LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2023 >> 3 Select, 4D Hatchback >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> On-Board Diagnostic - Body Control Module (BCM) (4 Of 4) >> PID/Data Monitor Table [Body Control Module (BCM) (Us)]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

PID/Data Monitor Table [Body Control Module (BCM) (Us)]

PID/DATA MONITOR DESCRIPTION - BODY CONTROL MODULE (US)

PID Unit/Operation Data contents Module control terminal
7GTURN_APPLIED_STAT Off/On  
  • Off: Turn light request signal is not received.
  • On: Turn light request signal is received.
 -
ACC_RLY Off/On  
  • Off: ACC relay drive is off.
  • On: ACC relay drive is on.
 -
AGS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: AGS is not equipped.
  • Node Attached and Communicate correctly: AGS is equipped, communication with AGS is normal.
  • Node Attached but Not Communicate correctly: AGS is equipped, but communication with AGS is not normal.
 -
AIR_INTAKE_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Air intake actuator is not equipped.
  • Node Attached and Communicate correctly: Air intake actuator is equipped, communication with air intake actuator is normal.
  • Node Attached but Not Communicate correctly: Air intake actuator is equipped, but communication with air intake actuator is not normal.
 -
ALH_HBC_SW  
NOTE:
  • Displays in the M-MDS but it does not operate.
ALH_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Adaptive front lighting system (AFS) control module is not equipped.
  • Node Attached and Communicate correctly: Adaptive front lighting system (AFS) control module is equipped, communication with adaptive front lighting system (AFS) control module is normal.
  • Node Attached but Not Communicate correctly: Adaptive front lighting system (AFS) control module is equipped, but communication with Adaptive front lighting system (AFS) control module is not normal.
 -
AMB_TEMP °C Displays ambient temperature -
AMP_CAN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Audio amplifier is not equipped.
  • Node Attached and Communicate correctly: Audio amplifier is equipped, CAN communication with audio amplifier is normal.
  • Node Attached but Not Communicate correctly: Audio amplifier is equipped, but CAN communication with audio amplifier is not normal.
 -
AMP_MOST_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Audio amplifier is not equipped.
  • Node Attached and Communicate correctly: Audio amplifier is equipped, MOST communication with audio amplifier is normal.
  • Node Attached but Not Communicate correctly: Audio amplifier is equipped, but MOST communication with audio amplifier is not normal.
 -
ANTI_THEFT_SYS Off/On  
  • OFF: Advanced keyless function is off.
  • ON: Advanced keyless function is on.
 -
APP % Accelerator pedal opening angle (relative value) with the fully released status as 0% and fully depressed status as 100% -
AT_IND_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Shift position indication is not equipped.
  • Node Attached and Communicate correctly: Shift position indication is equipped, communication with shift position indication is normal.
  • Node Attached but Not Communicate correctly: Shift position indication is equipped, but communication with shift position indication is not normal.
 -
AUTO_LGHT_OFF Off/On  
  • Off: TNS (parking lights) or headlight off control by auto light off system is not operated.
  • On: TNS (parking lights) or headlight off control by auto light off system is operated.
 -
BATT_SEN_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
BATT_SOC  
NOTE:
  • Displays in the M-MDS but it does not operate.
BBS_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
BECM_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_ALRM No Request/Request Control  
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
  
BGLR_ALRM_ANS No Request/Request Control  
  • No Request: Hazard warning light flashing answer-back signal is not received.
  • Request Control: Hazard warning light flashing answer-back signal is received.
 -
BGLR_ALRM_REQ No Request/Request  
  • No Request: Body control module (BCM) does not operate theft-deterrent horn and hazard warning lights on.
  • Request Control: Body control module (BCM) operates the theft-deterrent horn and hazard warning lights on.
 -
BGLR_BACKUP_SIREN Off/On  
  • Off: Backup siren setting is not turned on.
  • On: Backup siren setting is turned on.
 3O
BGLR_CHARGE  
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_GAIN  
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_HZRD_REQ Off/Blink 1 time/Blink 2 times/Blink 3 times  
  • Off: Hazard warning lights are not operated to flash.
  • Blink 1 time: Hazard warning lights are operated to flash once.
  • Blink 2 times: Hazard warning lights are operated to flash twice.
  • Blink 3 times: Hazard warning lights are operated to flash three times.
 -
BGLR_IMS  
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_IS_COMD  
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_SEN Off/On  
  • Off: Intruder sensor setting is not turned on.
  • On: Intruder sensor setting is turned on.
 3O
BGLR_SIREN_COMD  
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_SIREN_MODE  
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_STAT DEAD/INITIAL/PRE-ARMING/ARMING/ARMING STAND BY/ALARM/ALARM STAND BY  
  • DEAD: Ignition is in ACC or ON (engine off) and alarm cannot be activated.
  • INITIAL: Ignition is switched OFF and transition to arming stand-by status is possible.
  • PRE-ARMING: Transition period to arming status.
  • ARMING: Alarm can be activated by inputting alarm trigger.
  • ARMING STAND BY: Liftgate is open under arming status.
  • ALARM: Alarm trigger is input and alarm is activated.
  • ALARM STAND BY: After alarm activation finished, standing by for next alarm trigger input.
 -
BGLR_SLEEP_MODE  
NOTE:
  • Displays in the M-MDS but it does not operate.
B-ISG_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
BRK_SW Not Stepping/Stepping  
  • Not Stepping: Brake pedal is not depressed.
  • Stepping: Brake pedal is depressed.
 -
BRK_SW_1 Off/On  
  • Off: Brake switch (No. 1 signal) is off.
  • On: Brake switch (No. 1 signal) is on.
 -
C_DOOR_LCK_SW_D Neutral/Lock/Unlock  
  • Neutral: Door lock switch (driver's side) is neither locked nor unlocked.
  • Lock: Door lock switch (driver's side) is in lock.
  • Unlock: Door lock switch (driver's side) is in unlock.
 -
C_DOOR_LCK_SW_P Neutral/Lock/Unlock  
  • Neutral: Door lock switch (passenger's side) is neither locked nor unlocked.
  • Lock: Door lock switch (passenger's side) is in lock.
  • Unlock: Door lock switch (passenger's side) is in unlock.
 -
CBCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Body control module (BCM) is not equipped.
  • Node Attached and Communicate correctly: Body control module (BCM) is equipped, communication with body control module (BCM) is normal.
  • Node Attached but Not Communicate correctly: Body control module (BCM) is equipped, but communication with body control module (BCM) is not normal.
 -
CENTER_DISP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Center display is not equipped.
