Using The M-MDS

NOTE:

PIDs for the following parts are not available on this model. Go to the appropriate part inspection service information.
- Intake CMP sensor and exhaust CMP sensor (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION (VIN M) .)
- Main relay (See RELAY INSPECTION .)

Connect the M-MDS to the DLC-2.
Switch the ignition ON.
Measure the PID value.
- If PID value is not within the specification, follow the instructions in Action column.

NOTE:

The PID/DATA MONITOR function monitors the calculated value of the input/output signals in the PCM. Therefore, an output device malfunction is not directly indicated as a malfunction of the monitored value for the output device. If a monitored value of an output device is out of specification, inspect the monitored value of the input device related to the output control.
The simulation items that are used in the ENGINE CONTROL SYSTEM OPERATION INSPECTION are as follows.
- ACCS, AIRSHUT_DSD, ARPMDES, EVAPCP, EVAPCV, FAN1, FAN2, FP, INJ_1, INJ_2, INJ_3, INJ_4, LAFS_CM, OIL_P_SOL, Test

-: Not applicable

Item (definition)

Unit/Condition

Value type

Condition/Specification (Reference)

AAT (Ambient air temperature)

°C, °F

Displays ambient air temperature

ABV_OIL_P ⁽³⁾

Displays in the M-MDS but it does not operate.

AC_PRES (Refrigerant pressure)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Displays refrigerant pressure

Input

Refrigerant pressure is 1.0 MPa {10 kgf/cm² , 145 psi}: Approx. 1.58 V
Refrigerant pressure is 1.1 MPa {11 kgf/cm² , 160 psi}: Approx. 1.75 V
Refrigerant pressure is 1.2 MPa {12 kgf/cm² , 174 psi}: Approx. 1.88 V

AC_REQ (A/C request signal)

Off/On

Input

A/C switch OFF: Off
A/C switch ON: On

ACCS (A/C relay)

Off/On

Input

A/C relay is OFF: Off
A/C relay is ON: On

AIRSHUT_ACT ⁽¹⁾ (Active air shutter position)

Calculation

Active air shutter position is 0°: 0%
Active air shutter position is 90°: 100%

AIRSHUT_CAL ⁽¹⁾ (Active air shutter position)

Not Done/Completed

Calculation

Displays active air shutter fully open/closed position learning status

AIRSHUT_DSD ⁽³⁾ (Active air shutter position)

Calculation

Displays target active air shutter angle (percent)

ALTF (Generator field coil control duty value)

Calculation

Ignition switched ON (engine off): 0%
Idle: Approx. 46%
Racing (Engine speed is 2, 000 rpm): Approx. 36%

ALTF_ACT (Actually measured value of field coil current signal input from generator)

Calculation

Displays actual generator field current control duty value

ALTT V ⁽³⁾ (Generator output voltage)

Input

Idle (no electrical loads): Approx. 14 V (This is an internal calculation value and differs from terminal voltage)

AMB_TEMP (Ambient air temperature)

°C, °F

Calculation

Displays ambient air temperature

APP (Accelerator pedal position)

Calculation

Accelerator pedal released: Approx. 0%
Accelerator pedal depressed: Approx. 100%

APP1 (APP sensor No. 1)

Calculation

Accelerator pedal released: Approx. 15%
Accelerator pedal depressed: Approx. 90.58%

Input

Accelerator pedal released: Approx. 0.75 V
Accelerator pedal depressed: Approx. 4.52 V

APP2 (APP sensor No. 2)

Calculation

Accelerator pedal released: Approx. 7.45%
Accelerator pedal depressed: Approx. 45.49%

Input

Accelerator pedal released: Approx. 0.38 V
Accelerator pedal depressed: Approx. 2.26 V

ARPMDES (Target engine speed)

RPM

Calculation

Displays target engine speed

AXIO_G_S ⁽³⁾ (Recommended gear supported)

Off/On

Calculation

Displays recommended gear supported

AXIO_TG_V ⁽³⁾ (Recommended transmission gear for current vehicle conditions)

Off/On

Calculation

Displays recommended transmission gear for current vehicle conditions

BARO (Barometric pressure)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Displays BARO

BATT_CUR ⁽³⁾ (Battery current)

Calculation

Displays battery charge/discharge current value

BATT_DAY ⁽³⁾ (Number of days elapsed since current sensor initialization)

Calculation

Displays vehicle battery days in service

BATT_RES ⁽³⁾ (Battery internal resistance (estimated))

Calculation

Displays battery inferred internal resistance

BATT_SOC ⁽³⁾ (Battery charge condition (estimated))

Calculation

Displays battery estimated state of charge

BATT_TEMP ⁽³⁾ (Battery temperature)

°C, °F

Calculation

Displays battery fluid temperature

BATT_V ⁽³⁾ (Battery voltage)

Calculation

Displays battery voltage

BBP ⁽³⁾ (Power brake unit vacuum sensor)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Displays power brake unit vacuum

