LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Pontiac >> 2001 >> Aztek Base, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1469 (Theft Deterrent System) >> Diagnostic Information and Procedures >> DTC B2958: Security System Sensor Data Circuit High >> Test Description
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test Description

WARNING: This page is about a different car, the 2003 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 3:  Tests for proper operation of the circuit in the high voltage range.
  2. 4:  Tests for proper operation of the circuit in the low voltage range.
  3. 5:  Tests for high resistance or an open in the 12V reference circuit.
  4. 7:  Tests for a short to voltage, a high resistance, or an open in the signal circuit.
  5. 8:  Tests for high resistance or an open in the ground circuit.
DTC B2958

Step Action Value(s) Yes No
Schematic Reference: Theft Deterrent System Schematics 
Connector End Reference: Theft Deterrent System Connector End Views 
1 Did you perform the Vehicle Theft Deterrent (VTD) Diagnostic System Check? - Go to Step 2  Go to Diagnostic System Check - Theft Deterrent 
2
  1. Install a scan tool.
  2. Momentarily rotate the ignition switch to CRANK, do not start the vehicle.
  3. Release the ignition switch to ON.
  4. With a scan tool, observe the Passlock™ Data Voltage in the Body Control Module Security Data list.
Does the scan tool indicate that the Passlock Data Voltage is within the specified range?		 0.4-4.9 V Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the Passlock™ sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool observe the Passlock™ Data Voltage in the Body Control Module Security Data list.
Does the scan tool indicate that the Passlock™ Data Voltage is greater than the specified value?		 4.9 V Go to Step 4  Go to Step 9 
4 
  1. Turn OFF the ignition.
  2. Connect a 3 amp fused jumper wire between the signal circuit of the Passlock™ sensor and the ground circuit of the Passlock™ sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool observe the Passlock™ Data Voltage in the Body Control Module Security Data list.
Does the scan tool indicate that the Passlock™ Data Voltage is less than the specified value?		 0.4 V Go to Step 5  Go to Step 7 
5 
  1. Disconnect the fused jumper wire.
  2. Measure the voltage between the 12V reference circuit of the Passlock™ sensor and the ground circuit of the Passlock™ sensor.
Does the voltage measure less than the specified value?		 12.0 V Go to Step 6  Go to Step 11 
6 Test the 12V reference circuit of the Passlock™ sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 14  Go to Step 9 
7  Test the signal circuit of the Passlock™ sensor for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 14  Go to Step 8 
8  Test the ground circuit of the Passlock™ sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 14  Go to Step 9 
9 Inspect for poor connections at the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 14  Go to Step 10 
10
IMPORTANT: When replacing the BCM, refer to Body Control Module (BCM) Programming/RPO Configuration in Body Control System.
Replace the body control module. Refer to Body Control Module Replacement in Body Control System.Did you complete the replacement?		 - Go to Step 14  -
11 Inspect for poor connections at the Passlock™ sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 14  Go to Step 12 
12 Replace the Passlock™ sensor in the electronic column lock module assembly. Refer to Ignition Lock Cylinder Replacement in Steering Wheel and Column.
Did you complete the replacement?		 - Go to Step 13  -
13 Perform the Programming Theft Deterrent System Components  procedure.
Is the repair complete?		 - Go to Step 14  -
14
  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition.
  3. Momentarily rotate the ignition switch to CRANK. Do not start the vehicle.
  4. Release the ignition switch to ON.
  5. Select the body control module display DTCs function on the scan tool.
Does the DTC reset?		 - Go to Step 3  Go to Step 15 
15 Attempt to start the vehicle.
Does the engine start and run?		 - System OK Go to Step 3 
scientia non olet · About LEMON Manuals