  • Node Attached and Communicate correctly: Center display is equipped, communication with center display is normal.
  • Node Attached but Not Communicate correctly: Center display is equipped, but communication with center display is not normal.
 -
CLTCH_INH_SW Off/On  
  • Off: Starter interlock switch is off.
  • On: Starter interlock switch is on.
 -
CMU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Connectivity master unit (CMU) is not equipped.
  • Node Attached and Communicate correctly: Connectivity master unit (CMU) is equipped, communication with connectivity master unit (CMU) is normal.
  • Node Attached but Not Communicate correctly: Connectivity master unit (CMU) is equipped, but communication with connectivity master unit (CMU) is not normal.
 -
COMMANDER_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Commander switch is not equipped.
  • Node Attached and Communicate correctly: Commander switch is equipped, communication with commander switch is normal.
  • Node Attached but Not Communicate correctly: Commander switch is equipped, but communication with commander switch is not normal.
 -
CRASH_SIG Off/On  
  • Off: Crash signal is not received.
  • On: Crash signal is received.
 2J, 2L
Dash-ESU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Dash-electrical supply unit is not equipped.
  • Node Attached and Communicate correctly: Dash-electrical supply unit is equipped, dash-electrical supply unit is normal.
  • Node Attached but Not Communicate correctly: Dash-electrical supply unit is equipped, but communication with dash-electrical supply unit is not normal.
 -
DCDC_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
DCDC_PCM_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
DOOR_LCK_ALL Off/On  
  • Off: All door lock signal is not sent from body control module (BCM).
  • On: All door lock signal is sent from body control module (BCM).
 2J, 2L
DOOR_LCK_ID_CREATE Off/On Displays door lock control ID creation status. -
DOOR_SECURITY Off/On Displays door lock control security condition. -
DOOR_SW_ALL Close/Open  
  • Close: All doors are closed.
  • Open: Any door is open.
 -
DOOR_SW_D Close/Open  
  • Close: Front door (driver's side) is closed.
  • Open: Front door (driver's side) is open.
 2J, 2L
DOOR_SW_L/R Close/Open  
  • Close: Rear door (LH) is closed.
  • Open: Rear door (LH) is open.
 2J, 2L
DOOR_SW_P Close/Open  
  • Close: Front door (passenger's side) is closed.
  • Open: Front door (passenger's side) is open.
 2J, 2L
DOOR_SW_R/R Close/Open  
  • Close: Rear door (RH) is closed.
  • Open: Rear door (RH) is open.
 2J, 2L
DOOR_ULCK_ALL Off/On  
  • Off: All door unlock signal is not sent from body control module (BCM).
  • On: All door unlock signal is sent from body control module (BCM).
 2J, 2L
DOOR_ULCK_D Off/On  
  • Off: Front door (driver's side) unlock request signal is not sent from body control module (BCM).
  • On: Front door (driver's side) unlock request signal is sent from body control module (BCM).
 2J, 2L
Door_ESU_D_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Door-electrical supply unit (driver's side) is not equipped.
  • Node Attached and Communicate correctly: Door-electrical supply unit (driver's side) is equipped, communication with door-electrical supply unit (driver's side) is normal.
  • Node Attached but Not Communicate correctly: Door-electrical supply unit (driver's side) is equipped, but communication with door-electrical supply unit (driver's side) is not normal.
 -
Door_ESU_P_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Door-electrical supply unit (passenger's side) is not equipped.
  • Node Attached and Communicate correctly: Door-electrical supply unit (passenger's side) is equipped, communication with door-electrical supply unit (passenger's side) is normal.
  • Node Attached but Not Communicate correctly: Door-electrical supply unit (passenger's side) is equipped, but communication with door-electrical supply unit (passenger's side) is not normal.
 -
DRL  
NOTE:
  • Displays in the M-MDS but it does not operate.
DRL_REQ Off/On  
  • Off: Body control module (BCM) does not operate daytime running light (DRL) on.
  • On: Body control module (FBCM) operates the daytime running light (DRL) on.
 -
DSC_PT_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: DSC HU/Control Module is not equipped.
  • Node Attached and Communicate correctly: DSC HU/Control Module is equipped, communication via CAN BUS No. 2 with DSC HU/Control Module is normal.
  • Node Attached but Not Communicate correctly: DSC HU/Control Module is equipped, but communication via CAN BUS No. 2 with DSC HU/Control Module is not normal.
 -
DSC_VEH_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: DSC HU/Control Module is not equipped.
  • Node Attached and Communicate correctly: DSC HU/Control Module is equipped, communication via CAN BUS No. 1 with DSC HU/Control Module is normal.
  • Node Attached but Not Communicate correctly: DSC HU/Control Module is equipped, but communication via CAN BUS No. 1 with DSC HU/Control Module is not normal.
 -
DSM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Position memory control module is not equipped.
  • Node Attached and Communicate correctly: Position memory control module is equipped, communication via CAN BUS No. 1 with position memory control module is normal.
  • Node Attached but Not Communicate correctly: Position memory control module is equipped, but communication via CAN BUS No. 1 with position memory control module is not normal.
 -
DVD_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
ENG_RPM_VSPD_RATIO Rpm/Kph Displays engine speed -
ENG_STARTER_VOLT_1 V Displays voltage at body control module (BCM) terminal 2T 2T
ENG_STARTER_VOLT_2 V Displays voltage at body control module (BCM) terminal 2AD 2AD
ENG_STAT Off/Ready/Cranking/Running/Stalled/Afterrun/Shutdown/Not defined Displays engine condition -
EPS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: EPS control module is not equipped.
  • Node Attached and Communicate correctly: EPS control module is equipped, communication with EPS control module is normal.
  • Node Attached but Not Communicate correctly: EPS control module is equipped, but communication with EPS control module is not normal.
 -
ESS_HZRD  
NOTE:
  • Displays in the M-MDS but it does not operate.
ESU_CAN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Electrical supply unit (ESU) is not equipped.
  • Node Attached and Communicate correctly: Electrical supply unit (ESU) is equipped, CAN communication with electrical supply unit (ESU) is normal.
  • Node Attached but Not Communicate correctly: Electrical supply unit (ESU) is equipped, but CAN communication with electrical supply unit (ESU) is not normal.
 -
ESU_LIN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Electrical supply unit (ESU) is not equipped.
  • Node Attached and Communicate correctly: Electrical supply unit (ESU) is equipped, LIN communication with electrical supply unit (ESU) is normal.