Input

Power brake unit vacuum is 7.54 kPa {0.0769 kgf/cm² , 1.09 psi}: approx. 0.29 V
Power brake unit vacuum is 96.7 kPa {0.986 kgf/cm² , 14.0 psi}: approx. 3.81 V

BFP ⁽³⁾ (Brake fluid pressure)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Displays brake fluid pressure

BOO (Brake switch No. 1 signal)

High/Low

Calculation

Brake pedal released: Low
Brake pedal depressed: High

BPA (Brake switch No. 2 signal)

High/Low

Calculation

Brake pedal released: Low
Brake pedal depressed: High

BT_AH_ACCMLTD (Battery accumulated amp hour (Ah))

Calculation

Displays battery accumulated amp hour

CATT11_DSD (Estimated catalytic converter temperature)

°C, °F

Calculation

Displays estimated catalytic converter temperature

CHRGLP (Charging system warning light)

Off/On

Calculation

Charging system warning light not illuminated: Off
Charging system warning light illuminated: On

CL_NMHC_MN_CP ⁽³⁾ (Catalyst monitoring completed/NMHC catalyst monitoring completed)

YES/NO

Calculation

Displays the catalyst monitoring completed/NMHC catalyst monitoring completed

CLR_DIST (Distance after DTC cleared)

Calculation

Displays the mileage after DTC cleared

CLU_CUT_SW ⁽³⁾ (Starter interlock switch status)

Displays in the M-MDS but it does not operate.

CLU_SW ⁽³⁾ (CPP switch status)

Displays in the M-MDS but it does not operate.

CMP_MNT_ENA ⁽³⁾ (Comprehensive component monitoring enabled)

YES/NO

Calculation

Displays comprehensive component monitoring enabled

COMP3_MNT ⁽³⁾ (Comprehensive component monitoring completed)

YES/NO

Calculation

Displays comprehensive component monitoring completed

CP_IGN_SP ⁽³⁾ (Compression ignition monitoring supported)

YES/NO

Calculation

Displays compression ignition monitoring supported

CPP ⁽³⁾ (Clutch pedal position)

Displays in the M-MDS but it does not operate.

CPP/PNP ⁽³⁾ (Shift lever position)

Displays in the M-MDS but it does not operate.

CSTNO1_OIDTR ⁽³⁾

Displays in the M-MDS but it does not operate.

CSTNO2_OIDTR ⁽³⁾

Displays in the M-MDS but it does not operate.

CSTNO3_OIDTR ⁽³⁾

Displays in the M-MDS but it does not operate.

CSTNO4_OIDTR ⁽³⁾

Displays in the M-MDS but it does not operate.

CSTNO5_OIDTR ⁽³⁾

Displays in the M-MDS but it does not operate.

CTLY_NMHC_MN ⁽³⁾ (Catalyst monitoring/NMHC catalyst monitoring)

No/Yes

Calculation

Displays catalyst monitoring/NMHC catalyst monitoring

D_IEV_CST ⁽³⁾ (Deactivation/Intake valve and exhaust valve control status)

Off/On

Calculation

Displays deactivation/intake valve and exhaust valve control status

DAY_LTOIC ⁽³⁾

Displays in the M-MDS but it does not operate.

DIS_EMD (Total traveled distance after EVAP monitoring is completed)

km, ft, mi

Calculation

Displays total traveled distance after EVAP monitoring is completed

ECT (Engine coolant temperature)

°C, °F

Calculation

Displays ECT

Input

ECT is 20°C {68°F}: Approx. 3.10 V
ECT is 40°C {104°F}: Approx. 2.16 V
ECT is 60°C {140°F}: Approx. 1.40 V
ECT is 80°C {176°F}: Approx. 0.87 V
ECT is 100°C {212°F}: Approx. 0.54 V

ECT2_V (ECT sensor No. 2 voltage)

Input

ECT is 20°C {68°F}: Approx. 3.10 V
ECT is 40°C {104°F}: Approx. 2.16 V
ECT is 60°C {140°F}: Approx. 1.40 V
ECT is 80°C {176°F}: Approx. 0.87 V
ECT is 100°C {212°F}: Approx. 0.54 V

EFCV_AP_C ⁽³⁾ (Exhaust shutter valve position desired)

° (deg)

Calculation

Displays exhaust shutter valve position desired

EFCV_AP_M ⁽³⁾ (Exhaust shutter valve position actual)

° (deg)

Calculation

Displays exhaust shutter valve position actual

EG_RUN_TIME ⁽³⁾ (Elapsed time since the engine was started)

Second

Calculation

Displays the elapsed time since the engine was started.

