Electronic Stability Program DTCS (Esp9LEI Module)
ELECTRONIC STABILITY PROGRAM DTCS (ESP9LEI MODULE)
| MB DTC | Description |
|---|---|
| C000000 | Control unit 'Electronic stability program' is defective. |
| C000100 | Control unit 'Electronic stability program' is defective. |
| C000200 | Control unit 'Electronic stability program' is defective. |
| C000400 | Control unit 'Electronic stability program' is defective. |
| C000500 | Control unit 'Electronic stability program' is defective. |
| C000600 | Control unit 'Electronic stability program' is defective. |
| C000700 | Control unit 'Electronic stability program' is defective. |
| C000800 | Control unit 'Electronic stability program' is defective. |
| C000900 | Control unit 'Electronic stability program' is defective. |
| C000A00 | Control unit 'Electronic stability program' is defective. |
| C000B00 | Control unit 'Electronic stability program' is defective. |
| C000C00 | Control unit 'Electronic stability program' is defective. |
| C000D00 | Control unit 'Electronic stability program' is defective. |
| C000E00 | Control unit 'Electronic stability program' is defective. |
| C000F00 | Control unit 'Electronic stability program' is defective. |
| C001000 | Control unit 'Electronic stability program' is defective. |
| C001100 | Control unit 'Electronic stability program' is defective. |
| C001200 | Control unit 'Electronic stability program' is defective. |
| C002400 | Control unit 'Electronic stability program' is defective. |
| C002B00 | Control unit 'Electronic stability program' is defective. |
| C002C00 | Control unit 'Electronic stability program' is defective. |
| C002D00 | Control unit 'Electronic stability program' is defective. |
| C002E00 | Control unit 'Electronic stability program' is defective. |
| C002F00 | Control unit 'Electronic stability program' is defective. |
| C003000 | Control unit 'Electronic stability program' is defective. |
| C003100 | Control unit 'Electronic stability program' is defective. |
| C003200 | Control unit 'Electronic stability program' is defective. |
| C003300 | Control unit 'Electronic stability program' is defective. |
| C003400 | Control unit 'Electronic stability program' is defective. |
| C003500 | Control unit 'Electronic stability program' is defective. |
| C003600 | Control unit 'Electronic stability program' is defective. |
| C003700 | Control unit 'Electronic stability program' is defective. |
| C003800 | Control unit 'Electronic stability program' is defective. |
| C003A00 | Control unit 'Electronic stability program' is defective. |
| C003B00 | Control unit 'Electronic stability program' is defective. |
| C003C00 | Control unit 'Electronic stability program' is defective. |
| C003D00 | Control unit 'Electronic stability program' is defective. |
| C003E00 | Control unit 'Electronic stability program' is defective. |
| C003F00 | Control unit 'Electronic stability program' is defective. |
| C004000 | Control unit 'Electronic stability program' is defective. |
| C004100 | Control unit 'Electronic stability program' is defective. |
| C004200 | Shutoff of component 'High pressure and return pump' due to overheating |
| C004300 | Control unit 'Electronic stability program' is defective. |
| C004400 | Control unit 'Electronic stability program' is defective. |
| C004500 | Control unit 'Electronic stability program' is defective. |
| C004600 | Control unit 'Electronic stability program' is defective. |
| C004800 | Control unit 'Electronic stability program' is defective. |
| C004900 | Control unit 'Electronic stability program' is defective. |
| C004A00 | Control unit 'Electronic stability program' is defective. |
| C004B00 | Control unit 'Electronic stability program' is defective. |
| C004C00 | The control unit does not contain any software. |
| C004D00 | Control unit 'Electronic stability program' is defective. |
| C004E00 | Software release of control unit 'Electronic stability program' - Only for the development department |
| C004F00 | Software release of control unit 'Electronic stability program' - Only for the development department |
| C007000 | Software release of control unit 'Electronic stability program' - Only for the development department |
| C007100 | Signal 'Brake pressure sensor' of component 'Brake light switch' is implausible. |
| C007300 | Signal 'Brake pressure sensor' of component 'Brake light switch' is implausible. |
| C007500 | Component 'Brake light switch' is mechanically defective or its electrical lines have a fault. |
| C007600 | The attachment and the installation position of the component 'Brake light switch' are not correct. Signal of component 'Brake light switch : PERMANENTLY ON' |
| C007700 | The attachment and the installation position of the component 'Brake light switch' are not correct. |
| C007800 | The power supply of component ""Brake light switch"" has undervoltage. |
| C008000 | Function 'Overheating protection' is deactivated in control unit 'Electronic stability program'. |
| C008100 | Monitoring of brake temperature |
| C00B000 | Implausible ESP® control. Vehicle Dynamic Control (VDC). A malfunction was detected in component 'Yaw rate sensor for lateral and longitudinal acceleration'. |
| C00B100 | The behavior of the ABS control is implausible. |
| C00B200 | Control unit 'Electronic stability program' is defective. |
| C00C000 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00C100 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00C200 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00C300 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00C400 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00C500 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00C600 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00C900 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00CA00 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00CB00 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00CC00 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C00CD00 | Signal 'Yaw rate sensor for lateral and longitudinal acceleration' is implausible. |
| C010600 | The voltage supply of the valves is faulty. |
| C011700 | The control unit software is faulty. |
| C011800 | Control unit 'Electronic stability program' is defective. |
| C011900 | Control unit 'Electronic stability program' is defective. |
| C011A00 | Control unit 'Electronic stability program' is defective. |
| C011B00 | Control unit 'Electronic stability program' is defective. |
| C011C00 | Control unit 'Electronic stability program' is defective. |
| C011D00 | Control unit 'Electronic stability program' is defective. |
| C013000 | The signal 'Brake pressure sensor of left front axle' is not available. |
| C013100 | The signal 'Brake pressure sensor of left front axle' is not available. |
| C013300 | The signal 'Brake pressure sensor of left front axle' is not available. |
| C014000 | The signal 'Brake pressure sensor of right front axle' is not available. |
| C014200 | The signal 'Brake pressure sensor of right front axle' is not available. |
| C014300 | The signal 'Brake pressure sensor of right front axle' is not available. |
| C015000 | The signal 'Brake pressure sensor of master brake cylinder' is not available. |
| C015100 | The signal 'Brake pressure sensor of master brake cylinder' is not available. |
| C015200 | The signal 'Brake pressure sensor of master brake cylinder' is not available. |
| C017000 | Component 'Reverse gear' switch' is mechanically defective or its electrical lines have a fault. CAN signal 'Reverse gear' is implausible. PERMANENTLY OFF |
| C017100 | Component 'Reverse gear' switch' is mechanically defective or its electrical lines have a fault. CAN signal 'Reverse gear' is implausible. PERMANENTLY ON |
| C018000 | One or more RPM sensors supply implausible values. |
