| B2271 |
[IGN fuse blown-out or IGN circuit failure] |
Turn the engine switch on (IG). |
|
| B2274 |
[ACC circuit abnormal] |
Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off. |
|
| B2275 |
[STSW circuit abnormal] |
Start the engine. |
|
| B2276 |
[ACCR signal abnormal] |
Start the engine. |
|
| B2277 |
[Submerging circuit abnormal] |
Submerging circuit monitor result = ON |
|
| B2282 |
[Vehicle speed signal abnormal] |
Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16MPH) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h {3MPH} for 20 seconds. |
|
| B2283 |
[Vehicle speed sensor fault detection] |
In IG ON, any of the following conditions is established.
- Direct connection vehicle speed pulse showing 50 km/h or more continues for 10 seconds, then the CAN and direct connection speed pulses both turn to 0 km/h within 1 second.
- In an AT vehicle, CAN and the direct connection show 0 km/h, the engine speed (according to the direct connection) is 2000 r/min or more, the shift lever is not in P or N, and ACCR is not in LOW level for 300 seconds.
- In an MT vehicle, CAN and the direct connection show 0 km/h, the engine speed (according to the direct connection) is 2000 r/min or more, the N position for the shift lever is OFF, the clutch switch is OFF, and ACCR is in the LOW level for 300 seconds.
|
|
| B2284 |
[Brake Signal (Cable-Information does not match to BEAN-Information)] |
Connect the cable to the negative (-) battery terminal, release the brake pedal and wait 20 seconds or more. Then depress the brake pedal for 20 seconds or more. |
|
| B2285 |
[Steering lock position signal abnormal] |
Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) battery terminal. Wait 40 seconds or more with the engine switch off (with the steering wheel locked), then turn the engine switch on (ACC) (with the steering wheel unlocked) and wait 40 seconds or more. |
|
| B2286 |
[Run able Signal (Cable-Information does not match to BEAN-Information)] |
Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait 20 seconds or more with the engine switch off, then start the engine and maintain an engine speed of 1000 r/min or more for 20 seconds or more after starting the engine. |
|
| U0073 |
[Control Module Communication Bus "A" Off] |
10 or more seconds have passed after IG ON |
|
| U0100 |
[Lost Communication With ECM/PCM "A"] |
10 or more seconds have passed after IG ON |
|
| U0101 |
[Lost Communication With |
TCM] 10 or more seconds have passed after IG ON |
|
| U0122 |
[Lost Communication With Vehicle Dynamics Control Module] |
10 or more seconds have passed after IG ON |
|
| U0140 |
[Lost Communication With Body Control Module] |
10 or more seconds have passed after IG ON |
|
| U0155 |
[Lost Communication With Instrument Panel Cluster (IPC) Control Module] |
10 or more seconds have passed after IG ON |
|
| U0401 |
[Invalid Data Received From ECM/PCM "A"] |
10 or more seconds have passed after IG ON |
|
| U0422 |
[Invalid Data Received From Body Control Module] |
10 or more seconds have passed after IG ON |
|