EGR_VVT_MN_CP ⁽³⁾ (EGR and/or VVT system monitoring completed)

YES/NO

Calculation

Displays EGR and/or VVT system monitoring completed

EGR_VVT_MNT ⁽³⁾ (EGR and/or VVT system monitoring)

No/Yes

Calculation

Displays EGR and/or VVT system monitoring

EN_OENE_LT ⁽³⁾ (Engine output energy (Lifetime) (kWh))

Calculation

Displays engine output energy (Lifetime) (kWh)

EN_OENE_R ⁽³⁾ (Engine output energy (Recent) (kWh))

Calculation

Displays engine output energy (Recent) (kWh)

ENG_CL_V_POS (Coolant control valve opening angle)

° (deg)

Calculation

Displays target coolant control valve opening angle

ENG_CL_V_POS_R (Coolant control valve opening angle raw)

° (deg)

Input

Ignition switched ON (engine off): Approx. 114°

ENG_EXH_F_RATE ⁽³⁾ (Engine exhaust flow rate (kg/h))

Calculation

Displays engine exhaust flow rate

ENG_FEL_RATE ⁽³⁾ (Engine fuel rate)

g/Sec

Calculation

Displays engine fuel rate

ENG_EX_FLW ⁽³⁾ (Engine exhaust flow rate)

Calculation

Displays engine exhaust flow rate

ENG_FRCTN_PER (Engine friction percent torque)

Calculation

Displays engine friction percent torque

ENG_REF_TRQ ⁽³⁾ (Engine reference torque)

Calculation

Displays engine reference torque

EOL (Engine oil level)

mm, in

Calculation

Displays engine oil level

EOP (Engine oil pressure)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Switch ignition ON (engine off): 0-1 kPa {0.00-0.01 kgf/cm² , 0.0-0.1 psi}
Idle: Approx. 150 kPa {1.53 kgf/cm2, 21.8 psi}

EOT2 (Engine oil temperature from engine oil level sensor)

°C, °F

Calculation

Displays engine oil temperature

EQ_RAT11 (Equivalence ratio (lambda))

Calculation

Idle (after warm up): Approx. 1

EQ_RAT11_DSD (Desired equivalence ratio (lambda))

Calculation

Indicate target lambda (Excess air factor = supplied air amount/theoretical air/fuel ratio)

ETC_ACT (Electric throttle control actual)

° (deg)

Calculation

Ignition switched ON (engine off)

Accelerator pedal released: Approx. 12.89°
Accelerator pedal depressed: Approx.
03°

Idle (after warm up)

Accelerator pedal released: Approx. 3.87°

ETC_DSD (Electric throttle control desired)

Calculation

Displays target TP angle (percent)

° (deg)

Calculation

Displays target TP angle

EVAP_SYS_MN ⁽³⁾ (Evaporative system monitoring)

No/Yes

Calculation

Displays evaporative system monitoring

EVAP_SYS_MN_CP ⁽³⁾ (Evaporative system monitoring completed)

YES/NO

Calculation

Displays evaporative system monitoring completed

EVAPCP (Purge solenoid valve duty value)

Calculation

Idle (after warm up): 0% (Engine coolant temperature 59°C {140°F} or less)
Racing (Engine speed 2, 000 rpm): Approx. 4.7%
Racing (Engine speed 4, 000 rpm): Approx. 35.35%

EVAPCV (Evaporative emission canister vent valve)

Off/On

Calculation

Simulation item (EVAPCV) is ON: On

FAN_DUTY

Displays in the M-MDS but it does not operate.

FAN1 (Cooling fan relay No. 1)

Off/On

Calculation

Cooling fan relay No. 1 not operating: Off
Cooling fan relay No. 1 operating: On

FAN2 (Cooling fan relay No. 2)

Off/On

Calculation

Cooling fan relay No. 2 not operating: Off
Cooling fan relay No. 2 operating: On

FAN3

Displays in the M-MDS but it does not operate.

FCL (Check fuel cap warning light)

Off/On

Calculation

Check fuel cap warning light not illuminated: Off
Check fuel cap warning light illuminated: On

FEO_ICC_LT ⁽³⁾ (Fueled engine operation ignition cycle counter (Lifetime))

Calculation

Displays fueled engine operation ignition cycle counter (Lifetime)

FEO_ICC_R ⁽³⁾ (Fueled engine operation ignition cycle counter (Recent))

Calculation

Displays fueled engine operation ignition cycle counter (Recent)

FIA (Fuel injection amount)

Calculation

Displays fuel injection amount

FLI (Fuel level)

Calculation

Fuel gauge level F: Approx. 100%
Fuel gauge level E: Approx. 0%

FP (Fuel pump relay)

Off/On

Calculation

Ignition switched ON (engine off): Off
Cranking: On
Idle (after warm up): On

FP_DUTY (Fuel pump control module)

Calculation

Ignition switched ON (engine off): Approx. 56.72%
Cranking: Approx. 95%
Idle (after warm up): Approx. 56.72%

FRP (Fuel distributor pressure)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Displays fuel distributor pressure

