LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2006 >> B9 Tribeca Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Communication Devices >> LAN System (Diagnostics) >> Subaru Select Monitor >> Operation >> Function Setting (ECM Customizing)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Function Setting (ECM Customizing)

  1. On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key.
  2. On the «System Selection Menu» display screen, select the {Integ. Unit mode} and press the [YES] key.
  3. On the «Integ. Unit mode failure diag» display screen, select the {ECM customizing} and press the [YES] key.
  4. Change the setting with UP/DOWN key and press the [YES] key.
    • List of function setting item (ECM customizing)
    NOTE: Even if changes are made to items that are not equipped, the contents are not confirmed and do not operate.
    DISPLAY CONTENTS

    Data Initial setting value Customize setting Remarks Destination Specifications
    Off delay time Normal   Delay time below can be selected by setting.  
    After door closed After key unlock
    OFF 0 sec. 0 sec.
    Short 3 sec. 10 sec.
    Normal 5 sec. 20 sec.
    Long 8 sec. 30 sec.
    Auto lock time 30 sec. 0 - 60 sec. Workable when Auto locking is set to "ON" and Automatic locking setup is "ON". Time can be changed by 10 seconds: 0 (OFF) - 60 (maximum). Not supported by North American specifications
    Rr defogger op. mode 15 min. 15 min. Rear defogger stops in 15 minutes automatically after switch is turned to ON.  
    Continuous Rear defogger repeats active condition for 15 minutes and inactive condition for 2 minutes until switch is turned to OFF.
    Wiper deicer op. mode 15 min. 15 min. Wiper deicer stops in 15 minutes automatically after switch is turned to ON.  
    Continuous Wiper deicer repeats active condition for 15 minutes and inactive condition for 2 minutes until switch is turned to OFF.
    Security Alarm Setup ON ON Security alarm (hazard, horn or siren) in active condition  
    OFF Security alarm in inactive condition
    Impact Sensor Setup OFF ON Workable when Impact Sensor Setup is set to "ON" Impact sensor in active condition  
    OFF Impact sensor in inactive condition (Set Impact Sensor Setup of model without impact sensor to "OFF".)
    Alarm monitor delay setting ON   After doors are locked by keyless entry system operated, Alarm monitor starts in following time.  
    ON Delay time is 30 seconds.
    OFF Delay time is 0 seconds.
    Lockout prevention ON ON Lockout prevention in inactive condition (Lockout prevention does not operate if safety knob is locked by hand.)  
    OFF Lockout prevention in inactive condition
    Impact Sensor OFF ON Vehicle is controlled in impact sensor equipped mode. (Set impact sensor to "OFF" in model without impact sensor. If impact sensor is set to "ON", hazard, horn or siren operate after doors are locked by keyless entry system operated (Alarm monitor starting). Set to "ON" when an optional impact sensor is installed.
    OFF Vehicle is controlled in impact sensor no-equipped mode.
    Siren setting OFF ON Siren sounds when alarm operates. (Set siren setting to "OFF" in model without siren. Horn does not sound if siren setting is set to "ON".) Set to "ON" when an optional siren is installed.
    OFF Horn sounds when alarm operates.
    Answer-back buzzer setup ON ON Workable when answer-back buzzer setup is set to "ON". When lock/unlock is selected by keyless entry system operated, hazard answer-back buzzer operates.  
    OFF When lock/unlock is selected by keyless entry system operated, answer-back buzzer does not sound.
    Hazard answerback setup ON ON Workable when hazard answer-back setup is set to "ON." When lock/unlock is selected by keyless entry system operated, hazard answer-back buzzer operates.  
    OFF When lock/unlock is selected by keyless entry system operated, hazard answer-back does not operate.
    Automatic locking setup ON ON Workable when Automatic locking setup is set to "ON" Automatic locking operates. Not supported by North American specifications
    OFF Automatic locking does not operate.
    Ans.-back Buzzer ON ON Vehicle is controlled in answer-back buzzer equipped mode. Not supported by North American specifications
    OFF Vehicle is controlled in answer-back buzzer non-equipped mode. (Set Ans.-back Buzzer to "OFF" in model without answer back buzzer.)
    Auto locking ON ON Vehicle is controlled in auto locking equipped mode. Not supported by North American specifications
    OFF Vehicle is controlled in auto locking non-equipped mode. (Set Auto locking to "OFF" in model without auto locking.)
    Initial Keyless Setting - - -  
    Execution Settings of keyless entry system are initialized. (Auto-lock time: 30 sec, Answer-back buzzer setup: ON, Hazard answer-back setup: ON, Automatic locking setup: ON, Ans.-back Buzzer: ON)
    Initial button setting - - -  
    Execution Settings of each function are initialized. (Off delay time: Normal, Rr defogger op. mode: 15 min., Wiper deicer op. mode: 15 min., Lockout prevention: ON)
    Initial Security setting - - - Not supported by North American specifications
    Execution Settings of security system are initialized. (Security Alarm Setup: OFF, Impact Sensor Setup: OFF, Alarm monitor delay setting: ON, Siren setting: OFF)
    Passive Alarm (Not used) OFF ON Workable when passive arming is set to "ON."  
    OFF
    Door open warning (prevention of battery run-out) OFF ON If detecting door open for 30 minutes, room light, key illumination and door warning light are turned off to prevent battery run-out.  
    OFF Room light, key illumination and door warning light is not turned off.
    Alarm interlocked room light switch OFF ON The room light lights by being interlocked with the activation of the alarm.  
    OFF Room light does not illuminate even if the alarm is activated.
  5. After setting, make sure that vehicle equipment is same as the setting changed in the {Current Data Display & Save}.
    CAUTION:
    • It is possible to control the original functions of vehicle when settings above are corresponded to vehicle equipment.
    • Do not change the settings except for setting above during operation of equipment setting.
    • Be sure not to change Factory initial setting except installation of new body integrated unit.
    NOTE: For details concerning operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL ".