Specifications Index
GTO SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | NA | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LR, RF, LF | ||
| Disc Brakes | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Drum Brakes | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | NA | ||
| Belt Routing | See figure under DRIVE BELT REPLACEMENT - ACCESSORY or DRIVE BELT REPLACEMENT - AIR CONDITIONING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM DESCRIPTION AND OPERATION | ||
| Radiator Cap Pressure | Radiator cap pressure is stamped on cap. | ||
| Thermostat R & I | THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure Minimum - Hot |
6 psig (41 kPa) at 1,000 RPM 18 psig (124 kPa) at 2,000 RPM 24 psig (165 kPa) at 4,000 RPM |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| First Pass | 15 Ft. Lbs. (20 N.m) | ||
| Second Pass | 37 Ft. Lbs. (50 N.m) | ||
| Final Pass | 74 Ft. Lbs. (100 N.m) | ||
| Fuel System | |||
| Pressure Specification | 55-62 psi (385-425 kPa) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Fuel filter assembly is contained within modular fuel pump and sender assembly reservoir and forms containment housing for fuel pump. | ||
| Fuel Filter R & I | FUEL FILTER REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 188-312 Ohms | ||
| Ignition Wires (Routing) | Spark plugs wires route directly down from coil to spark plug | ||
| Spark Plug | |||
| Type | GM P/N 12571164 or AC 41-985 | ||
| Gap | 0.040 In. (1.02 mm) | ||
| Torque | 11 Ft. Lbs. (15 N.m) | ||
| Starting | |||
| Starter | STARTER MOTOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | |||
| First Pass | 50 Ft. Lbs. (70 N.m) | ||
| Second Pass | 100 Ft. Lbs. (140 N.m) | ||