FRP_A (Actual fuel distributor pressure)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Ignition switched ON (engine off): Approx. 3.36 MPa {34.3 kgf/cm² , 487 psi}
Idle (after warm up): Approx. 2.96-3.13 MPa {30.2-31.9 kgf/cm² , 430-453 psi}
Racing (engine speed is 2, 000 rpm): Approx. 3.3 MPa {34 kgf/cm² , 479 psi}
Racing (engine speed is 4, 000 rpm): Approx. 4.94 MPa {50.4 kgf/cm² , 716 psi}

FRP_A_CMD (Target fuel distributor pressure)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Ignition switched ON (engine off): Approx. 6 MPa {61 kgf/cm² , 870 psi}
Idle (after warm up): Approx. 3.1 MPa {32 kgf/cm² , 450 psi}
Racing (engine speed is 2, 000 rpm): Approx. 3.37 MPa {34.4 kgf/cm² , 489 psi}
Racing (engine speed is 4, 000 rpm): Approx. 4.97 MPa {50.7 kgf/cm² , 721 psi}

FRP_A_CMD_S (Presence/non-presence of target fuel distributor pressure)

No/Yes

Calculation

With fuel distributor: Yes
Without fuel distributor: No

FRP_A_S (Presence/non-presence of actual fuel distributor)

No/Yes

Calculation

With fuel distributor: Yes
Without fuel distributor: No

FRP_GAUGE ⁽³⁾

Displays in the M-MDS but it does not operate.

FRT_A (Fuel distributor temperature)

°C, °F

Calculation

Displays fuel distributor temperature

FT_A_S (Presence/non-presence of fuel distributor temperature)

No/Yes

Calculation

With fuel distributor: Yes
Without fuel distributor: No

FTP (Fuel tank pressure sensor)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Displays fuel tank pressure

Input

Fuel tank pressure is equal to barometric pressure: Approx. 2.5 V

FUEL_LO_P ⁽³⁾

Displays in the M-MDS but it does not operate.

FUEL_LO_T ⁽³⁾

Displays in the M-MDS but it does not operate.

FU_SYS_CP ⁽³⁾ (Fuel system monitoring completed)

YES/NO

Calculation

Displays fuel system monitoring completed

FU_SYS_ENA ⁽³⁾ (Fuel system monitoring enabled)

YES/NO

Calculation

Displays fuel system monitoring enabled

FUEL_P_DSD (Fuel pressure desired)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Displays target fuel pressure

FUEL_PRES (Fuel pressure sensor)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Displays fuel pressure

Input

Idle (ECT 80°C {176°F})

Fuel pressure is 10 MPa {102 kgf/cm² , 1450 psi}: Approx. 1.4 V

FUELPW (Fuel injector duration)

Sec

Calculation

Idle (after warm up): Approx. 1.26 ms
Racing (engine speed is 2, 000 rpm): Approx. 1.2 ms
Racing (engine speed is 4, 000 rpm): Approx. 1.1 ms

FUELSYS ⁽³⁾ (Fuel system status)

OL/CL/OL_Drive/OL_Fault/CL_Fault

Calculation

Idle (after warm up): OL or CL
Racing (engine speed is 2, 000 rpm): CL
Deceleration fuel cut (accelerator pedal released from engine speed of 4, 000 rpm or more): OL-Drive

FUELSYS_CL ⁽³⁾ (Feedback status of fuel injection control)

Yes/No

Calculation

Ignition switched ON (engine off): Yes
Idle: No
Racing (engine speed is 2, 000 rpm): No
Racing (engine speed is 4, 000 rpm): No

FUELSYS_CL_FAULT ⁽³⁾ (Feedback status of fuel injection control)

Yes/No

Calculation

Ignition switched ON (engine off): Yes
Idle: Yes
Racing (engine speed is 2, 000 rpm): Yes
Racing (engine speed is 4, 000 rpm): Yes

FUELSYS_OL ⁽³⁾ (Feedback status of fuel injection control)

Yes/No

Calculation

Ignition switched ON (engine off): Yes
Idle: Yes
Racing (engine speed is 2, 000 rpm): Yes
Racing (engine speed is 4, 000 rpm): Yes

FUELSYS_OL_DRIVE ⁽³⁾ (Feedback status of fuel injection control)

Yes/No

Calculation

Ignition switched ON (engine off): Yes
Idle: Yes
Racing (engine speed is 2, 000 rpm): Yes
Racing (engine speed is 4, 000 rpm): Yes

FUELSYS_OL_FAULT ⁽³⁾ (Feedback status of fuel injection control)

Yes/No

Calculation

Ignition switched ON (engine off): Yes
Idle: Yes
Racing (engine speed is 2, 000 rpm): Yes
Racing (engine speed is 4, 000 rpm): Yes

GEAR (Gear commanded)

Unknown/1st/2nd/3rd/4th/5th/6th/Not in P/Park/Neutral/Drive/Reverse

Calculation

Selector lever at P position: Park
Selector lever at R position: Reverse
Selector lever at N position: Neutral
Selector lever in 1GR at D position: 1st

GENVDSD ⁽³⁾ (Generator voltage desired)

Calculation

Displays generator voltage desired.