  • Node Attached but Not Communicate correctly: Electrical supply unit (ESU) is equipped, but LIN communication with electrical supply unit (ESU) is not normal.
 -
EXT_T/LGT_REL_SW Off/On  
  • Off: Trunk lid opener switch (exterior) (4SD)/liftgate opener switch (5HB) is not pressed.
  • On: Trunk lid opener switch (exterior) (4SD)/liftgate opener switch (5HB) is pressed.
 4J
F_WASH_CTRL_ALLW Wash_Allowed/Not_Allowed  
  • Wash_Allowed: Use of windshield washer is permitted.
  • Not_Allowed: Use of windshield washer is not permitted.
 -
F_WASH_SW Off/On  
  • Off: Windshield washer switch is off.
  • On: Windshield washer switch is on.
 -
F_WIP OFF/Front Wiper On Lo/Front Wiper On Hi/Front Wiper INT Auto On  
  • OFF: Windshield wiper switch is in the OFF position.
  • Front Wiper On Lo: Windshield wiper switch is in the LO position.
  • Front Wiper On Hi: Windshield wiper switch is in the HI position.
  • Front Wiper INT Auto On: Windshield wiper switch is in the INT position.
 -
F_WIP_ANG_SEN_FAIL Not_Failure/Failure  
  • Not_Failure: Position sensor in the windshield wiper motor is normal.
  • Failure: Position sensor in the windshield wiper motor has a malfunction.
 -
F_WIP_CTRL F. Wiper Off/F. Wiper Lo/F. Wiper Hi  
  • F. Wiper Off: Windshield wipers are not operated.
  • F. Wiper Lo: Windshield wipers are operated at low speed.
  • F. Wiper Hi: Windshield wipers are operated at high speed.
 -
F_WIP_FET_FAIL Not_Failure/Failure  
  • Not_Failure: FET circuit is normal.
  • Failure: FET circuit has a malfunction.
 -
F_WIP_INT_VOL % Displays windshield wiper INT level signal value received -
F_WIP_POS Unknown/Parking_Position/Not_Parking_Position  
  • Unknown: Windshield wipers position is not determined.
  • Parking_Position: Windshield wipers in park position.
  • Not_Parking_Position: Windshield wipers in position other than park.
 -
F_WIP_REG_FAIL Not_Failure/Failure  
  • Not_Failure: Windshield wiper regulator is normal.
  • Failure: Windshield wiper regulator is not normal.
 -
F_WIP_REQ OFF/Stop (Parking Position)/F. Wiper Lo/F. Wiper Hi/Stop (Service Position)/Stop (Current Position)  
  • Off: Body control module (BCM) does not operate windshield wipers.
  • Stop (Parking Position): Body control module (BCM) operates windshield wipers to the park position.
  • F. Wiper Lo: Body control module (BCM) operates windshield wipers at low speed.
  • F. Wiper Hi: Body control module (BCM) operates windshield wipers at high speed.
  • Stop (Service Position): Body control module (BCM) operates windshield wipers to the service position.
  • Stop (Current Position): Body control module (BCM) operates windshield wipers to the current position.
 -
F_WIP_ROT_FAIL Not_Failure/Failure  
  • Not_Failure: Windshield wiper rotation direction is normal.
  • Failure: Windshield wiper rotation direction is not normal.
 -
F_WIP_TEACH_STAT_SUB No_Sub_Status/Detect_jig_out_of_area/Unusually_Mode_Switch/Data Flash_Failure/FrontWipr_Failure/Not_detect_jig  
  • No_Sub_Status: Body control module (BCM) cannot receive any signal from windshield wiper arm and blade.
  • Detect_jig_out_of_area: Windshield wiper arm and blade movement is detected to be outside of specified range.
  • Unusually_Mode_Switch: Windshield wiper and washer switch is not normal.
  • Data Flash_Failure: Data is not normal.
  • Front Wipr_Failure: Windshield wipers are malfunctioning.
 -
F_WIP_THRM_FAIL Not_Failure/Failure  
  • Not_Failure: Circuit detecting windshield wiper motor temperature is normal.
  • Failure: Circuit detecting windshield wiper motor temperature is not normal.
 -
F_WIP_TIME_FAIL Not_Failure/Failure  
  • Not_Failure: Windshield wiper is operating normally.
  • Failure: Windshield wiper operating speed is extremely slow (when the Windshield wiper is operating).
 -
F_WIP_VOLT_FAIL Not_Failure/Failure  
  • Not_Failure: Circuit detecting windshield wiper motor voltage is normal.
  • Failure: Circuit detecting windshield wiper motor voltage is not normal.
 -
FR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Front radar sensor is not equipped.
  • Node Attached and Communicate correctly: Front radar sensor is equipped, communication with front radar sensor is normal.
  • Node Attached but Not Communicate correctly: Front radar sensor is equipped, but communication with front radar sensor is not normal.
 -
FSC_LGHT_REQ Off/On  
  • Off: Headlight HI is turned on.
  • On: Headlight HI is turned off.
 -
FSC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Forward sensing camera (FSC) is not equipped.
  • Node Attached and Communicate correctly: Forward sensing camera (FSC) is equipped, communication with forward sensing camera (FSC) is normal.
  • Node Attached but Not Communicate correctly: Forward sensing camera (FSC) is equipped, but communication with forward sensing camera (FSC) is not normal.
 -
FSM_REQ Off/On  
  • Off: TNS (parking lights) signal is not sent from body control module (BCM).
  • On: TNS (parking lights) signal is sent from body control module (BCM).
 -
FSRL_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Front side radar sensor (LH) is not equipped.
  • Node Attached and Communicate correctly: Front side radar sensor (LH) is equipped, communication with front side radar sensor (LH) is normal.
  • Node Attached but Not Communicate correctly: Front side radar sensor (LH) is equipped, but communication with front side radar sensor (LH) is not normal.
 -
FSRR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Front side radar sensor (RH) is not equipped.
  • Node Attached and Communicate correctly: Front side radar sensor (RH) is equipped, communication with front side radar sensor (RH) is normal.
  • Node Attached but Not Communicate correctly: Front side radar sensor (RH) is equipped, but communication with front side radar sensor (RH) is not normal.
 -
FUEL_AMOUNT L Displays fuel level detected by the fuel gauge 2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
FUEL_GAUGE_RES_MAIN Ohm Displays fuel gauge sender unit resistance value 2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
FUEL_GAUGE_RES_SUB  
NOTE:
  • Displays in the M-MDS but it does not operate.
FUEL_GAUGE_VOLT_MAIN V Displays fuel gauge sender unit voltage value 2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
FUEL_GAUGE_VOLT_SUB  
NOTE:
  • Displays in the M-MDS but it does not operate.
