Remote Control Door Lock Receiver Scan Tool Information
WARNING: This page is about a different car, the 2010 Chevrolet Malibu. However, it is still accessible from the selected car via links, so may be relevant.
Remote Control Door Lock Receiver Scan Tool Data Parameters
| Parameter | System State | Expected Value | Description |
|---|---|---|---|
| Operating Conditions: Ignition ON | |||
| Battery Voltage Signal | - | Varies | This displays volts. This is the current battery voltage signal. |
| Ext. LF Door Handle Switch | - | Inactive | The scan tool displays Active or Inactive. This is the state of the exterior driver front door handle switch. |
| Ext. Rear Compartment Lid Release Sw. | - | Inactive | The scan tool displays Active or Inactive. This is the state of the exterior rear compartment release switch. |
| Ext. RF Door Handle Switch | - | Inactive | The scan tool displays Active or Inactive. This is the state of the exterior passenger front door handle switch. |
| Ignition Mode Switch | - | Idle | The scan tool displays Idle, Crank or ACC/OFF. This is the state of the ignition mode switch. |
| Int. LF Door Handle Switch | - | Inactive | The scan tool displays Active or Inactive. This is the state of the interior driver front door handle switch. |
| Int. RF Door Handle Switch | - | Inactive | The scan tool displays Active or Inactive. This is the state of the interior passenger front door handle switch. |
| Key Fob 1-4 Battery Signal | - | Varies | The scan tool displays a numeric value from 1.9-3.3 or Not Present. This is the current battery signal in the corresponding key fob. |
| Key Fob 1-4 Low Voltage | - | OK | The scan tool displays OK or Low. Low is displayed if the battery in the corresponding key fob is low. |
| Last Key Fob Used | - | Varies | The scan tool displays None, Fob 1, Fob 2, Fob 3 or Fob 4. |
| LF Pressure Sensor ID | - | Varies | This displays a numeric value. This is the driver front pressure sensor identification. |
| LF Pressure Sensor Mode | - | Varies | The scan tool displays Off, Re-measure, Wake, Drive, Learn or Low Batt. This is the current mode of the driver front pressure sensor. |
| LF Tire Press. Sensor Status | - | Normal | The scan tool displays Normal or Failed. This is the status of the driver front tire pressure sensor. |
| LF Tire Pressure | - | Varies | This displays kPa (psi). This is the current pressure in the driver front tire. |
| LR Pressure Sensor ID | - | Varies | This displays a numeric value. This is the driver rear pressure sensor identification. |
| LR Pressure Sensor Mode | - | Varies | The scan tool displays Off, Re-measure, Wake, Drive, Learn or Low Batt. This is the current mode of the driver rear pressure sensor. |
| LR Tire Press. Sensor Status | - | Normal | The scan tool displays Normal or Failed. This is the status of the driver rear tire pressure sensor. |
| LR Tire Pressure | - | Varies | This displays kPa (psi). This is the current pressure in the driver rear tire. |
| No. of Fobs Programmed | - | Varies | The scan tool displays a numeric value from 0-4. |
| RF Pressure Sensor ID | - | Varies | This displays a numeric value. This is the passenger front pressure sensor identification. |
| RF Pressure Sensor Mode | - | Varies | The scan tool displays Off, Re-measure, Wake, Drive, Learn or Low Batt. This is the current mode of the passenger front pressure sensor. |
| RF Tire Press. Sensor Status | - | Normal | The scan tool displays Normal or Failed. This is the status of the passenger front tire pressure sensor. |
| RF Tire Pressure | - | Varies | This displays kPa (psi). This is the current pressure in the passenger front tire. |
| RR Pressure Sensor ID | - | Varies | This displays a numeric value. This is the passenger rear pressure sensor identification. |
| RR Pressure Sensor Mode | - | Varies | The scan tool displays Off, Re-measure, Wake, Drive, Learn or Low Batt. This is the current mode of the passenger rear pressure sensor. |
| RR Tire Press. Sensor Status | - | Normal | The scan tool displays Normal or Failed. This is the status of the passenger rear tire pressure sensor. |
| RR Tire Pressure | - | Varies | This displays kPa (psi). This is the current pressure in the passenger rear tire. |
| Run/Crank Relay Command | - | Off | The scan tool displays On or Off. This is the state of the run/crank relay command. |
| Run/Crank Relay Status | - | Off | The scan tool displays On or Off. This is the state of the run/crank relay. |
| Sensor Learn Mode | - | Inactive | The scan tool displays Active or Inactive. Active is displayed if the tire pressure sensors are in learn mode. |
| Shift Lock Solenoid Command | - | Lock | The scan tool displays Lock or Unlock. This is the state of the shift lock solenoid command. |
| Shift Lock Solenoid Command | - | Lock | The scan tool displays Lock or Unlock. This is the state of the shift lock solenoid. |
Remote Control Door Lock Receiver Scan Tool Output Controls
| Output Control | Description |
|---|---|
| Auto. Door Unlock | This output control is used to enable or disable the automatic door unlock program into the corresponding key fob 1, 2, 3 or 4. |
| Invalidate All Fobs | This output control is used to reset all key fobs for the vehicle. |
| Key Fob in Veh. Warning | This output control is used to enable or disable the key fob in vehicle warning into the corresponding key fob 1, 2, 3 or 4. |
| Next Available Slot | This output control is used to program the next fob into the next available slot. |
| Passive Door Lock | This output control is used to enable or disable the passive door lock into the corresponding key fob 1, 2, 3 or 4. |
| Program Key Fob 1-4 | This output control is used to program the corresponding key fob 1, 2, 3 or 4. |
| Run/Crank Relay | This output control is used to command the run/crank relay ON or OFF. |
| Setup New RCDLR | This output control is used to setup a new remote control door lock receiver (RCDLR). |
| TPM Learn Mode | This output control is used to enable the tire pressure monitoring (TPM) learn mode. |