| C018500 | The power supply to the RPM sensors has a short circuit to positive. |
| C019100 | Control unit 'Electronic stability program' is defective. |
| C019500 | Control unit 'Electronic stability program' is defective. |
| C019600 | Control unit 'Electronic stability program' is defective. |
| C019700 | Component 'High pressure and return pump' has detected an overvoltage. |
| C019800 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C019C00 | Control unit 'N30/4 (Electronic Stability Program (ESP) control unit)' is defective or the power supply is faulty. Circuit 30_M |
| C019D00 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C019E00 | Control unit 'Electronic stability program' is defective. |
| C019F00 | Control unit 'Electronic stability program' is defective. |
| C01A000 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01A100 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01A200 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01A300 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01A400 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01A500 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01A600 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01A700 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01A800 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01A900 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01AA00 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01AB00 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30M |
| C01C000 | The power supply for component 'Sensor 'Brake vacuum' is not OK. |
| C01C100 | The power supply for component 'Sensor 'Brake vacuum' is not OK. |
| C01C200 | The power supply for component 'Sensor 'Brake vacuum' is not OK. |
| C01C300 | Signal 'Sensor 'Brake vacuum' is implausible. |
| C01C400 | The vacuum system is not leaktight. Brake vacuum TOO LOW |
| C01C500 | The vacuum system is not leaktight. Brake vacuum TOO LOW |
| C01CA00 | CAN signal 'Mode 'Dynamic braking' from control unit 'Electric parking brake' is missing or implausible. |
| C01D000 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30VR |
| C01D100 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30VR |
| C01D200 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30VR |
| C01D300 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30VR |
| C01D400 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30VR |
| C01D600 | The power supply of control unit 'Electronic stability program' is not OK. Kl. 30VR |
| C01F000 | Control unit 'Electronic stability program' is defective. |
| C020000 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C020100 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C021000 | The attachment and the installation position of the component 'Brake light switch' are not correct. Signal of component 'Brake light switch : PERMANENTLY ON' |
| C022000 | The CAN lines have a short circuit to each other. The CAN lines have a short circuit. |
| C022400 | The CAN lines have a short circuit to each other. The CAN lines have a short circuit. |
| C024000 | Control unit 'Electronic stability program' is defective. |
| C024100 | Control unit 'Electronic stability program' is defective. |
| C024200 | Control unit 'Electronic stability program' is defective. |
| C024300 | Control unit 'Electronic stability program' is defective. |
| C024400 | Control unit 'Electronic stability program' is defective. |
| C024500 | Control unit 'Electronic stability program' is defective. |
| C024600 | Control unit 'Electronic stability program' is defective. |
| C025000 | Control unit 'Electronic stability program' is defective. |
| C025100 | Control unit 'Electronic stability program' is defective. |
| C025200 | Control unit 'Electronic stability program' is defective. |
| C025300 | Control unit 'Electronic stability program' is defective. |
| C025400 | Control unit 'Electronic stability program' is defective. |
| C025500 | Control unit 'Electronic stability program' is defective. |
| C025600 | Control unit 'Electronic stability program' is defective. |
| C026000 | Control unit 'Electronic stability program' is defective. |
| C026100 | Control unit 'Electronic stability program' is defective. |
| C026200 | Control unit 'Electronic stability program' is defective. |
| C026300 | Control unit 'Electronic stability program' is defective. |
| C026400 | Control unit 'Electronic stability program' is defective. |
| C026500 | Control unit 'Electronic stability program' is defective. |
| C026600 | Control unit 'Electronic stability program' is defective. |
| C027000 | Control unit 'Electronic stability program' is defective. |
| C027100 | Control unit 'Electronic stability program' is defective. |
| C027200 | Control unit 'Electronic stability program' is defective. |
| C027300 | Control unit 'Electronic stability program' is defective. |
| C027400 | Control unit 'Electronic stability program' is defective. |
| C027500 | Control unit 'Electronic stability program' is defective. |
| C027600 | Control unit 'Electronic stability program' is defective. |
| C028000 | Control unit 'Electronic stability program' is defective. |
| C028100 | Control unit 'Electronic stability program' is defective. |
| C028200 | Control unit 'Electronic stability program' is defective. |
| C028300 | Control unit 'Electronic stability program' is defective. |
| C028400 | Control unit 'Electronic stability program' is defective. |
| C028600 | Control unit 'Electronic stability program' is defective. |
| C028700 | Control unit 'Electronic stability program' is defective. |
| C028800 | Control unit 'Electronic stability program' is defective. |
| C028900 | Control unit 'Electronic stability program' is defective. |
| C029000 | Control unit 'Electronic stability program' is defective. |
| C029100 | Control unit 'Electronic stability program' is defective. |
| C029200 | Control unit 'Electronic stability program' is defective. |
| C029300 | Control unit 'Electronic stability program' is defective. |
| C029400 | Control unit 'Electronic stability program' is defective. |
| C029600 | Control unit 'Electronic stability program' is defective. |
| C029700 | Control unit 'Electronic stability program' is defective. |
| C029800 | Control unit 'Electronic stability program' is defective. |
| C02A000 | Control unit 'Electronic stability program' is defective. |
| C02A100 | Control unit 'Electronic stability program' is defective. |
| C02A200 | Control unit 'Electronic stability program' is defective. |
| C02A300 | Control unit 'Electronic stability program' is defective. |
| C02A400 | Control unit 'Electronic stability program' is defective. |
| C02A600 | Control unit 'Electronic stability program' is defective. |
| C02A700 | Control unit 'Electronic stability program' is defective. |
| C02A800 | Control unit 'Electronic stability program' is defective. |
| C02B000 | Control unit 'Electronic stability program' is defective. |
| C02B100 | Control unit 'Electronic stability program' is defective. |
| C02B200 | Control unit 'Electronic stability program' is defective. |
| C02B300 | Control unit 'Electronic stability program' is defective. |
| C02B400 | Control unit 'Electronic stability program' is defective. |
| C02B600 | Control unit 'Electronic stability program' is defective. |
| C02B700 | Control unit 'Electronic stability program' is defective. |
| C02B800 | Control unit 'Electronic stability program' is defective. |
| C02C000 | Control unit 'Electronic stability program' is defective. |
| C02C100 | Control unit 'Electronic stability program' is defective. |
| C02C200 | Overheating protection - Actuation of the ABS solenoid valves |
| C02C300 | Control unit 'Electronic stability program' is defective. |
| C02C500 | Control unit 'Electronic stability program' is defective. |
| C02C600 | Control unit 'Electronic stability program' is defective. |