HTR11 (A/F sensor heater)

Off/On

Calculation

Ignition switched ON (engine off): Off
Idle (after warm up): On

Calculation

Ignition switched ON (engine off): 0%
Idle (after warm up): Approx. 43%

HTR12 (HO2S heater control)

Off/On

Calculation

Ignition switched ON (engine off): Off
Idle (after warm up): On

Calculation

Ignition switched ON (engine off): 0%
Idle (after warm up): Approx. 53%

IAT (Intake air temperature No. 1)

°C, °F

Calculation

Displays IAT (No. 1)

Input

IAT is 20°C {68°F}: Approx. 2.70 V
IAT is 40°C {104°F}: Approx. 1.80 V
IAT is 60°C {140°F}: Approx. 1.20 V

IAT2 (Intake air temperature No. 2)

°C, °F

Calculation

Displays IAT (No. 2)

Input

IAT2 is 20°C {68°F}: Approx. 3.57 V
IAT2 is 40°C {104°F}: Approx. 2.70 V
IAT2 is 60°C {140°F}: Approx. 1.87 V

IMRC ⁽³⁾

Displays in the M-MDS but it does not operate.

IMTV ⁽³⁾

Displays in the M-MDS but it does not operate.

IG_CNT_LT ⁽³⁾ (Ignition counter (Lifetime))

Calculation

Displays ignition counter (Lifetime)

IG_CNT_R ⁽³⁾ (Ignition counter (Recent))

Calculation

Displays ignition counter (Recent)

INGEAR (Gears are engaged)

Off/On

Calculation

Selector lever at P position or N position: Off
Except above: On

INJ ⁽³⁾ (Fuel injector control status while the engine is idling)

Calculation

Displays the fuel injector control status while the engine is idling.

INLET_PRES ⁽³⁾

Displays in the M-MDS but it does not operate.

INT_CO_TEMP ⁽³⁾

Displays in the M-MDS but it does not operate.

ISC_FBK ⁽³⁾ (ISC feedback value)

Calculation

Displays ISC feedback value

ISC_FBK_LRN ⁽³⁾ (Learning value for calculating ISC feedback amount)

Calculation

Displays learning value for calculating ISC feedback amount

I-Stop_OFF ⁽⁴⁾ (i-stop OFF mode)

Off/On

Calculation

i-stop OFF switch OFF: Off
i-stop OFF switch ON: On

I-Stop_TRD ⁽⁴⁾ (i-stop transmission D position selected status)

Off/On

Calculation

D position: On
Except above: Off

I-Stop_VSP ⁽⁴⁾ (i-stop vehicle speed history flag)

Off/On

Calculation

Vehicle speed in which engine stop condition is met via i-stop control is detected: On
Except above: Off

I-Stop_VST ⁽⁴⁾ (i-stop vehicle stop flag)

Off/On

Calculation

Vehicle stop predicted: On
Except above: Off

IVS (Idle flag)

Off Idle/Idle

Calculation

Other than idling: Off Idle
Idle: Idle

KNOCKR (Ignition timing correction for suppressing engine knock) ⁽²⁾

° (deg)

Calculation

Ignition switched ON (engine off): 0°
Idle (after warm up): 0°

LAFS_CM

Displays in the M-MDS but it does not operate.

LOAD (Engine load)

Calculation

Idle (after warm up): Approx. 16.07%
Racing (engine speed is 2, 000 rpm): Approx. 13.33%
Racing (engine speed is 4, 000 rpm): Approx. 15.29%

LONGFT1 (Long term fuel trim)

Calculation

Idle (after warm up): Approx. -3.9%
Racing (engine speed is 2, 000 rpm): Approx. -0.78%
Racing (engine speed is 4, 000 rpm): Approx. -0.78%

LONGFT12 (Long term fuel trim (HO2S))

Calculation

Idle (after warm up): Approx. 0%

LOW_OIL (Engine Oil Level Status)

Never Detected/Detected

Calculation

Ignition switched ON (engine off): Detected
Idle (after warm up): Never Detected

LRN_KCS (Knock control system learning value)

Calculation

Displays knock control system learning value

M_GEAR ⁽³⁾ (Manual Gear Position)

Displays in the M-MDS but it does not operate.

