54 10... Repair instructions for bonded seals

• If seals reveal partly detached protective film on delivery, they must not be bonded.
• Store seals at 5 °C to 40 °C.
• If, during the handling, the protective film has come off before bonding, it can still be bonded.
• Bonding at room and object temperature 25° ±5° C. Temperatures between 40 and 50 °C significantly increase initial adhesion.
• Seals, which are subjected to temperatures above 80 °C after bonding, will be very difficult to remove.
• Maximum storage time for replacement: see identification of the expiry date on packaging

A partially released bonding (rubber part adhesive tape or adhesive tape paint) up to 120 mm may be finished. Continue with Point 2.1.

A partially released bonding (rubber part adhesive tape or adhesive tape paint) above 120 mm may not  be finished. Gasket must be replaced. Continue with Point 2.2.

• 2.1 Repair of partially released bonding (adhesive tape rubber part or adhesive tape paint: 
  • 2.1.1 Clean faulty areas 
    • Release adhesive area of paint side from recesses and degrease with CLEANING AGENT R2 . Stick to air drying time > of 1 minute. Never use paint thinner!
    • This will usually partially destroy intact edge adhesive areas.
    • When removing, it is important to wipe off the adhesive area of the adhesive tape with a lint-free disposable cloth. (e.g. Kimtex blue or equivalent)
    • Carefully wipe off the adhesive areas.
    NOTE: Use necessary cotton- or fluff-free paper towel once only.
    Do not touch the adhesive area after cleaning.
  • 2.1.2 Apply adhesive 
    • Apply PROFILE RUBBER ADHESIVE  evenly as a thin layer first on the gasket and then on the painted surface.
    • Stick to air drying time of 2 to 3 minutes.
    IMPORTANT: Avoid contact with skin!
    Do not apply adhesive to visible painted surfaces.
  • 2.1.3 Press in rubber seal 
    • Press down gasket using contact pressure (forced pressure not necessary) for > 1 minute.
    IMPORTANT: Load can be applied to the bonding only after a period of 2 minutes. This waiting time is absolutely essential.
• 2.2 Replacement: 
  • 2.2.1 Peeling off the faulty rubber seal 
    • Beginning at the stop, the gasket with the adhesive tape is slowly separated from the paint.

      The gasket is slowly pulled off from an angle of approx. 20° while applying even tensile stress.

      If the gasket is pulled off too quickly, the adhesive tape can tear off and remain on the painted surface.

      The adhesive tape remaining on the painted surface must be removed with high cleaning costs.

    NOTE: When the adhesive tape separates from the gasket, the adhesive tape remaining on the paint must be fully separated at one location by approx. 10 mm until it is easy to grip.
    Pull off the adhesive tape by pulling strongly at an angle of approx. 20°.
    When existing gaskets are being peeled off with a hot air blower: Do not damage paintwork.
  • 2.2.2 Clean bonding surface 
    • if required, remove adhesive remains with ERASER DISK , do not damage paint.
    • Before a new bond, degrease the entire adhesive area with CLEANING AGENT R2 . Stick to air drying time > of 1 minute.
    NOTE: Use necessary cotton- or fluff-free paper towel once only.
    Do not touch the adhesive area after cleaning.
  • 2.2.3 Pull off protective film of the bonding surface 
    • Pull off the protective film off of the new gasket by approx. 15 cm using the tab.
    IMPORTANT: Once the protective film has been removed, do not under any circumstances touch the exposed bonding surface.
  • 2.2.4 Apply rubber seal 
    • Press on the gasket by hand continuously while pulling off the liner slightly at the same time.
      NOTE: If positioned incorrectly, the gasket can still be pulled off, repositioned and pressed on again.
      Always ensure that you do not touch the bonding surface with your fingers or contaminate it in any way.
    • Compress the gasket the corners; never stretch it. (critical area)
  • 2.2.5 Establish sealing joint 
    • Where the beginning and end meet, a mark is created from pressing the loose end onto the beginning of the gasket.
    • Cut off the gasket vertically along the marked line (use sharp knife or special scissors) and press in place.
    • Visually check the pre-bonded gasket.
    NOTE: Small areas of gasket can remain stuck to adhesive tape of loose end.
  • 2.2.6 Press gasket 
    • Press gasket by hand or hand roller
    • Adhesive tape width up to 5 mm, contact pressure > 5 N/cm²
    • Adhesive tape width up to 10 mm, contact pressure > 10 N/cm²
    NOTE: Firm thumb pressure has approx. 35 N/cm²

• Check the bonded gaskets for correct positioning and perfect adhesion. The bonding can be checked by pressing back the sealing lip.
• The peel strength of the gasket must be greater than 10 N/cm² for about 15 min after bonding.