GLOBAL_REAL_TIME min Displays cumulative elapsed time since vehicle completion -
GLOWPLUG_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
H/L_CLEAN_RLY  
NOTE:
  • Displays in the M-MDS but it does not operate.
H/L_HI Off/On  
  • Off: Headlight HI signal is not sent from body control module (BCM).
  • On: Headlight HI signal is sent from body control module (BCM).
 -
H/L_HI_SW Off/On  
  • Off: Light switch HI signal is not received.
  • On: Light switch HI signal is received.
 -
H/L_LO_REQ Off/On  
  • Off: Body control module (BCM) does not operate the headlight LO off.
  • On: Body control module (BCM) does not operate the headlight LO on.
 -
H/L_LO_SW Off/On  
  • Off: Other than light switch LO position of light switch is received.
  • On: Light switch LO position of light switch is received.
 -
H/L_LVL_CSTMZ  
NOTE:
  • Displays in the M-MDS but it does not operate.
H/L_OFF_SW Off/On  
  • Off: Light switch OFF signal is not received.
  • On: Light switch OFF signal is received.
 -
H/L_PASSING_SW Off/On  
  • Off: Light switch FLASH-TO-PASS signal is not received.
  • On: Light switch FLASH-TO-PASS signal is received.
 -
HOOD_SW Close/Open  
  • Close: Hood is closed.
  • Open: Hood is open.
 2S
HUD_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Active driving display is not equipped.
  • Node Attached and Communicate correctly: Active driving display is equipped, communication with active driving display is normal.
  • Node Attached but Not Communicate correctly: Active driving display is equipped, but communication with active driving display is not normal.
 -
HZRD_REQ No Request/Request Control  
  • No Request: Body control module (BCM) does not operate the hazard warning light on.
  • Request Control: Body control module (BCM) operates the hazard warning light on.
 -
HZRD_SW OFF/On/Unknown  
  • Off: Hazard warning switch is not pressed.
  • On: Hazard warning switch is pressed.
  • Unknown: Hazard warning switch on/off is not determined.
 -
ICM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Instrument cluster is not equipped.
  • Node Attached and Communicate correctly: Instrument cluster is equipped, communication with instrument cluster is normal.
  • Node Attached but Not Communicate correctly: Instrument cluster is equipped, but communication with instrument cluster is not normal.
 -
IG_ON_TIMER min Time since engine start -
IG1_RLY Off/On  
  • Off: IG1 relay drive is off.
  • On: IG1 relay drive is on.
 -
IMMOBI_IDENTIFY  
NOTE:
  • Displays in the M-MDS but it does not operate.
IMMOBI_OPERAT_MODE Operation Mode 1/Operation Mode 2/Operation Mode 3/Operation Mode 4/Operation Mode 5/Operation Mode 6/Operation Mode 7 Displays immobilizer system operation mode -
IMS_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
IND_ASSY_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Indicator unit is not equipped.
  • Node Attached and Communicate correctly: Indicator unit is equipped, communication with indicator unit is normal.
  • Node Attached but Not Communicate correctly: Indicator unit is equipped, but communication with indicator unit is not normal.
 -
IP-ESU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Climate control unit is not equipped.
  • Node Attached and Communicate correctly: Climate control unit is equipped, communication with climate control unit is normal.
  • Node Attached but Not Communicate correctly: Climate control unit is equipped, but communication with climate control unit is not normal.
 -
KEY_ANS_REQ No Request/Request Control  
  • No Request: Hazard warning light flashing answer-back signal is not received.
  • Request Control: Hazard warning light flashing answer-back signal is received.
 -
KEY_BUZZER Off/On  
  • Off: Keyless beeper is not operated to sound.
  • On: Keyless beeper is operated to sound.
 2AA, 2AB
KEY_ENA Disabled/Enabled  
  • Disabled: Immobilizer system is disabled.
  • Enabled: Immobilizer system is enabled.
 -
LATCH_IP_SW Off/On  
  • Off: Trunk lid opener switch (interior) is not pressed.
  • On: Trunk lid opener switch (interior) is pressed.
 -
LCML_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Light control module (LH) is not equipped.
  • Node Attached and Communicate correctly: Light control module (LH) is equipped, communication with light control module (LH) is normal.
  • Node Attached but Not Communicate correctly: Light control module (LH) is equipped, but communication with light control module (LH) is not normal.
 -
LCMR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Light control module (RH) is not equipped.
  • Node Attached and Communicate correctly: Light control module (RH) is equipped, communication with light control module (RH) is normal.
  • Node Attached but Not Communicate correctly: Light control module (RH) is equipped, but communication with light control module (RH) is not normal.
 -
LFU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: LF control unit is not equipped.
  • Node Attached and Communicate correctly: LF control unit is equipped, communication with LF control unit is normal.
  • Node Attached but Not Communicate correctly: LF control unit is equipped, but communication with LF control unit is not normal.
 -
LLINK_SW_D Unlock/Neutral/Lock/Failure  
  • Unlock: Front door lock-link switch (driver's side) is in unlock.
  • Neutral: Front door lock-link switch (driver's side) is not in lock and unlock.
  • Lock: Front door lock-link switch (driver's side) is in lock.
  • Failure: Front door lock-link switch (driver's side) has a malfunction.
 -
LLINK_SW_P Unlock/Lock  
  • Unlock: Front door lock-link switch (passenger's side) is in unlock.
  • Lock: Front door lock-link switch (passenger's side) is in lock.
 -
LLINK_SW_R Unlock/Lock  
  • Unlock: Rear door lock-link switch (LH), rear door lock-link switch (RH) are in unlock.
  • Lock: Rear door lock-link switch (LH), rear door lock-link switch (RH) are in lock.
 4F
LLINK_SW_STAT_R Off/On  
  • Off: Front door lock-link switch (LH) is in unlock.
  • On: Front door lock-link switch (LH) is in lock.
 -
MASTER_KEY No/Yes  
  • No: There is no master key.
  • Yes: There is master key.
 -
MODE_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Airflow mode actuator is not equipped.
  • Node Attached and Communicate correctly: Airflow mode actuator is equipped, communication with airflow mode actuator is normal.
  • Node Attached but Not Communicate correctly: Airflow mode actuator is equipped, but communication with airflow mode actuator is not normal.