MAF (Mass airflow)

g/Sec

Calculation

Displays MAF

Input

Ignition switched ON (engine off) (MAF: 0.00 g/s {0 lb/min}): Approx. 1.69 V (ECT is 53°C {127°F})
Idle (after warm up) (MAF: 2.50 g/s {0.331 lb/min}): Approx. 1.89 V (ECT is 93°C {199°F})
Racing (engine speed is 2, 000 rpm) (MAF: 3.80 g/s {0.503 lb/min}): Approx. 2.02 V (ECT is 95°C {203°F})

MAP (Manifold absolute pressure)

KPa {MPA}, mBar {BAR}, psi, in H20

Calculation

Displays MAP

MAP_V (MAP sensor voltage)

Input

Ignition switched ON (engine off) (MAP:100 kPa {1.02 kgf/cm² , 14.5 psi}): Approx. 4.04 V
Idle (after warm up) (MAP: 35 kPa {0.36 kgf/cm² , 5.1 psi}): Approx. 1.40 V
Racing (engine speed is 2, 000 rpm) (MAP: 26 kPa {0.27 kgf/cm² , 3.8 psi}): Approx. 1.01 V

MF_CAT_2 (Number of misfires corresponding to possible catalytic converter damage (No. 2 cylinder))

Calculation

Displays number of misfires corresponding to possible catalytic converter damage (No. 2 cylinder)

MF_CAT_3 (Number of misfires corresponding to possible catalytic converter damage (No. 3 cylinder))

Calculation

Displays number of misfires corresponding to possible catalytic converter damage (No. 3 cylinder)

MF_CAT_4 (Number of misfires corresponding to possible catalytic converter damage (No. 4 cylinder))

Calculation

Displays number of misfires corresponding to possible catalytic converter damage (No. 4 cylinder)

MF_CAT_FCC (Number of misfire determinations (for catalytic converter))

Calculation

Displays number of misfire determinations (for catalytic converter)

MF_CAT_TTL (Number of misfires corresponding to possible catalytic converter damage (total))

Calculation

Displays number of misfires corresponding to possible catalytic converter damage (total)

MF_CAT1 (Number of misfires corresponding to possible catalytic converter damage (No. 1 cylinder))

Calculation

Displays number of misfires corresponding to possible catalytic converter damage (No. 1 cylinder)

MF_EMI_2 (Number of misfires possibly affecting emission (No. 2 cylinder))

Calculation

Displays number of misfires possibly affecting emission (No. 2 cylinder)

MF_EMI_3 (Number of misfires possibly affecting emission (No. 3 cylinder))

Calculation

Displays number of misfires possibly affecting emission (No. 3 cylinder)

MF_EMI_4 (Number of misfires possibly affecting emission (No. 4 cylinder))

Calculation

Displays number of misfires possibly affecting emission (No. 4 cylinder)

MF_EMI_FCC (Number of misfire determinations (for emission))

Calculation

Displays number of misfire determinations (for emission)

MF_EMI_TTL (Number of misfires possibly affecting emission (total))

Calculation

Displays number of misfires possibly affecting emission (total)

MF_EMI1 (Number of misfires possibly affecting emission (No. 1 cylinder))

Calculation

Displays number of misfires possibly affecting emission (No. 1 cylinder)

MIL (Check engine light)

Off/On

Calculation

Check engine light not illuminated: Off
Check engine light illuminated: On

MIL_DIS (Travelled distance since the check engine light illuminated)

km, ft, mi

Calculation

Displays travelled distance since the check engine light illuminated

MSF_CP ⁽³⁾ (Misfire monitoring completed)

YES/NO

Calculation

Displays misfire monitoring completed

MSF_ENA ⁽³⁾ (Misfire monitoring enabled)

YES/NO

Calculation

Displays misfire monitoring enabled

NEUTRAL_SW1 ⁽³⁾ (Neutral switch No. 1)

Displays in the M-MDS but it does not operate.

NEUTRAL_SW2 ⁽³⁾ (Neutral switch No. 2)

Displays in the M-MDS but it does not operate.

O2_SH_PM_F ⁽³⁾ (Oxygen sensor heater monitoring/PM filter monitoring)

No/Yes

Calculation

Displays oxygen sensor heater monitoring/PM filter monitoring

O2_SH_PM_F_CP ⁽³⁾ (Oxygen sensor heater monitoring completed/PM filter monitoring completed)

YES/NO

Calculation

Displays oxygen sensor heater monitoring completed/PM filter monitoring completed

O2_SM_EGSM ⁽³⁾ (Oxygen sensor monitoring/Exhaust gas sensor monitoring)

No/Yes

Calculation

Displays oxygen sensor monitoring/exhaust gas sensor monitoring

O2_SM_EGSM_CP ⁽³⁾ (Oxygen sensor monitoring completed/Exhaust gas sensor monitoring completed)

YES/NO

Calculation

Displays oxygen sensor monitoring completed/exhaust gas sensor monitoring completed

O2S11 (A/F sensor)

μA

Input

Idle (after warm up): Approx. -39 μA
Deceleration fuel cut (accelerator pedal released from engine speed of 4, 000 rpm or more): Approx. 3.84 mA

O2S12 (HO2S)

Input

Idle (after warm up): 0-1.0 V
Deceleration fuel cut (accelerator pedal released from engine speed of 4, 000 rpm or more): Approx. 0 V

ODO_LTOIC ⁽³⁾

Displays in the M-MDS but it does not operate.

