Specifications Index
EQUINOX & TORRENT SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 151 lb ft (205 N.m) | ||
| Rear | 81 lb ft (110 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR-LF-LR-RF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | DISC BRAKE COMPONENT SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS |
||
| Drum Brakes | DRUM BRAKE COMPONENT SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS |
||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine belts are not adjustable | ||
| Belt Routing | See illustration under DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on cap | ||
| Thermostat R & I | |||
| 3.4L | THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | |||
| 3.4L | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 3.4L | |||
| Compression | No cylinder reading should be less than 689 kPa (100 psi). The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST |
||
| Oil Pressure | Oil Pressure - @ 1850 RPM 30-35 psi (207-241 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | 52 lb ft (71 N.m) | ||
| Fuel System | |||
| Pressure Specification | 50-60 psi (384-425 kPa) | ||
| Fuel Pressure Test Procedure | See Fuel Pressure Gage Installation and Removal and FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | The fuel filter (1) is located in the primary fuel tank module | ||
| Fuel Filter R & I | FUEL LEVEL SENSOR REPLACEMENT - PRIMARY | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 3.4L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 1,225 ohms per ft (4,018 ohms per meter) | ||
| Ignition Wires (Routing) | |||
| 3.4L | See illustrations under SPARK PLUG WIRE REPLACEMENT | ||
| Spark Plug | |||
| 3.4L (Type NA) | |||
| Gap | 0.60 in (1.52 mm) | ||
| Torque | 11 lb ft (15 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 92 lb ft (125 N.m) | ||