LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2013 >> Outback Base, Standard Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 39 (LAN Communication System (Diagnostics)) >> Registration Body Integrated Unit >> Operation >> Registration Body Integrated Unit (Function Setting)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Registration Body Integrated Unit (Function Setting)

WARNING: This page is about a different car, the 2013 Subaru Forester. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: Body integrated unit is core of LAN system, and also can select the function of all vehicle system control. It is possible to control the original functions of vehicle when registrations of body integrated unit and function setting are corresponded to vehicle equipment.
If registrations and function setting are different from vehicle equipment, vehicle system does not operate normally and diagnosis cannot be performed correctly. Pay attention to following item.
  • Be sure to correspond registrations and function settings to vehicle equipment.
  • Do not change the settings of vehicle improperly.
  • Confirm that key illumination does not blink when ignition switch is turned ON, or "Factory initial setting" of body integrated unit registrations is set to "Market". If "Factory initial setting" is set to "Factory", key illumination blinks when the ignition switch is turned ON, to notify that the settings are not confirmed.
  • Key illumination does not blink with ignition switch turned to ON and go off with door closed.
  • Be sure to register immobilizer if body integrated unit is replaced with a new part. (model with immobilizer)
  • Make a registration of immobilizer when the parts related to immobilizer have been replaced. Refer to the "REGISTRATION MANUAL FOR IMMOBILIZER".
  1. On «Main Menu» display, select {Each System Check}.
  2. On «System Selection Menu» display, select {Integ. unit mode}.
  3. Click the [OK] button after the control module name (integrated unit) is displayed.
  4. On «Integ. unit mode failure diag.» display, select {Unit customizing}.
  5. Change the setting with UP/DOWN key.
    • List of body integrated unit registration item
    NOTE: Setting is different depending on the grade of vehicle.
    Data Initial setting Registration Remarks
    Map lamp 30 sec off record No Support Support Set to "OFF" for models with door interlock switch in map light, "ON" for models without door interlock switch.
    No Support
    A/C ECM setting No Support Support Set to "ON" in case of model with auto A/C. Set to "OFF" in case of model without auto A/C.
    No Support
    wiperdeicer (factory option) No Support Support ON signal does not output with operation of wiper deicer switch if wiper deicer is set to "OFF" in models with a wiper deicer.
    No Support
    Sedan/Wagon Setting Wagon Wagon Door lock/unlock control by Wagon
    Sedan Door lock/unlock control by Sedan
    MT/AT Setting AT MT No control of shift lock solenoid, key-lock solenoid
    AT Control of shift lock solenoid, key-lock solenoid
    6MT Setting Other than 6MT 6MT Set "6MT" for 6MT model, and set "Other than 6MT" for AT/5AT model.
    Other than 6MT
    Factory initial setting Factory Factory Be sure to set to "Market". After setting change, turn the ignition switch to OFF and settle the changed settings.
    Market (Confirmed)
    CAUTION:
    • To perform normal operation of vehicle and diagnosis, the above settings must match the actual vehicle equipment.
    • When body integrated unit is a new part or "Factory" mode, key illumination blinks to show equipment settings have not been completed. Check the detailed procedures of function setting.
    • Be sure not to change Factory initial setting except when installing a new body integrated unit.
    NOTE: "Factory" mode:
    • Body integrated unit has not been set yet. It can be recognized by key illumination blinking with ignition switch turned to ON.
    • All replacement body integrated units are set to "Factory" mode. When replacing a body integrated unit, be sure to perform the registration operation.

    "Market" mode:

    • Each settings have been set. It can be recognized by key ring illumination coming on in concocting with room light and going off with ignition switch turned to ON.
  6. Perform the Factory initial setting. On the «Unit customizing» display screen of Subaru Select Monitor, select the {Factory initial setting}.
  7. Change the mode from Factory to Market.
  8. Turn the ignition switch to OFF to settle the setting.
  9. Change the Subaru Select Monitor system selection to «Immobilizer» to register the immobilizer key.
  10. Perform the registration according to the procedures of the "REGISTRATION MANUAL FOR IMMOBILIZER".
  11. When key registration is completed, "Do you want to register remote engine start?" is displayed. Perform registration only for equipped models.
  12. Perform the User Customizing.< Refer to OPERATION , User Customizing. >
    NOTE: For detailed operation procedures, refer to "PC application help for Subaru Select Monitor".
scientia non olet · About LEMON Manuals