OIL_P_DUTY ⁽³⁾ (Engine oil pressure control circuit duty cycle)

Output

Displays engine oil pressure control circuit duty cycle

OIL_P_SOL (Engine oil solenoid valve)

Off/On

Calculation

ECT above 98°C {208°F} or engine speed above 4, 000 rpm: Off
ECT below 98°C {208°F} and engine speed below 4, 000 rpm: On

OIL_PRES (Engine oil solenoid valve)

Calculation

Displays estimated engine oil pressure

OIL_TEMP (Estimated engine oil)

°C, °F

Calculation

Displays estimated engine oil temperature

Calculation

Displays estimated engine oil temperature voltage

OPSV_DD_R ⁽³⁾

Displays in the M-MDS but it does not operate.

OPSV_EDRS ⁽³⁾

Displays in the M-MDS but it does not operate.

OPSV_ODRR ⁽³⁾

Displays in the M-MDS but it does not operate.

PKTC_ENE_LT ⁽³⁾ (Positive kinetic energy (Lifetime) (km/hr2))

Calculation

Displays positive kinetic energy (Lifetime) (km/hr2)

PKTC_ENE_R ⁽³⁾ (Positive kinetic energy (Recent) (km/hr2))

Calculation

Displays positive kinetic energy (Recent) (km/hr2)

PN_SW (Parking/neutral)

Open/Closed

Calculation

Selector lever at P position or N position: Closed
Except above: Open

PRS_TRQ_ACT ⁽³⁾ (Actual engine-percent torque)

Calculation

Displays actual engine-percent torque

REV_SW ⁽³⁾ (Back-up light switch status)

Displays in the M-MDS but it does not operate.

RO2FT1 (HO2S fuel trim)

Calculation

Idle (after warm up): Approx. 1.5%
Deceleration fuel cut (accelerator pedal released from engine speed of 4, 000 rpm or more): Approx. 3.99%

RPM (Engine speed)

RPM

Calculation

Displays engine speed

SEGRP ⁽³⁾

Displays in the M-MDS but it does not operate.

SEGRP ⁽³⁾

DSD Displays in the M-MDS but it does not operate.

SHRTFT1 (Short term fuel trim)

Calculation

Idle (after warm up): Approx. 2.34%
Racing (engine speed is 2, 000 rpm): Approx. 3.9%
Racing (engine speed is 4, 000 rpm): Approx. 1.56%

SHRTFT12 (Short term fuel trim (HO2S))

Calculation

Idle (after warm up): Approx. 0%

SPARKADV (Ignition timing)

° (deg)

Calculation

Displays ignition timing

Test (Test mode)

Off/On

Calculation

Test mode OFF: Off
Test mode ON: On

TH_M (Thermostat monitor)

°C, °F

Calculation

Displays thermostat monitor engine coolant temperature

Calculation

Displays thermostat monitor heat radiation ratio

TH_M_MAX (Thermostat monitor)

°C, °F

Calculation

Displays thermostat monitor engine coolant temperature (max limit)

Calculation

Displays thermostat monitor heat radiation ratio (max limit)

TH_M_MIN (Thermostat monitor)

°C, °F

Calculation

Displays thermostat monitor engine coolant temperature (min limit)

Calculation

Displays thermostat monitor heat radiation ratio (min limit)

Time_D_LR (Lean to rich delayed time)

Sec

Calculation

Displays lean to rich delayed time

Time_D_RL (Rich to lean delayed time)

Sec

Calculation

Displays rich to lean delayed time

Time_SR_LR (Lean to rich slow response time)

Sec

Calculation

Displays lean to rich slow response time

Time_SR_RL (Rich to lean slow response time)

Sec

Calculation

Displays rich to lean slow response time

TIMES_OD_SC ⁽³⁾

Displays in the M-MDS but it does not operate.

TM_GERT ⁽³⁾ (Transmission actual gear ratio)

Calculation

Displays transmission actual gear ratio

TM_GERT_SP ⁽³⁾ (Transmission actual gear ratio supported)

No/Yes

Calculation

Displays transmission actual gear ratio supported

TM_GEST ⁽³⁾ (Transmission actual gear status)

Calculation

Displays transmission actual gear status

TM_GEST_SP ⁽³⁾ (Transmission actual gear status supported)

No/Yes

Calculation

Displays transmission actual gear status supported

TP_REL (Relative throttle position)

Calculation

Accelerator pedal released: Approx. 12%
Accelerator pedal depressed: Approx. 82%

TP_UP_DSD_P ⁽³⁾

Displays in the M-MDS but it does not operate.

TP_UP_TEMP ⁽³⁾

Displays in the M-MDS but it does not operate.