| C02C700 | Control unit 'Electronic stability program' is defective. |
| C02C800 | Control unit 'Electronic stability program' is defective. |
| C02C900 | Control unit 'Electronic stability program' is defective. |
| C02CA00 | Control unit 'Electronic stability program' is defective. |
| C02CB00 | Control unit 'Electronic stability program' is defective. |
| C02CC00 | Control unit 'Electronic stability program' is defective. |
| C02CD00 | Control unit 'Electronic stability program' is defective. |
| C02CE00 | Control unit 'Electronic stability program' is defective. |
| C02CF00 | Control unit 'Electronic stability program' is defective. |
| C02D000 | Control unit 'Electronic stability program' is defective. |
| C02D100 | Control unit 'Electronic stability program' is defective. |
| C02D200 | Control unit 'Electronic stability program' is defective. |
| C02D300 | Control unit 'Electronic stability program' is defective. |
| C02D400 | Control unit 'Electronic stability program' is defective. |
| C02D500 | Control unit 'Electronic stability program' is defective. |
| C02D600 | Control unit 'Electronic stability program' is defective. |
| C02D700 | Control unit 'Electronic stability program' is defective. |
| C02E000 | Control unit 'Electronic stability program' is defective. |
| C02E100 | Control unit 'Electronic stability program' is defective. |
| C02E200 | Control unit 'Electronic stability program' is defective. |
| C02E300 | Control unit 'Electronic stability program' is defective. |
| C02E400 | Control unit 'Electronic stability program' is defective. |
| C02E500 | Control unit 'Electronic stability program' is defective. |
| C02E600 | Control unit 'Electronic stability program' is defective. |
| C02E700 | Control unit 'Electronic stability program' is defective. |
| C02F000 | Control unit 'Electronic stability program' is defective. |
| C02F100 | Control unit 'Electronic stability program' is defective. |
| C02F200 | Control unit 'Electronic stability program' is defective. |
| C02F300 | Control unit 'Electronic stability program' is defective. |
| C02F400 | Control unit 'Electronic stability program' is defective. |
| C02F500 | Control unit 'Electronic stability program' is defective. |
| C02F600 | Control unit 'Electronic stability program' is defective. |
| C02F700 | Control unit 'Electronic stability program' is defective. |
| C02F800 | Control unit 'Electronic stability program' is defective. |
| C030000 | Control unit 'Electronic stability program' is defective. |
| C030100 | Control unit 'Electronic stability program' is defective. |
| C030200 | Control unit 'Electronic stability program' is defective. |
| C030300 | Control unit 'Electronic stability program' is defective. |
| C030400 | Control unit 'Electronic stability program' is defective. |
| C030500 | Control unit 'Electronic stability program' is defective. |
| C030600 | Control unit 'Electronic stability program' is defective. |
| C030700 | Control unit 'Electronic stability program' is defective. |
| C030800 | Control unit 'Electronic stability program' is defective. |
| C031100 | Control unit 'Electronic stability program' is defective. |
| C031300 | Control unit 'Electronic stability program' is defective. |
| C031400 | One or more RPM sensors supply implausible values. Tires or rims are not approved. A multipole ring is dirty or damaged. A magnetic interference field was detected. Component 'RPM sensor' is mechanically defective or its electrical lines have a fault. The installed sensor model is incorrect. |
| C031500 | The power supply of component ""Speed sensors"" has undervoltage. |
| C032000 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032100 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032300 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032600 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032700 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032800 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032900 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032A00 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032B00 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032C00 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032D00 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C032E00 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C033000 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C033100 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C033200 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C033300 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C033400 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C034000 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C034100 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C034200 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C034300 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C034400 | The attachment and the installation position of the control unit 'Electronic stability program' are not correct. |
| C035000 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C035100 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C035200 | CAN signal 'Status 'Rotary tumblers of front doors Right' from control unit 'User interface CAN bus' is missing or implausible. |
| C035300 | CAN signal 'Status 'Rotary tumblers of front doors Left' from control unit 'User interface CAN bus' is missing or implausible. |
| C035400 | CAN signal 'Status of rotary tumbler 'Liftgate' from control unit 'User interface CAN bus' is missing or implausible. |
| C035600 | The signal 'Reverse gear' is missing or is implausible. |
| C036000 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C036100 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C037000 | CAN signal 'Transmission' from control unit 'Combustion engine' is missing or implausible. |
| C037100 | CAN signal 'Transmission' from control unit 'Combustion engine' is missing or implausible. |
| C037500 | CAN signal 'Torque loss (absolute value)' from control unit 'Combustion engine' is missing or implausible. |
| C038000 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C038100 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C038200 | CAN signal 'Torque' from control unit 'Combustion engine' is missing or implausible. |
| C038300 | CAN signal 'Torque request' from control unit 'Combustion engine' is missing or implausible. |
| C038400 | CAN signal 'Torque' from control unit 'Combustion engine' is missing or implausible. |
| C039000 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C039100 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C039200 | CAN signal 'Torque' from control unit 'Combustion engine' is missing or implausible. |
| C039300 | CAN signal 'Torque' from control unit 'Combustion engine' is missing or implausible. |
| C039400 | CAN signal 'Torque' from control unit 'Combustion engine' is missing or implausible. |
| C03A000 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C03A100 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C03A200 | CAN signal 'Engine speed' from control unit 'Combustion engine' is missing or implausible. |
| C03A300 | CAN signal 'Status of engine operation' from control unit 'Combustion engine' is missing or implausible. |
| C03A400 | CAN signal 'Position sensor 'Accelerator pedal' from control unit 'Combustion engine' is missing or implausible. |
| C03A500 | CAN signal 'Position sensor 'Accelerator pedal' from control unit 'Combustion engine' is missing or implausible. |
| C03A600 | CAN signal 'Position sensor 'Accelerator pedal' from control unit 'Combustion engine' is missing or implausible. |
| C03B000 | No CAN message from control module 'Electronic ignition lock' or message is faulty. |
| C03B100 | No CAN message from control module 'Electronic ignition lock' or message is faulty. |
