Current Data Display & Save/System Operation Check Mode

Read data list

CAUTION: The values indicated under the normal conditions in the table below are informative values. Do not depend on reference value only when judging if the part is faulty.

NOTE: By using the SSM3 for reading the data list, it is able to read the values and the status of the switches, sensors, or actuators without removing these parts. This inspection is very useful because it allows an operator to read any intermittent conditions or signals without disturbing parts or wiring. By reading the current data display & save information at an initial phase of troubleshooting, you can save time for diagnosis.

Connect the SSM3 to the DLC3.
Turn IG SW to ON.
Turn on the SSM3.
Enter the following menus. [Integ. unit mode] →[Current Data Display & Save]

Using SSM3, read the data list according to the screen displays.

Main body ECM

MAIN BODY ECM TESTER DISPLAY REFERENCE

Tester display	Measurement items/range	Normal condition	Notes for diagnosis
[D Door Courtesy]	Driver's door courtesy light switch signal/ON or OFF	ON: Driver's door is open OFF: Driver's door is closed	-
[P Door Courtesy]	Passenger's door courtesy light switch signal/ON or OFF	ON: Passenger's door is open OFF: Passenger's door is closed	-
[Luggage Courtesy SW]	Trunk courtesy switch signal/OFF or ON	ON: The trunk is open. OFF: Trunk is closed	-
[Ignition]	Ignition switch IG signal/ON or OFF	ON: IG SW ON OFF: IG SW OFF	-
[ACC SW]	Ignition switch ACC signal/ON or OFF	ON: IG SW ACC OFF: IG SW OFF	-
[Key Unlock Warning SW]	Unlock warning switch/OFF or ON	OFF: Ignition key is not inserted ON: Ignition key is inserted	-
[Keyless Control]	Yes or No	Customized setting display	-
[Wireless Buzzer Resp]	Wireless buzzer response/OFF or ON	Customized setting display	-
[Hazard Answer Back]	Wireless hazard answer-back/OFF or ON	Customized setting display	-
[Open Door Warning]	Open door warning/OFF or ON	Customized setting display	-
[Unloocking operation]	Yes or No	Customized setting display	-
[Panic Alarm Function]	Panic function/OFF or ON	Customized setting display	-
[Wireless Auto Lock]	Auto lock function/OFF or ON	Customized setting display	-
[Auto Lock Time]	Auto look time/30 seconds, 60 seconds, 120 seconds	Customized setting display	-
[Trunk lid unlocking operation]	single press/2times ON/Long press (short)/Long press (long)	Customized setting display	-
[Wireless Buzzer Volume]	Wireless door lock buzzer vol/Level7, Level6, Level5, Level4, Level3, Level2, Level1, or Level0	Customized setting display	-

Perform system operation check mode

NOTE: If SSM3 is used for executing the system operation check mode, the relays, VSV, actuators and other components can be operated without removing parts. This functional inspection method is very useful because it helps check state-related signals and identify the faulty part without removing any parts and wiring. By performing active tests at an initial phase of troubleshooting, you can save time for diagnosis. The current data display & save information can be displayed during system operation check mode.

Connect the SSM3 to the DLC3.
Turn IG SW to ON.
Turn on the SSM3.
Enter the following menus. [Integ. unit mode] →[Work Support]→[System Operation Check Mode]

Execute the system operation check mode according to the SSM3 display.

Main body

MAIN BODY TESTER DISPLAY REFERENCE

Tester display	Tested parts	Control range	Notes for diagnosis
[Door Lock]	Door lock motor	[Lock]/[Unlock]	-
[D-Door Unlock]	Driver's door lock motor	OFF/ON	-
[Trunk and Back-Door Open]	Trunk lock motor	OFF/ON	-
[Illuminated Entry System]	Room light (room light switch is set to door position and all doors are closed)	OFF/ON	-
[Keyless Buzzer Output]	Wireless door lock buzzer	OFF/ON	-