LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2002 >> Sentra SE-R, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 1694 (Transfer Case) >> TX15B >> Trouble Diagnosis >> Transfer Control Unit Input/Output Signal Reference Values >> Transfer Control Unit Inspection Table >> Specifications Between Transfer Control Unit Terminals
October 30: LEMON manuals on a temporary server, it is slow and having issues, download the manuals you need! Later in November we will switch back to the fast server.

Specifications Between Transfer Control Unit Terminals

WARNING: This page is about a different car, the 2006 Nissan Pathfinder. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Identifying Transfer Control Unit Connector Terminals Layout
G04174802Courtesy of NISSAN MOTOR CO., U.S.A.
NOTE: Data are reference value and are measured between each terminal and ground.
TRANSFER CONTROL UNIT TERMINALS VOLTAGE SPECIFICATION

Terminal Wire color Item Condition Data (Approx.)
1 L CAN-H - -
2 P CAN-L - -
3 SB K-LINE (CONSULT-II signal) - -
6 B Ground Always 0V
10 LG Actuator position switch 1
  • Vehicle stopped
  • Engine running
  • A/T selector lever "N" position
  • Brake pedal depressed
 4WD shift switch: 2WD and 4LO 0V
4WD shift switch: 4H Battery voltage
11 W Actuator position switch 2 4WD shift switch: 4LO 0V
4WD shift switch: 2WD and 4H Battery voltage
12 BR Actuator position switch 3 4WD shift switch: 2WD and 4H 0V
4WD shift switch: 4LO Battery voltage
13 L Actuator position switch 4 4WD shift switch: 4H and 4LO 0V
4WD shift switch: 2WD Battery voltage
14 G 4WD shift switch (2WD) Ignition switch: ON 4WD shift switch: 2WD Battery voltage
4WD shift switch: 4H and 4LO 0V
15 O 4WD shift switch (4H) 4WD shift switch: 4H Battery voltage
4WD shift switch: 2WD and 4LO 0V
16 W 4WD shift switch (4LO) 4WD shift switch: 4LO Battery voltage
4WD shift switch: 2WD and 4H 0V
17 O Wait detection switch
  • Vehicle stopped
  • Engine running
  • A/T selector lever "N" position
  • Brake pedal depressed
 4WD shift switch: 4H and 4LO 0V
4WD shift switch: 2WD Battery voltage
18 B Ground Always 0V
19 R Power supply (Memory back-up) Ignition switch: ON Battery voltage
Ignition switch: OFF Battery voltage
23 R ATP switch
  • Vehicle stopped
  • Engine running
  • A/T selector lever "N"
  • Brake pedal depressed
 4WD shift switch : 4H to 4LO or 4LO to 4H (While actuator motor is operating.) 0V
Except the above Battery voltage
24 Y 4LO switch
  • Vehicle stopped
  • Engine running
  • A/T selector lever "N" position
  • Brake pedal depressed
 4WD shift switch: 4LO 0V
Except the above Battery voltage
25 W/G Ignition switch monitor Ignition switch: ON Battery voltage
Ignition switch: OFF 0V
27 L Actuator motor power supply Ignition switch: ON Battery voltage
Ignition switch: OFF (5 seconds after ingnition switch is turned OFF) 0V
28 SB Actuator motor (+)
  • Vehicle stopped
  • Engine running
  • A/T selector lever "N" position
  • Brake pedal depressed
 When 4WD shift switch is operated (while actuator motor is operating) Battery voltage -> 0V
31 G Actuator motor (-) When 4WD shift switch is not operated 0V
Always 0V
32 B Ground Always 0V
35 V 4WD shift indicator lamp (Rear indicator) Engine running Rear indicator of 4WD shift indicator lamp : ON 0V
Rear indicator of 4WD shift indicator lamp : OFF Battery voltage
36 BR 4WD shift indicator lamp (Front and center indicator) Front and center indicator of 4WD shift indicator lamp: ON 0V
Front and center indicator of 4WD shift indicator lamp: OFF Battery voltage
37 O 4LO indicator lamp 4LO indicator lamp: ON 0V
4LO indicator lamp: OFF Battery voltage
38 GR 4WD warning lamp 4WD warning lamp: ON 0V
4WD warning lamp: OFF Battery voltage
39 LG ATP warning lamp
  • Vehicle stopped
  • Engine running
  • A/T selector lever "P" position
  • Brake pedal depressed
 4WD shift switch: 4H to 4LO or 4LO to 4H (While actuator motor is operating.) Battery voltage
Except the above 0V
40 V Transfer shut off relay Ignition switch: ON 0V
Ignition switch: OFF (5 seconds after ingnition switch is turned OFF) Battery voltage
42 LG Transfer shift high relay
  • Vehicle stopped
  • Engine running
  • A/T selector lever "N" position
  • Brake pedal depressed
 4WD shift switch: 2WD to 4H or 4H to 4LO or 2WD to 4LO 0V
Except the above Battery voltage
44 Y Power supply Ignition switch: ON Battery voltage
Ignition switch: OFF (5 seconds after ingnition switch is turned OFF) 0V
45 GR Power supply Ignition switch: ON Battery voltage
Ignition switch: OFF (5 seconds after ingnition switch is turned OFF) 0V
47 O Transfer shift high relay monitor
  • Vehicle stopped
  • Engine running
  • A/T selector lever "N" position
  • Brake pedal depressed
 4WD shift switch: 2WD to 4H or 4H to 4LO or 2WD to 4LO (while actuator motor is operating) Battery voltage -> 0V
Except the above 0V
48 R Transfer shift low relay monitor 4WD shift switch: 4LO to 4H or 4H to 2WD or 4LO to 2WD (while actuator motor is operating) Battery voltage -> 0V
Except the above 0V
50 Y Transfer shift low relay 4WD shift switch: 4LO to 4H or 4H to 2WD or 4LO to 2WD 0V
Except the above Battery voltage
CAUTION: When using a circuit tester to measure voltage for inspection, be sure not to extend forcibly any connector terminals.
scientia non olet · About LEMON Manuals