTION Perform the DTC inspection for the driver monitoring camera unit. (See DTC INSPECTION .) Is a DTC displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [DRIVER MONITORING CAMERA UNIT (US)] .)
2		No	Go to the next step.
3	VERIFY SCRATCHES OR DIRT ON DRIVER MONITORING CAMERA LENS Verify if there are any scratches or dirt on the driver monitoring camera lens. Are there any scratches or dirt on the driver monitoring camera lens?	Yes	Repair scratches or remove dirt or an obstruction around the driver monitoring camera lens, and perform the repair completion verification.
3		No	Go to the next step.
4	VERIFY IF THERE IS OBSTRUCTION AROUND DRIVER MONITORING CAMERA Verify if there is an obstruction around the driver monitoring camera. Is there an obstruction around the driver monitoring camera?	Yes	Remove the obstruction around the driver monitoring camera and perform the repair completion verification.
4		No	Go to the next step.
5	VERIFY CONDITION AROUND DRIVER MONITORING CAMERA LED Verify if there are any scratches, dirt, or an obstruction around the driver monitoring camera LED. Are there any scratches, dirt, or an obstruction around the driver monitoring camera LED?	Yes	Repair the scratches, or remove the dirt or the obstruction around the driver monitoring camera LED, and perform the repair completion verification.
5		No	Go to the next step.
6	INSPECT DRIVER MONITORING CAMERA UNIT FOR MALFUNCTION DEPENDING ON REPEATABILITY Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)] .) If the CAN communication is normal, replace the driver monitoring camera unit and perform the repair completion verification. (See DRIVER MONITORING CAMERA UNIT REMOVAL/INSTALLATION [(US)] .)
6		No	Go to repair completion verification 2.
7	INSPECT DRIVER MONITORING CAMERA FOR MALFUNCTION DEPENDING ON REPEATABILITY Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)] .) If the CAN communication is normal, replace the center display and perform the repair completion verification. (See CENTER DISPLAY REMOVAL/INSTALLATION .)
7		No	Go to repair completion verification 2.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)] .) If the CAN communication is normal, perform the diagnosis from Step 1. If the malfunction recurs, replace the body control module (BCM), then go to the next step. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION .)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTC IS DISPLAYED Perform the DTC inspection. (See DTC INSPECTION .) Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.