 -
MODE_PS_ACTAT_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
MTTR_TIMER hour If the ignition is switched OFF after a specified time has elapsed or the vehicle has been driven for a specified period of time or more while in the fail-safe mode, the ignition will remain switched off and the engine cannot be started. Displays the elapsed time since the engine could no longer be started. -
NOX1_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
NOX2_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
OHC_ROOMLAMP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Front map light is not equipped.
  • Node Attached and Communicate correctly: Front map light is equipped, communication with front map light is normal.
  • Node Attached but Not Communicate correctly: Front map light is equipped, but communication with front map light is not normal.
 -
OIL_LVL_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Engine oil level sensor is not equipped.
  • Node Attached and Communicate correctly: Engine oil level sensor is equipped, communication with engine oil level sensor is normal.
  • Node Attached but Not Communicate correctly: Engine oil level sensor is equipped, but communication with engine oil level sensor is not normal.
 -
OMC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Driver monitoring camera unit is not equipped.
  • Node Attached and Communicate correctly: Driver monitoring camera unit is equipped, communication with driver monitoring camera unit is normal.
  • Node Attached but Not Communicate correctly: Driver monitoring camera unit is equipped, but communication with driver monitoring camera unit is not normal.
 -
OMM_LGHT_OFF Off/On  
  • Off: Battery discharge suppression signal is not sent from body control module (BCM).
  • On: Battery discharge suppression signal is sent from body control module (BCM).
 -
ONE_TOUCH_TURN Off/On  
  • Off: Turn switch LH signal or the turn switch RH signal is not received.
  • On: Turn switch LH signal or the turn switch RH signal is received.
 -
OUTLET_L1_REQ  
NOTE:
  • Displays in the M-MDS but it does not operate.
OUTLET_R1_REQ  
NOTE:
  • Displays in the M-MDS but it does not operate.
PARK_RANGE_SW Off/On  
  • Off: NOT P position switch is off.
  • On: NOT P position switch is on.
 -
PCM_PT_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: PCM is not equipped.
  • Node Attached and Communicate correctly: PCM is equipped, communication via CAN BUS No. 2 with PCM is normal.
  • Node Attached but Not Communicate correctly: PCM is equipped, but communication via CAN BUS No. 2 with is not normal.
 -
PCM_VEH_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: PCM is not equipped.
  • Node Attached and Communicate correctly: PCM is equipped, communication via CAN BUS No. 1 with PCM is normal.
  • Node Attached but Not Communicate correctly: PCM is equipped, but communication via CAN BUS No. 1 with is not normal.
 -
PLG_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
PMS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Position memory control module is not equipped.
  • Node Attached and Communicate correctly: Position memory control module is equipped, communication with position memory control module is normal.
  • Node Attached but Not Communicate correctly: Position memory control module is equipped, but communication with position memory control module is not normal.
 -
PNC_ALRM_HZRD No Request/Request Control  
  • Off: Hazard warning light flashing request signal is not received.
  • On: Hazard warning light flashing request signal is received.
 -
PNC_ALRM_REQ*5 No Request/Request Control  
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
POWER_MODE OFF/ACC/ON/CRANK  
  • OFF: Body control module (BCM) controls ignition switch off (lock).
  • ACC: Body control module (BCM) controls ignition switch ACC.
  • ON: Body control module (BCM) controls ignition switch ON (engine off).
  • CRANK: Body control module (BCM) controls cranking at ignition switch ON.
 -
PSM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Parking assist unit (ultrasonic) is not equipped.
  • Node Attached and Communicate correctly: Parking assist unit (ultrasonic) is equipped, communication with parking assist unit (ultrasonic) is normal.
  • Node Attached but Not Communicate correctly: Parking assist unit (ultrasonic) is equipped, but communication with parking assist unit (ultrasonic) is not normal.
 -
PTC_HEAT_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
R_FOG_SW_IN  
NOTE:
  • Displays in the M-MDS but it does not operate.
R_FOG_SW_OUT  
NOTE:
  • Displays in the M-MDS but it does not operate.
R_MIX_ACTAT_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
R_TIMER_MODE Off/On  
  • OFF: Intermittent wiper operation of rear wiper is disabled.
  • ON: Intermittent wiper operation of rear wiper is enabled.
 -
R_VENT_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Rear vent actuator is not equipped.
  • Node Attached and Communicate correctly: Rear vent actuator is equipped, communication with rear vent actuator is normal.
  • Node Attached but Not Communicate correctly: Rear vent actuator is equipped, but communication with rear vent actuator is not normal.
 -
R_WASH_SW Off/On  
  • Off: Rear wiper and washer switch is not in rear washer position.
  • On: Rear wiper and washer switch is in rear washer position.
 -
R_WIP OFF/Rear Wiper Lo/Not defined/Wiper INT  
  • Off: Rear wiper and washer switch is in the OFF position.
  • Rear Wiper Lo: Rear wiper and washer switch is in the ON position.
  • Not defined: Rear wiper and washer switch position is not determined.
  • Wiper INT: Rear wiper and washer switch is in the INT position.
 -
R_WIP_CTRL Deactivate/Activate/Fail (Circuit Short to Ground)/Fail (Circuit Open)/Fail (Circuit Short to Battery) Rear wiper operation condition input signal from electrical supply unit (ESU)
  • Deactivate: Rear wiper is not operated.
  • Activate: Rear wiper is operated.
  • Fail (Circuit Short to Ground): Short to ground circuit malfunction is received from rear wiper.
  • Fail (Circuit Open): Open circuit malfunction is received from rear wiper.
  • Fail (Circuit Short to Battery): Short to battery circuit malfunction is received from rear wiper.
 -
R_WIP_POS Unknown/Parking_Position/Not_Parking_Position/AS_SW_Failure  
  • Unknown: Rear wiper position is not determined.
  • Parking_Position: Rear wiper in park position.
  • Not_Parking_Position: Rear wiper in position other than park.
  • AS_SW_Failure: Autostop switch has a malfunction.
 -
R_WIP_REQ OFF/Rear Wiper Low On/Stop  
  • Off: Body control module (BCM) does not operate rear wiper.
  • Rear Wiper Low On: Body control module (BCM) operates rear wiper.
  • Stop: Body control module (BCM) operates rear wiper to the park position.
 -
R_WIP_STALL_STAT OK/Stall  
  • OK: Rear wiper motor is normal.
  • Stall: Rear wiper motor is stalled.
 -
RCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: SAS control module is not equipped.
  • Node Attached and Communicate correctly: SAS control module is equipped, communication with SAS control module is normal.
  • Node Attached but Not Communicate correctly: SAS control module is equipped, but communication with SAS control module is not normal.