| C03C000 | The CAN signal from the control unit 'Electric parking brake' is faulty. |
| C03C100 | The CAN signal from the control unit 'Electric parking brake' is faulty. |
| C03C200 | CAN signal 'Requested braking torque' from control unit 'Electric parking brake' is missing or implausible. |
| C03C300 | CAN signal 'Status of electric parking brake' from control unit 'Electric parking brake' is missing or implausible. |
| C03C400 | CAN signal 'Status of electric parking brake' from control unit 'Electric parking brake' is missing or implausible. |
| C03C500 | CAN signal 'Mode 'Dynamic braking' from control unit 'Electronic ignition lock' is missing or implausible. |
| C03D000 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C03D100 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C03E000 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C03E100 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C03E200 | CAN signal 'Mode 'Dynamometer' from control unit 'Instrument cluster' is missing or implausible. |
| C03E300 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C03F000 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C03F100 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C03F200 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C03F300 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C03F400 | CAN signal 'Request for function 'ESP®' from control unit 'User interface CAN bus' is missing or implausible. |
| C040000 | The CAN signal from the control unit 'Steering column module' is faulty. |
| C040100 | The CAN signal from the control unit 'Steering column module' is faulty. |
| C040200 | CAN signal 'Steering angle speed' from control unit 'Steering column module' is missing or implausible. |
| C040300 | The CAN signal from the control unit 'Steering column module' is faulty. |
| C041000 | At least one of the RPM sensors is delivering an incorrect rotation direction. The signal from component 'Speed sensors' is faulty. Wheel rotation direction. The installed sensor model is incorrect. |
| C042000 | The signal from component 'Speed sensors' is faulty. The RPM sensors on the front axle are swapped. Different wear on the tires |
| C043000 | The signal from component 'Speed sensors' is faulty. The RPM sensors on the rear axle are swapped. Different wear on the tires |
| C045200 | CAN signal 'Steering angle' from control unit 'Steering column module' is missing or implausible. Calibration of control unit 'Electrical power steering' |
| C045300 | CAN signal 'Steering angle' from control unit 'Steering column module' is missing or implausible. Calibration of control unit 'Electrical power steering' |
| C045400 | CAN signal 'Steering angle' from control unit 'Steering column module' is missing or implausible. Calibration of control unit 'Electrical power steering' |
| C045600 | CAN signal 'Steering angle' from control unit 'Steering column module' is missing or implausible. Calibration of control unit 'Electrical power steering' |
| C045700 | CAN signal 'Steering angle' from control unit 'Steering column module' is missing or implausible. Calibration of control unit 'Electrical power steering' |
| C045A00 | CAN signal 'Steering angle' from control unit 'Steering column module' is missing or implausible. Calibration of control unit 'Electrical power steering' |
| C045B00 | CAN signal 'Steering angle' from control unit 'Steering column module' is missing or implausible. Calibration of control unit 'Electrical power steering' |
| C046000 | The direction of rotation of component 'RPM sensor of left front axle' is implausible. Inversion of rotation direction. The installed sensor model is incorrect. |
| C047000 | The direction of rotation of component 'RPM sensor of right front axle' is implausible. Inversion of rotation direction. The installed sensor model is incorrect. |
| C048000 | The direction of rotation of component 'RPM sensor of left rear axle' is implausible. Inversion of rotation direction. The installed sensor model is incorrect. |
| C049000 | The direction of rotation of component 'RPM sensor of right rear axle' is implausible. Inversion of rotation direction. The installed sensor model is incorrect. |
| C04A000 | One of the electrical lines to component 'RPM sensor of left front axle' has a short circuit or open circuit. |
| C04A100 | The voltage supply of component 'RPM sensor of left front axle' has short circuit to ground. |
| C04A200 | The signal line of component 'RPM sensor of left front axle' has a short circuit to positive. |
| C04A300 | The signal line of component 'RPM sensor of left front axle' has an open circuit or short circuit to ground. The power supply of component 'RPM sensor of left front axle' has an open circuit. |
| C04A400 | The wiring harness to component 'RPM sensor of left front axle' is not OK. |
| C04A600 | An implausible wheel speed signal was received. Component 'RPM sensor of left front axle' is loose. The air gap between component 'RPM sensor of left front axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04A700 | Component 'RPM sensor of left front axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of left front axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04AA00 | RPM sensor of left front axle. The installed sensor model is incorrect. |
| C04AB00 | Tires or rims are not approved. A multipole ring is dirty or damaged. A magnetic interference field was detected. Component 'RPM sensor of left front axle' has a mechanical defect. The installed sensor model is incorrect. |
| C04AC00 | An implausible wheel speed signal was received. Component 'RPM sensor of left front axle' is loose. The air gap between component 'RPM sensor of left front axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04AD00 | Component 'RPM sensor of left front axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of left front axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04AE00 | An implausible wheel speed signal was received. Component 'RPM sensor of left front axle' is loose. The air gap between component 'RPM sensor of left front axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04AF00 | An implausible wheel speed signal was received. Component 'RPM sensor of left front axle' is loose. The air gap between component 'RPM sensor of left front axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04B000 | Component 'RPM sensor of left front axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of left front axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04B100 | Component 'RPM sensor of left front axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of left front axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04B400 | RPM sensor of left front axle. The installed sensor model is incorrect. |
| C04C000 | One of the electrical lines to component 'RPM sensor of right front axle' has a short circuit or open circuit. |
| C04C100 | The voltage supply of component 'RPM sensor of right front axle' has short circuit to ground. |
| C04C200 | The signal line of component 'RPM sensor of right front axle' has a short circuit to positive. |
| C04C300 | The signal line of component 'RPM sensor of right front axle' has an open circuit or short circuit to ground. The power supply of component 'RPM sensor of right front axle' has an open circuit. |
| C04C400 | The wiring harness to component 'RPM sensor of right front axle' is not OK. |
| C04C600 | An implausible wheel speed signal was received. Component 'RPM sensor of right front axle' is loose. The air gap between component 'RPM sensor of right front axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04C700 | Component 'RPM sensor of right front axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of right front axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04CA00 | RPM sensor of right front axle. The installed sensor model is incorrect. |
