Manual Transaxle Unit

MANUAL TRANSAXLE UNIT

Reverse idler gear Inside diameter	Standard	20.056 to 20.074 mm (0.7896 to 0.7903 in.)
Reverse idler gear Inside diameter	Maximum	20.074 mm (0.7903 in.)
Reverse idler gear shaft Outside diameter	Standard	19.984 to 20.000 mm (0.7868 to 0.7874 in.)
Reverse idler gear shaft Outside diameter	Maximum	19.984 mm (0.7868 in.)
Differential side bearing preload	New bearing	1.50 to 2.30 Nm (15 to 23 kgfcm, 13 to 20 in.*lbf)
Differential side bearing preload	Used bearing	0.24 to 0.37 Nm (2.4 to 3.8 kgfcm, 2.1 to 3.3 in.*lbf)
Differential side shim thickness	A	2.05 mm (0.0807 in.)
	B	2.10 mm (0.0827 in.)
	C	2.15 mm (0.0846 in.)
	D	2.20 mm (0.0866 in.)
	E	2.25 mm (0.0886 in.)
	F	2.30 mm (0.0906 in.)
	G	2.35 mm (0.0925 in.)
	H	2.40 mm (0.0945 in.)
	J	2.45 mm (0.0965 in.)
	K	2.50 mm (0.0984 in.)
	L	2.55 mm (0.100 in.)
	M	2.60 mm (0.102 in.)
	N	2.65 mm (0.104 in.)
	P	2.70 mm (0.106 in.)
	Q	2.75 mm (0.108 in.)
	R	2.80 mm (0.110 in.)
	S	2.85 mm (0.112 in.)
	T	2.90 mm (0.114 in.)
Output shaft bearing preload	New bearing	2.80 to 5.60 Nm (29 to 57 kgfcm, 25 to 50 in.*lbf)
Output shaft bearing preload	Used bearing	2.31 to 4.62 Nm (24 to 47 kgfcm, 20 to 41 in.*lbf)
Output shaft bearing shim thickness	A	1.30 mm (0.0511 in.)
	B	1.35 mm (0.0531 in.)
	C	1.40 mm (0.0551 in.)
	D	1.45 mm (0.0571 in.)
	E	1.50 mm (0.0591 in.)
	F	1.55 mm (0.0610 in.)
	G	1.60 mm (0.0630 in.)
	H	1.65 mm (0.0650 in.)
	J	1.70 mm (0.0669 in.)
	K	1.75 mm (0.0689 in.)
	L	1.80 mm (0.0709 in.)
	M	1.85 mm (0.0728 in.)
	N	1.90 mm (0.0748 in.)
	P	1.95 mm (0.0768 in.)
	Q	2.00 mm (0.0787 in.)
	R	2.05 mm (0.0807 in.)
	S	2.10 mm (0.0827 in.)
	T	2.15 mm (0.0846 in.)
	U	2.20 mm (0.0866 in.)
	V	2.25 mm (0.0886 in.)
	W	2.30 mm (0.0906 in.)
	X	2.35 mm (0.0925 in.)
	Y	2.40 mm (0.0945 in.)
	Z	2.45 mm (0.0965 in.)
	1	2.50 mm (0.0984 in.)
Outer shift lever oil seal Standard depth		0.5 to 1.0 mm (0.0197 to 0.0393 in.)
Outer No. 1 shift lever slotted spring pin Standard depth		-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)
Straight pin Protrusion height		10.5 to 11.5 mm (0.414 to 0.452 in.)
Front transaxle case oil seal Standard depth		1.0 to 2.0 mm (0.0394 to 0.0787 in.)
Rear input shaft bearing shim thickness	A	1.15 mm (0.0453 in.)
	B	1.20 mm (0.0472 in.)
	C	1.25 mm (0.0492 in.)
	D	1.30 mm (0.0512 in.)
	E	1.35 mm (0.0531 in.)
	F	1.40 mm (0.0551 in.)
	G	1.45 mm (0.0571 in.)
	H	1.50 mm (0.0591 in.)
	J	1.55 mm (0.0610 in.)
	K	1.60 mm (0.0630 in.)
	L	1.65 mm (0.0650 in.)
	M	1.70 mm (0.0669 in.)
	N	1.75 mm (0.0689 in.)
	P	1.80 mm (0.0709 in.)
Reverse shift fork slotted spring pin Standard depth		-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)
Outer select lever oil seal Standard depth		0.5 to 1.0 mm (0.0197 to 0.0393 in.)