 -
REGEN_NETWORK  
NOTE:
  • Displays in the M-MDS but it does not operate.
RES Off/On  
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
RES_HZRD_ANS No Request/Request Control  
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
RF_TMTR FALSE/TRUE  
  • FALSE: Remote transmitter ID information is not programmed in LF control unit.
  • TRUE: Remote transmitter ID information is programmed in LF control unit.
 -
RLS_AMB_TEMP °C Displays rain sensor ambient temperature. -
RLS_AUTO_LGHT_REQ TNS Off/Head_Off/TNS On/Head Off/TNS On/Head On Illumination request by receiving TNS or headlight illumination request signal.
  • TNS Off/Head_Off: Body control module (BCM) does not operate the TNS (parking lights) and headlight on.
  • TNS On/Head Off: Body control module (BCM) operates the TNS (parking lights) on.
  • TNS On/Head On: Body control module (BCM) operates the TNS (parking lights) and headlight on.
 -
RLS_CTRL OFF/TNS Only ON/Low and TNS/Unknown Illumination request by receiving auto light signal, TNS or headlight illumination request signal.
  • OFF: Body control module (BCM) does not operate the TNS (parking lights) and headlight on.
  • TNS Only ON: Body control module (BCM) operates the TNS (parking lights) on.
  • Low and TNS: Body control module (BCM) operates the TNS (parking lights) and headlight on.
  • Unknown: TNS (parking lights) condition is not detected.
 -
RLS_FAIL Normal/Fault  
  • Normal: Error signals is not received from the auto light sensor.
  • Fault: Error signals is received from the auto light sensor.
 -
RLS_FAIL_STAT Faulty (Faulty)/Initialize/Not within specifications/Normal (sensing) Displays auto light sensor condition input signal -
RLS_FWD_LGHT_SEN OK/NG  
  • OK: Normal forward brightness can be detected.
  • NG: Normal forward brightness cannot be detected.
 -
RLS_I_ILLMI_MODE Unknown/Off (day_mode)/On (night_mode)  
  • Unknown: Panel light illumination request signal is not determined.
  • Off (day_mode): Panel light illumination request signal is not received.
  • On (night_mode): Panel light illumination request signal is received.
 -
RLS_LGHT_SEN_FAIL Normal/Fault  
  • Normal: Error signals is not received from the auto light sensor.
  • Fault: Error signals is received from the auto light sensor.
 -
RLS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not equipped.
  • Node Attached and Communicate correctly: Humidity sensor/solar radiation sensor/auto light sensor/rain sensor is equipped, communication with humidity sensor/solar radiation sensor/auto light sensor/rain sensor is normal.
  • Node Attached but Not Communicate correctly: Humidity sensor/solar radiation sensor/auto light sensor/rain sensor is equipped, but communication with humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not normal.
 -
RLS_RAIN_SEN_FAIL Off/On  
  • Off: Error signals is not received from the rain sensor.
  • On: Error signals is received from the rain sensor.
 -
RLS_RELAT_HMDTY % Displays relative humidity. -
RLS_STAT OFF/TNS On requested/TNS/Headlight On requested/TNS/Headlight On requested  
  • Off: TNS (parking lights) and headlight illumination request signal is not received.
  • TNS On requested: TNS (parking lights) illumination request signal is received.
  • TNS/Headlight On requested: TNS (parking lights) and headlight illumination request signal is received.
  • TNS/Headlight On requested: TNS (parking lights) and headlight illumination request signal is received.
 -
RLS_TEMP_SEN_FAIL Normal/Fault  
  • Normal: Error signals is not received from the temperature sensor (built into humidity sensor).
  • Fault: Error signals is received from the temperature sensor (built into humidity sensor).
 -
RLS_UP_LGHT_SEN OK/NG  
  • OK: Normal upward brightness can be detected.
  • NG: Normal upward brightness cannot be detected.
 -
RLS_VOLT_FAIL Normal/Fault  
  • Normal: Power supply voltage of humidity sensor/solar radiation sensor/auto light sensor/rain sensor is normal.
  • Fault: Power supply voltage of humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not normal.
 -
RLS_WINDOW_TEMP °C Displays windshield temperature. -
RLS_WIP_REQ Wiper OFF/Wiper Off_during Auto INT/Single Wipe/Speed Low/Speed High/Failure  
  • Wiper OFF: Wiper operation signal is not received from rain sensor.
  • Wiper Off_during Auto INT: Error signals is received from the rain sensor.
  • Single Wipe: Signal to operate wiper once is received from rain sensor.
  • Speed Low: Signal to operate wiper at low speed is received from rain sensor.
  • Speed High: Signal to operate wiper at high speed is received from rain sensor.
  • Failure: Communication with rain sensor is failed.
 -
RSRL_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Rear side radar sensor (LH) is not equipped.
  • Node Attached and Communicate correctly: Rear side radar sensor (LH) is equipped, communication with rear side radar sensor (LH) is normal.
  • Node Attached but Not Communicate correctly: Rear side radar sensor (LH) is equipped, but communication with rear side radar sensor (LH) is not normal.
 -
S_BELT_LED_OFF_C/R Off/On  
  • Off: Rear seat belt (center) warning light is not illuminated.
  • On: Rear seat belt (center) warning light is illuminated.
 -
S_BELT_LED_OFF_L/R Off/On  
  • Off: Rear seat belt (LH) warning light is not illuminated.
  • On: Rear seat belt (LH) warning light is illuminated.
 -
S_BELT_LED_OFF_R/R Off/On  
  • Off: Rear seat belt (RH) warning light is not illuminated.
  • On: Rear seat belt (RH) warning light is illuminated.
 -
S_BELT_LED_ON_C/R Off/On  
  • Off: Rear seat belt (center) warning light is not illuminated.
  • On: Rear seat belt (center) warning light is illuminated.
 -
S_BELT_LED_ON_L/R Off/On  
  • Off: Rear seat belt (LH) warning light is not illuminated.
  • On: Rear seat belt (LH) warning light is illuminated.
 -
S_BELT_LED_ON_R/R Off/On  
  • Off: Rear seat belt (RH) warning light is not illuminated.
  • On: Rear seat belt (RH) warning light is illuminated.
 -
S_BELT_LED_P Off/On  
  • Off: Passenger seat belt warning light is not illuminated.
  • On: Passenger seat belt warning light is illuminated.
 -
S_BELT_STAT Valid/Unknown  
  • Valid: All rear seat belt warning light signals are normal.
  • Unknown: There is a rear seat belt warning light signal error.