| C04CB00 | Tires or rims are not approved. A multipole ring is dirty or damaged. A magnetic interference field was detected. Component 'RPM sensor of right front axle' has a mechanical defect. The installed sensor model is incorrect. |
| C04CC00 | An implausible wheel speed signal was received. Component 'RPM sensor of right front axle' is loose. The air gap between component 'RPM sensor of right front axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04CD00 | Component 'RPM sensor of right front axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of right front axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04CE00 | An implausible wheel speed signal was received. Component 'RPM sensor of right front axle' is loose. The air gap between component 'RPM sensor of right front axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04CF00 | An implausible wheel speed signal was received. Component 'RPM sensor of right front axle' is loose. The air gap between component 'RPM sensor of right front axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04D000 | Component 'RPM sensor of right front axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of right front axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04D100 | Component 'RPM sensor of right front axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of right front axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04D400 | RPM sensor of right front axle. The installed sensor model is incorrect. |
| C04E000 | One of the electrical lines to component 'RPM sensor of left rear axle' has a short circuit or open circuit. |
| C04E100 | The voltage supply of component 'RPM sensor of left rear axle' has short circuit to ground. |
| C04E200 | The signal line of component 'RPM sensor of left rear axle' has a short circuit to positive. |
| C04E300 | The signal line of component 'RPM sensor of left rear axle' has an open circuit or short circuit to ground. The power supply of component 'RPM sensor of left rear axle' has an open circuit. |
| C04E400 | The wiring harness to component 'RPM sensor of left rear axle' is not OK. |
| C04E600 | An implausible wheel speed signal was received. Component 'RPM sensor of left rear axle' is loose. The air gap between component 'RPM sensor of left rear axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04E700 | Component 'RPM sensor of left rear axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of left rear axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04EA00 | RPM sensor of left rear axle. The installed sensor model is incorrect. |
| C04EB00 | Tires or rims are not approved. A multipole ring is dirty or damaged. A magnetic interference field was detected. Component 'RPM sensor of left rear axle' has a mechanical defect. The installed sensor model is incorrect. |
| C04EC00 | An implausible wheel speed signal was received. Component 'RPM sensor of left rear axle' is loose. The air gap between component 'RPM sensor of left rear axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04ED00 | Component 'RPM sensor of left rear axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of left rear axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04EE00 | An implausible wheel speed signal was received. Component 'RPM sensor of left rear axle' is loose. The air gap between component 'RPM sensor of left rear axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04EF00 | An implausible wheel speed signal was received. Component 'RPM sensor of left rear axle' is loose. The air gap between component 'RPM sensor of left rear axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C04F000 | Component 'RPM sensor of left rear axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of left rear axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04F100 | Component 'RPM sensor of left rear axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of left rear axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C04F400 | RPM sensor of left rear axle. The installed sensor model is incorrect. |
| C050000 | One of the electrical lines to component 'RPM sensor of right rear axle' has a short circuit or open circuit. |
| C050100 | The voltage supply of component 'RPM sensor of right rear axle' has short circuit to ground. |
| C050200 | The signal line of component 'RPM sensor of right rear axle' has a short circuit to positive. |
| C050300 | The signal line of component 'RPM sensor of right rear axle' has an open circuit or short circuit to ground. The power supply of component 'RPM sensor of right rear axle' has an open circuit. |
| C050400 | The wiring harness to component 'RPM sensor of right rear axle' is not OK. |
| C050600 | An implausible wheel speed signal was received. Component 'RPM sensor of right rear axle' is loose. The air gap between component 'RPM sensor of right rear axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C050700 | Component 'RPM sensor of right rear axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of right rear axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C050A00 | RPM sensor of right rear axle. The installed sensor model is incorrect. |
| C050B00 | Tires or rims are not approved. A multipole ring is dirty or damaged. A magnetic interference field was detected. Component 'RPM sensor of right rear axle' has a mechanical defect. The installed sensor model is incorrect. |
| C050C00 | An implausible wheel speed signal was received. Component 'RPM sensor of right rear axle' is loose. The air gap between component 'RPM sensor of right rear axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C050D00 | Component 'RPM sensor of right rear axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of right rear axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C050E00 | An implausible wheel speed signal was received. Component 'RPM sensor of right rear axle' is loose. The air gap between component 'RPM sensor of right rear axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C050F00 | Component 'RPM sensor of right rear axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of right rear axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C051000 | An implausible wheel speed signal was received. Component 'RPM sensor of right rear axle' is loose. The air gap between component 'RPM sensor of right rear axle' and the sensor rotor is too large. A magnetic interference field was detected. |
| C051100 | Component 'RPM sensor of right rear axle' is mechanically defective or its electrical lines have a fault. The air gap between component 'RPM sensor of right rear axle' and the sensor rotor is too large. The installed sensor model is incorrect. A magnetic interference field was detected. A multipole ring is dirty or damaged. |
| C051400 | RPM sensor of right rear axle. The installed sensor model is incorrect. |
| C054000 | No CAN message from control module 'Electronic ignition lock' or message is faulty. |
| C054100 | No CAN message from control module 'Electronic ignition lock' or message is faulty. |
| C054200 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C054300 | Control unit 'N30/4 (Electronic Stability Program (ESP) control unit)' is defective or the power supply is faulty. Circuit 30_M |
| C056000 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C056100 | The CAN signal from the control unit 'Combustion engine' is faulty. |
| C057000 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C057100 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C057200 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C057300 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C058000 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C058100 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C058200 | CAN signal 'Winter tire maximum speed' from control unit 'Instrument cluster' is missing or implausible. |