TP1 (TP sensor No. 1)

Input

Accelerator pedal released: Approx. 1.11 V
Accelerator pedal depressed: Approx. 4.59 V

Calculation

Accelerator pedal released: Approx. 22%
Accelerator pedal depressed: Approx. 92%

TP2 (TP sensor No. 2)

Input

Accelerator pedal released: Approx. 3.92 V
Accelerator pedal depressed: Approx. 0.41 V

Calculation

Accelerator pedal released: Approx. 22%
Accelerator pedal depressed: Approx. 92%

TPCT (TP sensor No. 1 voltage at CTP)

Input

Ignition switched ON (engine off): Approx. 0.5 V

TPCT2 (TP sensor No. 2 voltage at CTP)

Input

Ignition switched ON (engine off): Approx. 4.5 V

TT_CPS_AT_LT ⁽³⁾ (Total city propulsion system active time (Lifetime))

hh:mm:ss

Calculation

Displays total city propulsion system active time (Lifetime)

TT_CPS_AT_R ⁽³⁾ (Total city propulsion system active time (Recent))

hh:mm:ss

Calculation

Displays total city propulsion system active time (Recent)

TT_DTRV_LT ⁽³⁾ (Total distance traveled (Lifetime))

km, ft, mi

Calculation

Displays total distance traveled (Lifetime)

TT_DTRV_R ⁽³⁾ (Total distance traveled (Recent))

km, ft, mi

Calculation

Displays total distance traveled (Recent)

TT_ERT_LT ⁽³⁾ (Total engine run time (Lifetime))

hh:mm:ss

Calculation

Displays total engine run time (Lifetime)

TT_ERT_R ⁽³⁾ (Total engine run time (Recent))

hh:mm:ss

Calculation

Displays total engine run time (Recent)

TT_FCSM_LT ⁽³⁾ (Total fuel consumed (Lifetime))

Calculation

Displays total fuel consumed (Lifetime)

TT_FCSM_R ⁽³⁾ (Total fuel consumed (Recent))

Calculation

Displays total fuel consumed (Recent)

TT_IE_RT_LT ⁽³⁾ (Total idle engine run time (Lifetime))

hh:mm:ss

Calculation

Displays total idle engine run time (Lifetime)

TT_IE_RT_R ⁽³⁾ (Total idle engine run time (Recent))

hh:mm:ss

Calculation

Displays total idle engine run time (Recent)

TT_IPS_AT_LT ⁽³⁾ (Total idle propulsion system active time (Lifetime))

hh:mm:ss

Calculation

Displays total idle propulsion system active time (Lifetime)

TT_IPS_AT_R ⁽³⁾ (Total idle propulsion system active time (Recent))

hh:mm:ss

Calculation

Displays total idle propulsion system active time (Recent)

TT_PS_AT_LT ⁽³⁾ (Total propulsion system active time (Lifetime))

hh:mm:ss

Calculation

Displays total propulsion system active time (Lifetime)

TT_PS_AT_R ⁽³⁾ (Total propulsion system active time (Recent))

hh:mm:ss

Calculation

Displays total propulsion system active time (Recent)

VDD_FTM ⁽³⁾

Displays in the M-MDS but it does not operate.

VEH_FEL_RATE ⁽³⁾ (Vehicle fuel rate)

g/Sec

Calculation

Displays vehicle fuel rate

VEH_ODO ⁽³⁾ (Vehicle odometer)

km, ft, mi

Calculation

Displays vehicle odometer

VEV_OIL_P ⁽³⁾

Displays in the M-MDS but it does not operate.

VPWR (Battery positive voltage)

Input

Displays battery voltage

VSS (Vehicle speed)

KPH, MPH

Calculation

Displays vehicle speed

VT_Adv_CM

Displays in the M-MDS but it does not operate.

VT_CM

VT_EX_DES (Desired exhaust valve timing)

° (deg)

Calculation

Displays desired exhaust valve timing

VT_IN_ACT (Actual intake valve timing)

° (deg)

Calculation

Displays actual intake valve timing

VT_IN_DES (Desired intake valve timing)

° (deg)

Calculation

Displays desired intake valve timing

VT_EX_ACT (Actual exhaust valve timing)

° (deg)

Calculation

Displays actual exhaust valve timing

VT_EX_DUTY (OCV control)

Calculation

Idle (after warm up): Approx. 0%
Racing (engine speed is 2, 000 rpm): Approx. 40%

WGP ⁽³⁾

Displays in the M-MDS but it does not operate.

WGV ⁽³⁾

Displays in the M-MDS but it does not operate.

WGV_ACT ⁽³⁾

Displays in the M-MDS but it does not operate.

WGV_DSD ⁽³⁾

Displays in the M-MDS but it does not operate.

⁽¹⁾	With active air shutter

⁽²⁾	Performs retard correction (negative indication) according to the occurrence of engine knock, and it approaches approx. 0° by the advance correction due to engine knock suppression.

⁽³⁾	If equipped

⁽⁴⁾	With i-stop