LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2015 >> BRZ Limited, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 8 (Lin Communication System) >> Large-Scale Multiplex Communication System For Vehicle Body [LIN] >> DTC B2785 LIN Communication Error >> Inspection steps
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Inspection steps

WARNING: This page is about a different car, the 2014 Subaru BRZ. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: To replace the collation ECM (Smart key computer ASSY), the steering lock actuator ASSY, and the ID code box, refer to the procedure for engine immobilizer system registration.
  1. Clear diagnostic code
    1. Clear the diagnostic code using the SSM3. (Refer to CHECKING/CLEARING DIAGNOSTIC CODES  )

      Next

  2. DTC check
    1. Use SSM3 to check DTC output. (Refer to CHECKING/CLEARING DIAGNOSTIC CODES  )
      RESULT

      Result Go to
      B2785 is output A
      B2785 is not output B

      B: Go to "How to simulate trouble phenomenon". (Refer to PROCEDURES FOR MALFUNCTION PHENOMENON SIMULATION )

      A: Go to Next Step

  3. Check the LIN communication line (Collation ECM (Smart key computer ASSY) - Steering lock actuator ASSY)
    1. Disconnect the connector D41 from the collation ECM (Smart key computer ASSY).
    2. Disconnect the connector D59 from the steering lock actuator ASSY.
    3. Disconnect the connector A30 from the ID code box (Immobilizer code ECM)*.
    4. Measure the resistance between the terminals.
      RESISTANCE (OPEN CIRCUIT CHECK)

      Inspection terminals Inspection conditions Standard value
      D41-17-D59-5 Always Less than 1 Ω
      D41-17-A30-2* Always Less than 1 Ω
      RESISTANCE (SHORT CIRCUIT CHECK)

      Inspection terminals Inspection conditions Standard value
      D41-17 - chassis ground Always 10 kΩ or more
      D59-5 - chassis ground Always 10 kΩ or more
      A30-2 - chassis ground* Always 10 kΩ or more
    5. Reconnect the connector D41 to the collation ECM (Smart key computer ASSY).

      *: with ID code box

      NG: Repair or replacement of wiring harness or connector

      OK: Go to Next Step

  4. DTC check (Steering lock actuator ASSY)
    1. Check DTC using SSM3. (Refer to CHECKING/CLEARING DIAGNOSTIC CODES  )
      RESULT

      Result Go to
      B2785 is not output A
      B2785 is output B
    2. Reconnect the connector D59 to the steering lock actuator ASSY.

      B: Replace the collation ECM (Smart key computer ASSY)

      A: Go to Next Step

  5. Replace the steering lock actuator ASSY connector or ID code box (with ID code box)
    1. Replace the collation ECM (Smart key computer ASSY) or ID code box* with a new part.
    2. Clear the diagnostic code using the SSM3. (Refer to CHECKING/CLEARING DIAGNOSTIC CODES  )

      *: with ID code box

      Next

  6. Recheck the diagnostic codes.
    1. Using SSM3, check the diagnostic code again. (Refer to CHECKING/CLEARING DIAGNOSTIC CODES  )
      RESULT

      Result Go to
      B2785 is not output A
      B2785 is output B

      B: Replace the collation ECM (Smart key computer ASSY)

      A: Complete (Failure of the steering lock actuator ASSY connector or ID code box (with ID code box))

scientia non olet · About LEMON Manuals