Specifications Index
EQUINOX & TORRENT SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 151 ft. lbs. (205 N.m) | ||
| Rear | 151 ft. lbs. (205 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR-LF-LR-RF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine drive belts are not adjustable | ||
| Drive Belt Routing | 3.4L - See illustrations under DRIVE BELT REPLACEMENT 3.6L - See illustrations under DRIVE BELT REPLACEMENT |
||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 3.4L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LNJ) | ||
| 3.6L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LY7) | ||
| Water Pump R & I | |||
| 3.4L | WATER PUMP REPLACEMENT (RPO LNJ) | ||
| 3.6L | WATER PUMP REPLACEMENT (RPO LY7) | ||
| Engine Mechanical | |||
| 3.4L | |||
| Compression | No cylinder reading should be less than 100 psi (689 kPa). The lowest reading should not be less than 70 percent of the highest reading. ENGINE COMPRESSION TEST |
||
| Oil Pressure | Oil Pressure - @ 1850 RPM 30-35 psi (207-241 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.6L | |||
| Compression | No cylinder reading should be less than 140 psi (965 kPa). The lowest reading should not be less than 70 percent of the highest reading. ENGINE COMPRESSION TEST |
||
| Oil pressure | Oil Pressure - Minimum @ Idle 10 psi (69 kPa) Oil Pressure - Minimum @ 2,000 RPM 20 psi (138 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| 3.4L | 52 ft. lbs. (71 N.m) | ||
| 3.6L | |||
| First Pass | 22 ft. lbs. (30 N.m) | ||
| Final Pass | + an additional 45 degrees | ||
| Fuel System | |||
| Pressure Specification | 3.4L - 56-62 psi (384-425 kPa) 3.6L - 55-60 psi (380-410 kPa) |
||
| Fuel Pressure Test Procedure | 3.4L - See FUEL PRESSURE GAGE INSTALLATION AND REMOVAL
and FUEL SYSTEM DIAGNOSIS 3.6L - See FUEL PRESSURE GAGE INSTALLATION AND REMOVAL and FUEL SYSTEM DIAGNOSIS |
||
| Fuel Filter Location | 3.4L - The fuel filter (1) is located in the primary fuel tank module 3.6L - The fuel filter (1) is located in the primary fuel tank module |
||
| Fuel Filter R & I | 3.4L - See PRIMARY FUEL TANK MODULE REPLACEMENT 3.6L - See PRIMARY FUEL TANK MODULE REPLACEMENT |
||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 3.4L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.6L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 3.4L - 1,225 Ohms per ft (4,018 Ohms per meter) 3.6L - Coil On Plug |
||
| Ignition Wires (Routing) | |||
| 3.4L | See illustrations under SPARK PLUG WIRE REPLACEMENT | ||
| 3.6L | Coil On Plug | ||
| Spark Plug | |||
| 3.4L (Type NA) | |||
| Gap | .060 in. (1.52 mm) | ||
| Torque | 11 ft. lbs. (15 N.m) | ||
| 3.6L (Type AC 41-990) | |||
| Gap | 0.044 in (1.10 mm) | ||
| Torque | 15 ft. lbs. (20 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 ft. lbs. (140 N.m) | ||