| C059000 | The CAN signal from the control unit 'Multifunction camera' is faulty. |
| C059100 | The CAN signal from the control unit 'Multifunction camera' is faulty. |
| C059200 | The CAN signal from the control unit 'Multifunction camera' is faulty. |
| C05A000 | The CAN signal from the control unit 'Multifunction camera' is faulty. |
| C05A100 | The CAN signal from the control unit 'Multifunction camera' is faulty. |
| C05B000 | The CAN signal from the control unit 'Multifunction camera' is faulty. |
| C05B100 | The CAN signal from the control unit 'Multifunction camera' is faulty. |
| C05C000 | The CAN signal from the control unit 'Supplemental restraint system' is faulty. |
| C05C100 | The CAN signal from the control unit 'Supplemental restraint system' is faulty. |
| C05C200 | CAN signal 'Status 'Belt buckle 'Driver' from control unit 'Supplemental restraint system' is missing or implausible. |
| C05D000 | The CAN signal from the control unit 'Radar sensor system' is faulty. |
| C05D100 | The CAN signal from the control unit 'Radar sensor system' is faulty. |
| C05D200 | The CAN signal from the control unit 'Radar sensor system' is faulty. |
| C05D300 | CAN signal 'Requested engine torque' from control unit 'Radar sensor system' is missing or implausible. |
| C05D400 | CAN signal 'Brake Assist System' is implausible. |
| C05D500 | CAN signal 'Requested reduction of engine torque' from control unit 'Radar sensor system' is missing or implausible. |
| C05D600 | CAN signal 'Requested reduction of engine torque' from control unit 'Radar sensor system' is missing or implausible. |
| C05D700 | CAN signal 'Requested braking torque' from control unit 'Radar sensor system' is missing or implausible. |
| C05E000 | CAN signal 'Requested gear' from control unit 'Radar sensor system' is missing or implausible. |
| C05E100 | CAN signal 'Requested gear' from control unit 'Radar sensor system' is missing or implausible. |
| C05F000 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C05F100 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C05F500 | CAN signal 'Signal acquisition and actuation module' from control unit 'Electronic ignition lock' is missing or implausible. |
| C05F600 | CAN signal 'Signal acquisition and actuation module' from control unit 'Electronic ignition lock' is missing or implausible. |
| C05F700 | CAN signal 'Status of engine hood - Signal acquisition and actuation module' from control unit 'User interface CAN bus' is missing or implausible. |
| C05F800 | CAN signal 'Status of engine hood - Signal acquisition and actuation module' from control unit 'User interface CAN bus' is missing or implausible. |
| C060000 | The CAN signal from the control unit 'Steering column module' is faulty. |
| C060100 | The CAN signal from the control unit 'Steering column module' is faulty. |
| C061000 | CAN signal 'Status 'Steering wheel angle' from control unit 'Steering column module' is missing or implausible. |
| C061100 | CAN signal 'Status 'Steering wheel angle' from control unit 'Steering column module' is missing or implausible. |
| C061200 | CAN signal 'Status 'Steering wheel angle' from control unit 'Steering column module' is missing or implausible. |
| C061300 | CAN signal 'Status 'Steering wheel angle' from control unit 'Steering column module' is missing or implausible. |
| C063000 | CAN signal 'Steering assistance system' from control unit 'Electrical power steering' is missing or implausible. |
| C063100 | CAN signal 'Steering assistance system' from control unit 'Electrical power steering' is missing or implausible. |
| C063200 | CAN signal 'Steering assistance system' from control unit 'Electrical power steering' is missing or implausible. |
| C063300 | CAN signal 'Steering assistance system' from control unit 'Electrical power steering' is missing or implausible. |
| C063500 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C063600 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C064000 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C064100 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C064200 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C065000 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C065100 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C065200 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C065300 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C065400 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C065500 | CAN signal 'Status of central locking' from control unit 'Electronic ignition lock' is missing or implausible. |
| C065600 | CAN signal 'Status of central locking' from control unit 'Electronic ignition lock' is missing or implausible. |
| C066000 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C066100 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C066200 | CAN signal 'Button 'ESP®' from control unit 'User interface CAN bus' is missing or implausible. |
| C066300 | CAN signal 'Accept phone call / Voice control system' from control unit 'User interface CAN bus' is missing or implausible. |
| C066400 | CAN signal 'Signal of switch 'Telematic system' from control unit 'User interface CAN bus' is missing or implausible. |
| C066500 | CAN signal 'Button 'Downhill speed regulation' ACTUATED' from control unit 'User interface CAN bus' is missing or implausible. |
| C066600 | Button ""Downhill Speed Regulation (DSR)' is jammed. |
| C067000 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C067100 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C067200 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C068000 | CAN signal 'Vehicle speed request - CRUISE CONTROL' from control unit 'Electronic ignition lock' is missing or implausible. |
| C068100 | CAN signal 'Vehicle speed request - CRUISE CONTROL' from control unit 'Electronic ignition lock' is missing or implausible. |
| C068200 | CAN signal 'Vehicle speed request - CRUISE CONTROL' from control unit 'User interface CAN bus' is missing or implausible. |
| C068300 | CAN signal 'Vehicle speed request - CRUISE CONTROL' from control unit 'User interface CAN bus' is missing or implausible. |
| C068400 | CAN signal 'Vehicle speed request - CRUISE CONTROL' from control unit 'User interface CAN bus' is missing or implausible. |
| C068500 | CAN signal 'Status 'Rotary tumblers for rear doors Left' from control unit 'User interface CAN bus' is missing or implausible. |
| C068600 | CAN signal 'Status 'Rotary tumblers for rear doors Right' from control unit 'User interface CAN bus' is missing or implausible. |
| C069000 | CAN signal 'Vehicle identification' from control unit 'User interface CAN bus' is missing or implausible. |
| C069100 | CAN signal 'Vehicle identification' from control unit 'User interface CAN bus' is missing or implausible. |
| C069200 | CAN signal 'Vehicle identification' from control unit 'User interface CAN bus' is missing or implausible. |
| C069300 | CAN signal 'Vehicle identification' from control unit 'User interface CAN bus' is missing or implausible. |
| C069400 | CAN signal 'Clutch pedal' from control unit 'Combustion engine' is missing or implausible. |
| C069500 | CAN signal 'Clutch pedal' from control unit 'Combustion engine' is missing or implausible. |
| C06A000 | CAN signal 'Status 'Transmission control' from control unit 'Combustion engine' is missing or implausible. |
| C06A100 | CAN signal 'Status 'Transmission control' from control unit 'Combustion engine' is missing or implausible. |
| C06A300 | CAN signal 'Status 'Transmission control' from control unit 'Combustion engine' is missing or implausible. |
| C06A700 | Control unit 'N30/4 (Electronic Stability Program (ESP) control unit)' is defective. |
| C06A800 | Control unit 'N30/4 (Electronic Stability Program (ESP) control unit)' is defective. |
| C06A900 | CAN signal 'Brake request' from control unit 'PARKTRONIC' is missing or implausible. |
