How To Proceed With Troubleshooting [06/2015 - ]: Procedure

Result

Result:  1

NEXT 

See step  2

1. Refer to How to Troubleshoot ECU Controlled Systems in Introduction.

   Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2015 - ]

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

See step  3

Standard Voltage

11 to 14 V

HINT: 

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

Result

Result:  1

NEXT 

See step  4

1. Using the Techstream, check if the CAN communication system is functioning normally.

   CAN Bus Check 

   HINT: 

   • Refer to CAN Bus Check in CAN Communication System.

     Refer to DIAGNOSIS SYSTEM [06/2015 - ]

   • The ECM is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there are no malfunctions in the CAN communications system.

   Result

   Result	Proceed to
   CAN communication system DTCs are not output.	A
   CAN communication system DTCs are output.	B

Result:  2

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2015 - ] 

Result:  1

A 

See step  5

1. Refer to DTC Check/Clear.

   Refer to DTC CHECK / CLEAR [06/2015 - ] 

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

See step  6

1. Refer to Check Mode Procedure.

   Refer to CHECK MODE PROCEDURE [06/2015 - ] 

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

See step  7

1. Proceed to DTC Check/Clear.

   Refer to DTC CHECK / CLEAR [06/2015 - ] 

   Powertrain > Engine and ECT > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output.	A
   DTCs are output.	B

Result:  2

B 

See step  14

Result:  1

A 

See step  8

1. Refer to Continuously Variable Transaxle Fluid.

   Refer to ADJUSTMENT [06/2015 - ]

2. Refer to Park/Neutral Position Switch.

   Refer to ON-VEHICLE INSPECTION [06/2015 - ]

3. Refer to Shift Lever.

   Refer to ON-VEHICLE INSPECTION [06/2015 - ]

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

See step  11

Result:  1

OK 

See step  9

1. Refer to Road Test.

   Refer to ROAD TEST [06/2015 - ] 

2. Refer to Mechanical System Tests.

   Refer to MECHANICAL SYSTEM TESTS [06/2015 - ] 

3. Refer to Hydraulic Test.

   Refer to HYDRAULIC TEST [06/2015 - ] 

   Result

   Result	Proceed to
   Symptom does not occur	A
   Symptom occurs	B

Result:  2

B 

See step  11

Result:  1

A 

See step  10

1. Refer to Symptom Simulation.

   Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2015 - ]

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

See step  11

Result

Result:  1

NEXT 

See step  12

Result

Result:  1

NEXT 

See step  13

Result

Result:  1

NEXT 

END 

1. Proceed to Diagnostic Trouble Code Chart.

   Refer to DIAGNOSTIC TROUBLE CODE CHART [06/2015 - ] 

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

See step  15

Result

Result:  1

NEXT 

See step  16

Result

Result:  1

NEXT 

See step  17

Result

Result:  1

NEXT 

See step  18

Result

Result:  1

NEXT 

END