31 11 506 Lowering/raising front axle support (SWZ00-2040): Notes

WARNING: This page is about a different variant/trim than selected.

Special tools required:

00 2 030
00 2 040
31 4 051
31 4 090

WARNING: Danger of injury.
Failure to comply with the following instructions may result in the vehicle slipping off the lifting platform and critically injuring other persons.
When supporting components, make sure that:

the vehicle can no longer be raised or lowered
the vehicle does not lift off the locating plates on the vehicle hoist

IMPORTANT: Before lowering/removing front axle support:
Observe SAFETY INFORMATION for raising the vehicle
In order to avoid damage to vehicle hoist, perform weight compensation on vehicle.
Load spring strut domes with sand bags.

Necessary preliminary tasks:

Remove FRONT WHEELS .
If necessary, REMOVE UNDERBODY PROTECTION (diesel only ).
Remove complete exhaust system. See REMOVING COMPLETE EXHAUST SYSTEM (N16) or REMOVING COMPLETE EXHAUST SYSTEM (N14, N18) .
Remove LOWER BUMPER PANEL .
Partially remove FRONT LEFT AND RIGHT WHEEL ARCH COVERS .
If necessary, remove underbody panelling left and right. (R56, R58)
Only on left side at ride height sensor: Release PLUG CONNECTION AT SENSOR and move back cable.

IMPORTANT: If the steering shaft is separated from the steering box, this can result in damage to the steering column switch cluster when the steering wheel is turned.

Release screw (1).

Tightening torque 32 31 2AZ .

Detach lower section of steering shaft (2) from steering box and swing towards rear.

Installation note:

Fig 1: Detaching Lower Section Of Steering Shaft From Steering Box

Courtesy of BMW OF NORTH AMERICA, INC.

Clean thread to remove all remnants of screw locking adhesive.

Replace screw.

Disconnect plug connections (1) on steering box.

IMPORTANT: Make sure when lowering the front axle that the cable is not damaged.

Fig 2: Identifying Steering Box Plug Connections

Courtesy of BMW OF NORTH AMERICA, INC.

Disengage cable (1) of pulse sensor on left and right from holder on front axle support.

IMPORTANT: Make sure when lowering the front axle that the cable of the pulse sensor is not damaged.

Fig 3: Identifying Pulse Sensor Cable

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1) and remove anti-roll bar link (2).

Tightening torque 22 11 6AZ .

Installation note:

First mount front axle support on engine support and then tighten down screws (1).

Fig 4: Identifying Stabilizer Link And Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1) on bumper holder on left.

Tightening torque 51 11 4AZ .

Fig 5: Identifying Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1) on bumper holder on right.

Tightening torque 51 11 4AZ .

IMPORTANT: Make sure when lowering the front axle that the cable is not damaged.

Unclip cable tie (2).

Cut open cable strap (3).

Installation note:

Replace cable strap.

Fig 6: Identifying Cable Strap, Cable Tie, And Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Position special tool 00 2 040 with help of 2nd person on workshop jack 00 2 030 .

Insert special tools 31 4 051 and 31 4 090 into corresponding receptacles of special tool 00 2 040.

IMPORTANT: The journals of the special tool 31 4 090 must be completely inserted into the bore holes of the front axle support.

Align special tools 31 4 051 and 31 4 090 to front axle support.

Support front axle support by operating workshop jack 00 2 030 .

Fig 7: Inserting/Aligning Special Tools And Workshop Jack

Courtesy of BMW OF NORTH AMERICA, INC.

Unfasten screws (1) to (3).

Installation note:

Check threads for damage; if necessary, repair with HELICOIL THREAD INSERTS .

Make sure screws are installed in correct positions.

Screws (1) M12x85
Tightening torque 31 11 1AZ
Replace screws (2) M10x60.
Tightening torque 31 11 5AZ
Screws (3) M12x62
Tightening torque 31 11 2AZ

Fig 8: Identifying Screws
Courtesy of BMW OF NORTH AMERICA, INC.

Risk of damage.

When lowering the front axle support, it is absolutely essential to make sure that the control head (1) of the electric steering box (EPS) does not collide in area (2) with the bulkhead.

Collision with the bulkhead may result in damage to the electric steering box (EPS).

Fig 9: Identifying Control Head Of Electric Steering Gear (EPS)

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: When lowering and raising, make sure there is freedom of movement between front axle support, transmission and A/C lines.

Lower front axle support max. to dimension (A) = 120 mm.

Fig 10: Identifying Maximum Lowering Dimension Of Lower Front Axle Support

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Gasket (1) of electric steering box (EPS) must always be replaced.

Fig 11: Identifying Gasket Of Electric Steering Box (EPS)

Courtesy of BMW OF NORTH AMERICA, INC.