| C06AA00 | CAN signal 'Brake request' from control unit 'PARKTRONIC' is missing or implausible. |
| C06AB00 | CAN signal 'Brake request' from control unit 'PARKTRONIC' is missing or implausible. |
| C06AC00 | CAN signal 'Brake request' from control unit 'PARKTRONIC' is missing or implausible. |
| C06AD00 | CAN signal 'Brake request' from control unit 'PARKTRONIC' is missing or implausible. |
| C06AE00 | CAN signal 'Brake request' from control unit 'PARKTRONIC' is missing or implausible. |
| C06AF00 | CAN signal 'Brake request' from control unit 'PARKTRONIC' is missing or implausible. |
| C06E000 | Control unit 'Electronic stability program' is not calibrated or incorrectly calibrated. |
| C06E200 | Control unit 'Electronic stability program' is not calibrated or incorrectly calibrated. |
| C06F000 | CAN signal 'Steering angle' from control unit 'Steering column module' is missing or implausible. |
| C06F100 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C06F200 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C06F300 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C073000 | SSC Standstill check : Function 'HOLD function' is not OK. |
| C073100 | SSC Standstill check : The CAN messages of the control unit 'Combustion engine' or 'N15/11 (Fully integrated transmission control (VGS) electric controller unit)' are implausible. |
| C073200 | SSC Standstill check : Control unit 'Fully integrated transmission control' |
| C073300 | SSC Standstill check : Component 'Buffer battery' is defective. |
| C073400 | SSC Standstill check : DTR / HOLD function - The maximum actuation duration has been exceeded. |
| C073500 | SSC Standstill check : Faulty variant coding |
| C073600 | SSC Standstill check : Coding 'SSC Standstill check' is not identical in control units 'Electronic stability program' and 'Instrument cluster'. Coding 'SSC Standstill check' is not identical in control units 'Electronic stability program' and 'Signal acquisition and actuation module'. |
| C073900 | SSC Standstill check : Faulty variant coding |
| C073A00 | SSC Standstill check : An implausible signal 'PARK POSITION' was received from control unit 'Electronic stability program'. Control unit 'Fully integrated transmission control' |
| C073B00 | SSC Standstill check : Faulty variant coding |
| C073C00 | SSC Standstill check : Function 'HOLD function' is not OK. |
| C074100 | The VIN stored in control unit 'Electronic stability program' is different from the VIN retrieved from the vehicle. |
| C074200 | The control unit 'Electronic stability program' is not receiving any signals from the CAN bus of the component 'Electronic ignition lock'. CAN signal 'VIN' |
| C074300 | Faulty variant coding |
| C074500 | Faulty variant coding Antilock brake system (ABS) / Brake pressure distribution (EBV/EBD) |
| C074600 | Faulty variant coding Antilock brake system (ABS) / Brake pressure distribution (EBV/EBD) |
| C074700 | Faulty variant coding |
| C074800 | Faulty variant coding |
| C074900 | Faulty variant coding |
| C074A00 | Faulty variant coding |
| C074C00 | Faulty variant coding |
| C074D00 | Faulty variant coding - The global variant coding could not be read out of the CAN bus. |
| C074E00 | Faulty variant coding - The global variant coding could not be read out of the CAN bus. |
| C074F00 | SCN coding of control unit 'Electronic ignition lock' was performed. A new software release for control unit 'Electronic stability program' has been installed. The run-on of control unit 'Electronic stability program' is not complete in the last ignition cycle. |
| C075000 | Faulty variant coding - The SCN coding of control unit 'Electronic stability program' is implausible compared to the SCN coding of control unit 'Electronic ignition lock'. Brake system |
| C075100 | Faulty variant coding - The SCN coding of control unit 'Electronic stability program' is implausible compared to the SCN coding of control unit 'Electronic ignition lock'. Brake system |
| C075200 | Faulty variant coding - The SCN coding of control unit 'Electronic stability program' is implausible compared to the SCN coding of control unit 'Electronic ignition lock'. Rail vehicle / HBC Braking power |
| C075300 | Faulty variant coding - The SCN coding of control unit 'Electronic stability program' is implausible compared to the SCN coding of control unit 'Electronic ignition lock'. Rail vehicle / HBC Braking power |
| C075400 | Faulty variant coding - The SCN coding of control unit 'Electronic stability program' is not correct. Function 'Rail vehicle' is not enabled in control unit 'Electronic stability program'. |
| C075500 | Brake pressure NOT REACHED |
| C075600 | Brake pressure NOT REACHED |
| C081000 | CAN signal 'Status 'Collision Mitigation System & Pre-Crash' from control unit 'Radar sensor system' is missing or implausible. |
| C081100 | CAN signal 'Status 'Collision Mitigation System & Pre-Crash' from control unit 'Radar sensor system' is missing or implausible. |
| C082000 | Door contact ""Driver door"" has a malfunction. |
| C084000 | CAN signal 'WAKE-UP Circuit 15' from control unit 'Electronic ignition lock' is missing or implausible. |
| C084100 | CAN signal 'WAKE-UP Circuit 15' from control unit 'Electronic ignition lock' is missing or implausible. |
| C090000 | Monitoring of brake load - The function 'Preventive maintenance' cannot be activated. |
| C090100 | Monitoring of brake load - Brake pad wear at left front axle - |
| C090200 | Monitoring of brake load - Brake pad wear at right front axle - |
| C090300 | Monitoring of brake load - Brake pad wear at left rear axle - |
| C090400 | Monitoring of brake load - Brake pad wear at right rear axle - |
| C090500 | Monitoring of brake load - Brake pad wear at left front axle - |
| C090600 | Monitoring of brake load - Brake pad wear at right front axle - |
| C090700 | Monitoring of brake load - Brake pad wear at left rear axle - |
| C090800 | Monitoring of brake load - Brake pad wear at right rear axle - |
| C090900 | Left front axle : Overheating of service brake |
| C090A00 | Right front axle : Overheating of service brake |
| C090B00 | Left rear axle : Overheating of service brake |
| C090C00 | Right rear axle : Overheating of service brake |
| C095000 | One or more RPM sensors supply implausible values. |
| C095100 | One or more RPM sensors supply implausible values. |
| C096000 | Control unit 'Electronic stability program' is defective. |
| C096100 | Control unit 'Electronic stability program' is defective. |
| C096200 | Control unit 'Electronic stability program' is defective. |
| C096300 | Control unit 'Electronic stability program' is defective. |
| C097000 | SSC Standstill check : No CAN message from control module 'Electric parking brake' or message is faulty. |
| C097100 | SSC Standstill check : No CAN message from control module 'Electric parking brake' or message is faulty. |
| C097200 | SSC Standstill check : Activation of function 'SSC Standstill check' was completed. |
| C097300 | SSC Standstill check : An implausible signal 'PARK POSITION' was received from control unit 'Electronic stability program'. Control unit 'Fully integrated transmission control' |
| C09A000 | Software access data : Limit value EXCEEDED. |
| C09A100 | Software access data : Limit value EXCEEDED. |
| C0A0100 | SSC Standstill check : Control unit 'Electronic stability program' has detected an undervoltage. The battery is heavily discharged. |
| C0C0000 | The CAN signal from the control unit 'Steering column module' is faulty. |
| C113000 | Component 'Power steering pump' |
| C113100 | Component 'Power steering pump' |
| C113200 | Component 'Power steering pump' or its power supply has an open circuit or short circuit. |
| C113300 | Component 'Power steering pump' |
| C113400 | The voltage supply of component 'Power steering pump' has short circuit to positive. |
