84 11 610 Removing And Installing/Replacing Eject Box (Cordless Keypad Handset)

WARNING: This page is about a different car, the 2008 BMW Alpina and 2007 BMW Alpina. However, it is still accessible from the selected car via links, so may be relevant.

Special tools required:

00 9 322
00 9 341

Unlock and open storage tray (drawer).

CAUTION: To avoid scratches, cover decorative trims with a protective cover (1).

Detach storage tray (4) as follows from function carrier:

Release lock (3) by turning with a 1 mm feeler gauge (2).
Pull storage tray (4) towards rear out of function carrier and set down on protective cover (1).

Fig 1: Pulling Storage Tray And Lock
Courtesy of BMW OF NORTH AMERICA, INC.

Press button (1) and remove SIM card holder (2).

NOTE: Follow next work step for removal (risk of damage).
Special tools 00 9 322 and 00 9 341 required.

Lever cover (3) in direction of arrow out of storage tray (4).

CAUTION: Do not damage ribbon cable (5).

NOTE: (6) = Protective cover

Fig 2: Removing SIM Card Holder

Courtesy of BMW OF NORTH AMERICA, INC.

Removing:

If fitted, release catches (4) with special tool 00 9 322 .

Installation:

Following parts of cover (7) must not be damaged or missing:

Catches
Spring
Release button
Catches
Guides
Catches

Fig 3: Identifying Catches, Spring, Release Button And Guides
Courtesy of BMW OF NORTH AMERICA, INC.

CAUTION: Do not under any circumstances touch circuit board (2) with hands (risk of damage).

Using special tool 00 9 341, unlock insert (1) and pull out slightly in direction of arrow.

Fig 4: Identifying Special Tool (00 9 341)

Courtesy of BMW OF NORTH AMERICA, INC.

CAUTION: Do not under any circumstances touch circuit board (2) with hands (risk of damage).

Disconnect plug connection (1).

Remove insert (3).

Fig 5: Identifying Plug Connection

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Ribbon cable (1) must be laid in guide (3).

Stop (4) and damper (5) must not be damaged.

Fig 6: Identifying Ribbon Cable, Stop And Damper

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: A hand mirror (4) will be required for viewing.

Installation:

Springs (1) must be correctly connected in mountings (2).

Catch (3) must not be damaged.

Fig 7: Identifying Hand Mirror And Spring

Courtesy of BMW OF NORTH AMERICA, INC.

Special tools required:

00 9 322
00 9 341

Unlock and open storage tray (drawer).

CAUTION: To avoid scratches, cover decorative trims with a protective cover (1).

Detach storage tray (4) as follows from function carrier:

Release lock (3) by turning with a 1 mm feeler gauge (2).
Pull storage tray (4) towards rear out of function carrier and set down on protective cover (1).

Fig 1: Pulling Storage Tray And Lock
Courtesy of BMW OF NORTH AMERICA, INC.

Press button (1) and remove SIM card holder (2).

NOTE: Follow next work step for removal (risk of damage).
Special tools 00 9 322 and 00 9 341 required.

Lever cover (3) in direction of arrow out of storage tray (4).

CAUTION: Do not damage ribbon cable (5).

NOTE: (6) = Protective cover

Fig 2: Removing SIM Card Holder

Courtesy of BMW OF NORTH AMERICA, INC.

Removing:

If fitted, release catches (4) with special tool 00 9 322 .

Installation:

Following parts of cover (7) must not be damaged or missing:

Fig 3: Identifying Catches, Spring, Release Button And Guides

Courtesy of BMW OF NORTH AMERICA, INC.

CAUTION: Do not under any circumstances touch circuit board (2) with hands (risk of damage).

Using special tool 00 9 341, unlock insert (1) and pull out slightly in direction of arrow.

Fig 4: Identifying Special Tool (00 9 341)

Courtesy of BMW OF NORTH AMERICA, INC.

CAUTION: Do not under any circumstances touch circuit board (2) with hands (risk of damage).

Disconnect plug connection (1).

Remove insert (3).

Fig 5: Identifying Plug Connection

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Ribbon cable (1) must be laid in guide (3).

Stop (4) and damper (5) must not be damaged.

Fig 6: Identifying Ribbon Cable, Stop And Damper

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: A hand mirror (4) will be required for viewing.

Installation:

Springs (1) must be correctly connected in mountings (2).

Catch (3) must not be damaged.

Fig 7: Identifying Hand Mirror And Spring

Courtesy of BMW OF NORTH AMERICA, INC.