 -
S_BELT_STAT_C/3RD  
NOTE:
  • Displays in the M-MDS but it does not operate.
S_BELT_STAT_C/R Rear Center belt not used (Close)/Rear Center belt used (Open)  
  • Rear Center belt not used (Close): Rear center seat belt is not fastened.
  • Rear Center belt used (Open): Rear center seat belt is fastened.
 -
S_BELT_STAT_L/3RD  
NOTE:
  • Displays in the M-MDS but it does not operate.
S_BELT_STAT_L/R Rear Left belt not used (Close)/Rear Left belt used (Open)  
  • Rear Left belt not used (Close): Rear left seat belt is not fastened.
  • Rear Left belt used (Open): Rear left seat belt is fastened.
 -
S_BELT_STAT_R/3RD  
NOTE:
  • Displays in the M-MDS but it does not operate.
S_BELT_STAT_R/R Rear Right belt not used (Close)/Rear Right belt not used (Open)  
  • Rear Right belt not used (Close): Rear right seat belt is not fastened.
  • Rear Right belt used (Open): Rear right seat belt is fastened.
 -
S_BELT_WRNG_D driver belt not used/driver belt used/fault (hole IC switch)/reserve (mech switch)  
  • driver belt not used: Driver seat belt is not fastened.
  • driver belt used: Driver seat belt is fastened.
  • fault (hole IC switch)/reserve (mech switch): Driver seat belt has a malfunction.
 -
S_BELT_WRNG_P driver belt not used/driver belt used/fault (hole IC switch)/reserve (mech switch)
  • driver belt not used: Passenger seat belt is not fastened.
  • driver belt used: Passenger seat belt is fastened.
  • fault (hole IC switch)/reserve (mech switch): Passenger seat belt has a malfunction.
 -
SAS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Steering angle sensor is not equipped.
  • Node Attached and Communicate correctly: Steering angle sensor is equipped, communication with steering angle sensor is normal.
  • Node Attached but Not Communicate correctly: Steering angle sensor is equipped, but communication with steering angle sensor is not normal.
 -
SCR_HZRD_REQ  
NOTE:
  • Displays in the M-MDS but it does not operate.
SEAT_LETER_ILLMI Off/On  
  • Off: Passenger air bag deactivation (PAD) lettering illumination is not illuminated.
  • On: Passenger air bag deactivation (PAD) lettering illumination is illuminated.
 -
SEAT_OCS_C/R  
NOTE:
  • Displays in the M-MDS but it does not operate.
SEAT_OCS_L/R  
NOTE:
  • Displays in the M-MDS but it does not operate.
SEAT_OCS_R/R  
NOTE:
  • Displays in the M-MDS but it does not operate.
SEAT_OCS_STAT  
NOTE:
  • Displays in the M-MDS but it does not operate.
SHIFT between 2 positions/P/R/N/D/S (2)/L (1)  
  • between 2 positions: Selector lever is between two positions.
  • P: Selector lever is in P position.
  • R: Selector lever is in R position.
  • N: Selector lever is in N position.
  • D: Selector lever is in D position.
  • S (2): Selector lever is in D position 2nd gear.
  • L (1): Selector lever is in D position 1st gear.
 -
SLAM_LCK Off/On  
  • On: With all of the following conditions met, lock knob on door equipped with door lock-link switch is locked and all doors are closed.
    • Ignition is switched OFF
    • Any door is open
  • Off: Conditions other than above
 -
SPARE_KEY_STAT Off/On  
  • Off: There is no spare key.
  • On: There is spare key.
 -
SSB_1 Off/On  
  • Off: Push button start switch 1 is off.
  • On: Push button start switch 1 is on.
 -
SSB_2 Off/On  
  • Off: Push button start switch 2 is off.
  • On: Push button start switch 2 is on.
 -
SSB_AMBER_REQ Off/On  
  • Off: Push button start indicator light (amber) is turned off.
  • On: Push button start indicator light (amber) is illuminated.
 -
SSB_GREEN_REQ Off/On  
  • Off: Push button start indicator light (green) is turned off.
  • On: Push button start indicator light (green) is illuminated.
 -
SSB_ILLMI_REQ Off/On  
  • Off: START/STOP/ENGINE indicator light is turned off.
  • On: START/STOP/ENGINE indicator light is illuminated.
 -
SSU_RES_NUM 0/1/2/3  
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
SSU_RES_STAT Disable/Enable  
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
STR_ANG ° (deg) Displays steering angle signal (absolute angle)
  • Steering wheel in neutral position: Near 0 degrees
  • Steering wheel turned to left: Changes from 0 degrees to positive
  • Steering wheel turned to right: Changes from 0 degrees to negative
 -
STR_COLM_LCK_CTRL  
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_COLM_LCK_GND  
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_COLM_LCK_POWER  
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_COLM_LCK_STAT  
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_HEAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Heated steering wheel control unit is not equipped.
  • Node Attached and Communicate correctly: Heated steering wheel control unit is equipped, communication with heated steering wheel control unit is normal.
  • Node Attached but Not Communicate correctly: Heated steering wheel control unit is equipped, but communication with heated steering wheel control unit is not normal.
 -
SUPER_LCK_ALL Off/On  
  • Off: Double locking function (With double locking) is not operated.
  • On: Double locking function (With double locking) is operated.
 2J, 2L
T/LGT_LCK_SW Off/On  
  • Off: Lock request signal is not received.
  • On: Lock request signal is received.
 4I
T/LGT_SW Close/Open  
  • Close: Trunk (4SD)/liftgate is closed.
  • Open: Trunk (4SD)/liftgate (5HB) is open.
 2J, 2L
T/LGT_ULCK Off/On  
  • Off: Body control module (BCM) does not operate to unlock.
  • On: Body control module (BCM) operates to unlock.
 2J, 2L
TCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: TCM is not equipped.
  • Node Attached and Communicate correctly: TCM is equipped, communication with TCM is normal.
  • Node Attached but Not Communicate correctly: TCM is equipped, but communication with TCM is not normal.
 -
TCM_PT2_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: TCM is not equipped.
  • Node Attached and Communicate correctly: TCM is equipped, communication via CAN BUS No. 2 with TCM is normal.
  • Node Attached but Not Communicate correctly: TCM is equipped, but communication via CAN BUS No. 2 with TCM is not normal.
 -
TCU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Telematics communication unit is not equipped.
  • Node Attached and Communicate correctly: Telematics communication unit is equipped, communication with telematics communication unit is normal.
  • Node Attached but Not Communicate correctly: Telematics communication unit is equipped, but communication with telematics communication unit is not normal.
