DTC P0365: Camshaft Position Sensor "B" Circuit (Bank 1); DTC P0367: Camshaft Position Sensor "B" Circuit Low Input (Bank 1); DTC P0368: Camshaft Position Sensor "B" Circuit High Input (Bank 1): Procedure

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
5. Read DTCs.

   Result

   Result	Refer to
   P0365, P0367 or P0368	A
   P0365, P0367 or P0368 and other DTCs	B

   HINT: 

   If any DTCs other than P0365, P0367 or P0368 are output, troubleshoot those DTCs first.

B → Refer to step   11 

A: Refer to next step 

1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.
   Fig 1: Identifying Camshaft Position Sensor Connector Terminals (For Exhaust Camshaft)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Turn the ignition switch to ON.
3. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   C25-3 (VC2) - Body ground	Ignition switch ON	4.5 to 5.5 V

4. Reconnect the camshaft position sensor (for exhaust camshaft) connector.

NG → Refer to step   10 

OK: Refer to next step 

1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.
   Fig 2: Identifying Camshaft Position Sensor And ECM Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Disconnect the ECM connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance (Check for Open)

   Tester Connection	Condition	Specified Condition
   C25-1 (VVE+) - C19-76 (EV1+)	Always	Below 1 Ω
   C25-2 (VVE-) - C19-75 (EV1-)	Always	Below 1 Ω

   Standard Resistance (Check for Short)

   Tester Connection	Condition	Specified Condition
   C25-1 (VVE+) or C19-76 (EV1+) - Body ground	Always	10 kΩ or higher
   C25-2 (VVE-) or C19-75 (EV1-) - Body ground	Always	10 kΩ or higher

4. Reconnect the camshaft position sensor (for exhaust camshaft) connector.
5. Reconnect the ECM connector.

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Refer to next step 

1. Check the camshaft position sensor (for exhaust camshaft) installation.
   Fig 3: Checking Sensor Installation

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   OK

   Sensor is installed correctly.

NG → Refer to step   12 

OK: Refer to next step 

1. Check the timing rotor of the exhaust camshaft.

   OK

   Camshaft timing rotor does not have any cracks or deformation.

NG → Refer to step   13 

OK: Refer to next step 

1. Replace the camshaft position sensor (for exhaust camshaft). Refer to REMOVAL .

NEXT: Refer to next step 

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Clear DTCs. Refer to DTC CHECK / CLEAR .
5. Start the engine.
6. Drive the vehicle in according with the driving pattern described in Confirmation Driving Pattern.
7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
8. Read DTCs.

   Result

   Result	Refer to
   No output	A
   P0365, P0367 or P0368	B

   HINT: 

   If the engine does not start, replace the ECM.

B → Refer to step   14 

A: Refer to next step 

Fig 4: Identifying Valve Timing Alignment Marks

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT: 

There are no marks on the cylinder head to match-up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and re-install the chain to match up the alignment marks. Refer to REASSEMBLY - Step 25 .

NEXT: Refer to next step 

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Clear DTCs. Refer to DTC CHECK / CLEAR .
5. Turn the ignition switch off.
6. Start the engine.
7. Drive the vehicle in according with the driving pattern described in Confirmation Driving Pattern.
8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
9. Read DTCs.
   RESULT
   
   

   Result	Refer to
   No output	A
   P0365, P0367 or P0368	B

   HINT: 

   If the engine does not start, replace the ECM.

B → Refer to step   14 

A → END 

1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.
   Fig 5: Identifying Camshaft Position Sensor and ECM Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Disconnect the ECM connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance (Check for Open)

   Tester Connection	Condition	Specified Condition
   C25-3 (VC2) - C19-117 (VC)	Always	Below 1 Ω

   Standard Resistance (Check for Short)

   Tester Connection	Condition	Specified Condition
   C25-3 (VC2) or C19-117 (VC) - Body ground	Always	10 kΩ or higher

4. Reconnect the camshaft position sensor (for exhaust camshaft) connector.
5. Reconnect the ECM connector.

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → Refer to step   14