| C113500 | Component 'Power steering pump' or its power supply has an open circuit or short circuit. |
| C113600 | Component 'Power steering pump' has detected an undervoltage. |
| C113800 | Component 'Power steering pump' or its power supply has an open circuit or short circuit. |
| C113B00 | Component 'Power steering pump' has detected an undervoltage. |
| C113C00 | Component 'Power steering pump' has detected an undervoltage. |
| C114000 | Faulty variant coding - Proportioning valve |
| C119000 | The power supply of circuit 30_ECU, 30VR has undervoltage. (Sensor 'Brake vacuum'). |
| C119300 | Component 'Vacuum pump' is not initialized. |
| C119400 | Invalid actuation of the component 'Vacuum pump' |
| C119500 | The power supply or the signal line of component 'Sensor 'Brake vacuum' is faulty. |
| C11D000 | The test prerequisites for the road test are not satisfied. Sensor 'Longitudinal acceleration' |
| C11D100 | The test prerequisites for the road test are not satisfied. Sensor 'Longitudinal acceleration' |
| C11D200 | The test prerequisites for the road test are not satisfied. Sensor 'Lateral acceleration' |
| C11D300 | The test prerequisites for the road test are not satisfied. Sensor 'Lateral acceleration' |
| C11D400 | The test prerequisites for the road test are not satisfied. Sensor 'Rotational speed' |
| C11D500 | The test prerequisites for the road test are not satisfied. Sensor 'Rotational speed' |
| C11D600 | The test prerequisites for the road test are not satisfied. Brake pressure |
| C11D700 | The test prerequisites for the road test are not satisfied. Steering angle sensor |
| C11D800 | The test prerequisites for the road test are not satisfied. Steering angle sensor |
| C11D900 | The test prerequisites for the road test are not satisfied. Steering angle sensor |
| C11DA00 | Road test - The RPM sensors on the front axle are swapped. |
| C11DB00 | Road test - The RPM sensors on the rear axle are swapped. |
| C11DC00 | The road test is active. |
| C11DD00 | Road test SUCCESSFULLY COMPLETED |
| C200000 | Implausible ESP® control DGR Signal 'Brake light switch' is implausible. |
| C200100 | Implausible ESP® control DGR CAN signal 'CRUISE CONTROL' is implausible. |
| C200200 | Implausible ESP® control DGR Internal fault |
| C200300 | The function of mode 'Diagnostic mode is active.' has been misused. |
| C201000 | Implausible ESP® control DGR The function 'Dynamometer' is permanently activated. |
| C206000 | Function 'Dynamometer' is active. |
| C206100 | All-wheel drive Dynamometer : The function of mode 'Dynamometer' has been misused. |
| C206200 | Front wheel drive or rear wheel drive Dynamometer : The function of mode 'Dynamometer' has been misused. The function of mode 'Towing mode' has been misused. |
| C206300 | Front wheel drive or rear wheel drive Dynamometer : The function of mode 'Dynamometer' has been misused. The function of mode 'Towing mode' has been misused. |
| C206500 | Faulty variant coding - The SCN coding of control unit 'Electronic stability program' is implausible compared to the SCN coding of control unit 'Control unit 'COLLISION PREVENTION ASSIST'. Requested braking torque - Mode 'Dynamic braking' |
| C2200FF | Control unit 'Electronic stability program' is defective. |
| C320100 | CAN signal 'Engine torque' from control unit 'Combustion engine' is missing or implausible. |
| C320900 | Function 'CRUISE CONTROL' was temporarily switched off. |
| C321200 | CAN signal 'Accelerator pedal' from control unit 'Combustion engine' is missing or implausible. |
| C322000 | CAN signal 'Transmission variant' from control unit 'Combustion engine' is missing or implausible. |
| C322100 | CAN signal 'Reverse gear' from control unit 'Electronic ignition lock' is missing or implausible. |
| C323500 | The CAN signal from the control unit 'Instrument cluster' is faulty. |
| C325000 | CAN signal 'Status 'Steering angle' from control unit 'Steering column module' is missing or implausible. |
| C325400 | CAN signal 'Cruise control lever' from control unit 'Steering column module' is missing or implausible. |
| C325600 | CAN signal 'Cruise control lever' from control unit 'Steering column module' is missing or implausible. |
| C326000 | Faulty variant coding SSC Standstill check. The SCN coding of control unit 'Electronic stability program' is implausible compared to the SCN coding of control unit 'Electronic ignition lock'. |
| C326100 | The signal of component 'Brake light switch' is outside the permissible range. Status of input signal 'Electric parking brake' FAULTY |
| C326300 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C327500 | The control unit software is faulty. |
| C328500 | The CAN signal from the control unit 'Electronic ignition lock' is faulty. |
| C328900 | No CAN message from control module 'User interface CAN bus' or message is faulty. |
| C328A00 | The CAN signal from the control unit 'Electric parking brake' is faulty. |
| C329500 | The control unit software is faulty. |
| C329600 | The control unit software is faulty. |
| C329700 | The control unit software is faulty. |
| C329800 | The control unit software is faulty. |
| C329900 | The control unit software is faulty. |
| C329B00 | The control unit software is faulty. |
| C333400 | The control unit software is faulty. |
| C334000 | The control unit software is faulty. |
| C334100 | The control unit software is faulty. |
| C334200 | The control unit software is faulty. |
| C334300 | The control unit software is faulty. |
| C334400 | The control unit software is faulty. |
| C334500 | The control unit software is faulty. |
| C334600 | The control unit software is faulty. |
| C334700 | The control unit software is faulty. |
| C334800 | The control unit software is faulty. |
| C334900 | The control unit software is faulty. |
| C334A00 | The control unit software is faulty. |
| C334B00 | The control unit software is faulty. |
| C334C00 | The control unit software is faulty. |
| C338500 | The control unit software is faulty. |
| C338600 | The control unit software is faulty. |
| C350000 | CAN signal 'Brake request' from control unit 'PARKTRONIC' is missing or implausible. |
| C360000 | Event TSM Trailer Sway Mitigation |
| C360100 | Event VDC Vehicle Dynamics Controller |
| C360200 | Event PRE-SAFE® control CVD Critical vehicle dynamics |
| C360300 | Event PRE-SAFE® control Radar sensor |
| C360500 | Event HBA Hydraulic Brake Assist |
| C360600 | Event ABS control |
| C360A00 | Event DWTB Dynamic wheel torque brake |
| C360B00 | Brake : Status of system monitoring NOT ACTIVATED |
| C365000 | Development data (Monitor 1) |
| C365100 | Development data (Monitor 2) |
| C365200 | Development data (Monitor 3) |
| C365300 | Development data (Monitor 4) |
| C365400 | Development data (Monitor 5) |
| C365500 | Development data (Monitor 6) |
| C365600 | Development data (Monitor 7) |
| P007334 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007340 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007341 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007342 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007343 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007344 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007345 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007346 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007347 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007348 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007349 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P00734A | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P00734C | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007385 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |
| P007386 | The control unit has a malfunction. LRR3 - Long-Range Radar. DISTRONIC. FAS - Driver assistance system |