 -
TEMP_LH_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Driver-side air mix actuator is not equipped.
  • Node Attached and Communicate correctly: Driver-side air mix actuator is equipped, communication with driver-side air mix actuator is normal.
  • Node Attached but Not Communicate correctly: Driver-side air mix actuator is equipped, but communication with driver-side air mix actuator is not normal.
 -
TEMP_RH_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Passenger-side air mix actuator is not equipped.
  • Node Attached and Communicate correctly: Passenger-side air mix actuator is equipped, communication with passenger-side air mix actuator is normal.
  • Node Attached but Not Communicate correctly: Passenger-side air mix actuator is equipped, but communication with passenger-side air mix actuator is not normal.
 -
TGT_VERIFY Error/OK Displays immobilizer system condition. -
TIRE_PRES_L/F kPa Displays tire pressure (wheel unit (LF)) -
TIRE_PRES_L/R kPa Displays tire pressure (wheel unit (LR)) -
TIRE_PRES_R/F kPa Displays tire pressure (wheel unit (RF)) -
TIRE_PRES_R/R kPa Displays tire pressure (wheel unit (RR)) -
TIRE_TEMP_L/F °C, °F Displays tire temperature (wheel unit (LF)) -
TIRE_TEMP_L/R °C, °F Displays tire temperature (wheel unit (LR)) -
TIRE_TEMP_R/F °C, °F Displays tire temperature (wheel unit (RF)) -
TIRE_TEMP_R/R °C, °F Displays tire temperature (wheel unit (RR)) -
TMTR_NUM 0/1/2/3/4/5/6 Displays registration number of the remote transmitter -
TNS_REQ Off/On  
  • Off: Body control module (BCM) does not operate the TNS (parking lights) on.
  • On: Body control module (BCM) operates the TNS (parking lights) on.
 -
TNS_SW Off/On  
  • Off: Light switch TNS (parking lights) signal is not received.
  • On: Light switch TNS (parking lights) signal is received.
 -
TOPOLOGY_ID - Displays topological ID -
TOTAL_DIST km Displays total traveled distance -
TPMS_FAIL Default/Zero Learnt/One Learnt/Two Learnt/Three Learnt/ABS Error/Maximum speed exceeded/Location not determined/Locate data issue Displays reason why tire position recognition failed. -
TPMS_MODE_L/F Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (LF) mode -
TPMS_MODE_L/R Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (LR) mode -
TPMS_MODE_R/F Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (RF) mode -
TPMS_MODE_R/R Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (RR) mode -
TUNER_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Remote tuner (RT) is not equipped.
  • Node Attached and Communicate correctly: Remote tuner (RT) is equipped, communication with remote tuner (RT) is normal.
  • Node Attached but Not Communicate correctly: Remote tuner (RT) is equipped, but communication with remote tuner (RT) is not normal.
 -
TURN_L Off/On  
  • Off: Turn switch LH signal is not sent from body control module (BCM).
  • On: Turn switch LH signal is sent from body control module (BCM).
 -
TURN_L_INTERIOR Off/On  
  • Off: Turn signal (LH) or hazard warning indicator signal is not sent from body control module (BCM).
  • On: Turn signal (LH) or hazard warning indicator signal is sent from body control module (BCM).
 -
TURN_R Off/On  
  • Off: Turn switch RH signal is not sent from body control module (BCM).
  • On: Turn switch RH signal is sent from body control module (BCM).
 -
TURN_R_INTERIOR Off/On  
  • Off: Turn signal (RH) or hazard warning indicator signal is not sent from body control module (BCM).
  • On: Turn signal (RH) or hazard warning indicator signal is sent from body control module (BCM).
 -
TURN_SW Turn Off/Turn Right ON/Turn Left ON/Unknown  
  • Turn Off: Turn switch is in OFF position.
  • Turn Right ON: Turn switch is in RH position.
  • Turn Left ON: Turn switch is in LH position.
  • Unknown: Turn switch position is not determined.
 -
USBHUB_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Auxiliary jack/usb port/sd card slot hub is not equipped.
  • Node Attached and Communicate correctly: Auxiliary jack/usb port/sd card slot hub is equipped, communication with auxiliary jack/usb port/sd card slot hub is normal.
  • Node Attached but Not Communicate correctly: Auxiliary jack/usb port/sd card slot hub is equipped, but communication with auxiliary jack/usb port/sd card slot hub is not normal.
 -
VCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Vehicle control module (VCM) is not equipped.
  • Node Attached and Communicate correctly: Vehicle control module (VCM) is equipped, communication with vehicle control module (VCM) is normal.
  • Node Attached but Not Communicate correctly: Vehicle control module (VCM) is equipped, but communication with vehicle control module (VCM) is not normal.
 -
VDT_MODE  
NOTE:
  • Displays in the M-MDS but it does not operate.
VMC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: 360°view monitor control module/parking assist unit (optical) is not equipped.
  • Node Attached and Communicate correctly: 360°view monitor control module/parking assist unit (optical) is equipped, communication with 360°view monitor control module/parking assist unit (optical) is normal.
  • Node Attached but Not Communicate correctly: 360°view monitor control module/parking assist unit (optical) is equipped, but communication with 360°view monitor control module/parking assist unit (optical) is not normal.
 -
VPWR_ACC V Displays voltage at body control module (BCM) terminal 2AE (ACC power supply) 2AE
VPWR_CBCM V Displays power supply voltage of body control module (BCM) -
VPWR_ESCL V Displays voltage at body control module (BCM) terminal 4W (power supply) 4W
VPWR_IG V Displays voltage at body control module (BCM) terminal 2AF (ignition power supply) 2AF
VPWR_LIMP_HOME V Displays voltage at body control module (BCM) terminal 1B (power supply) 1B
VPWR_ROOM V Displays voltage at body control module (BCM) terminal 1D (power supply) 1D
WASH_MOTOR_STAT OFF/Washer_Motor_L/Washer_Motor_R  
  • Off: Windshield washer motor relay and rear washer motor relay are off.
  • Washer_Motor_L: Windshield washer motor relay is on.
  • Washer_Motor_R: Rear washer motor relay is on.
 -
WIP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/Node Attached but Not Communicate correctly  
  • Node is not attached on Vehicle: Windshield wiper motor is not equipped.
  • Node Attached and Communicate correctly: Windshield wiper motor is equipped, communication with windshield wiper motor is normal.
  • Node Attached but Not Communicate correctly: Windshield wiper motor is equipped, but communication with windshield wiper motor is not normal.
 -
scientia non olet · About LEMON Manuals