Power Window Control Switch: Inspection: Sub-Switch

SWITCH POWER WINDOW SUB FRONT 

1. Measure the resistance between terminals of the switch power window sub front.

   Preparation tool: 

   Circuit tester

   • Base grade

   Courtesy of SUBARU OF AMERICA, INC.

   Terminal No.	Inspection conditions	Standard
   1 - 2 5 - 4	OFF	Less than 1 Ω
   2 - 3 3 - 4 1 - 3 3 - 5		1 MΩ or more
   3 - 2 5 - 4	Manual UP	Less than 1 Ω
   1 - 2		1 MΩ or more
   1 - 2 3 - 4	Manual DOWN	Less than 1 Ω
   4 - 5		1 MΩ or more

   • Other than base grade

   Courtesy of SUBARU OF AMERICA, INC.

   Terminal No.	Inspection conditions	Standard
   6 - 5	OFF	Less than 1 Ω
   2 - 1 2 - 5 2 - 6		1 MΩ or more
   2 - 6	Manual UP	Less than 1 Ω
   5 - 6 2 - 5 1 - 2		1 MΩ or more
   2 - 6 1 - 2	Auto UP	Less than 1 Ω
   5 - 6 2 - 5		1 MΩ or more
   2 - 5	Manual DOWN	Less than 1 Ω
   5 - 6 2 - 6 1 - 2		1 MΩ or more
   2 - 5 1 - 2	Auto DOWN	Less than 1 Ω
   5 - 6 2 - 6		1 MΩ or more

2. Apply battery voltage between the switch power window sub front terminals to check lighting condition of illumination inside the switch.
   CAUTION: When applying battery voltage, do not mix up the positive (+) side and the negative (-) side.
   CAUTION: Incorrect polarity connection may cause LED damage inside the switch.
   • Base grade

   Terminal No.	Inspection conditions	Standard
   3 (+) - 1 (-) 3 (+) - 5 (-)	Apply battery voltage.	Light ON

   • Other than base grade

   Terminal No.	Inspection conditions	Standard
   7 (+) - 2 (-)	Apply battery voltage.	Light ON

3. Replace the switch power window sub front if it is found defective from the inspection result.

SWITCH POWER WINDOW SUB REAR 

1. Measure the resistance between terminals of the switch power window sub rear.

   Preparation tool: 

   Circuit tester

   • Base grade, except for base grade (model without telematics)

   Courtesy of SUBARU OF AMERICA, INC.

   Terminal No.	Inspection conditions	Standard
   1 - 2 5 - 4	OFF	Less than 1 Ω
   2 - 3 3 - 4 1 - 3 3 - 5		1 MΩ or more
   3 - 2 5 - 4	Manual UP	Less than 1 Ω
   1 - 2		1 MΩ or more
   1 - 2 3 - 4	Manual DOWN	Less than 1 Ω
   4 - 5		1 MΩ or more

   • Except for base grade (model with telematics)

   Courtesy of SUBARU OF AMERICA, INC.

   Terminal No.	Inspection conditions	Standard
   5 - 6	OFF	Less than 1 Ω
   2 - 5 2 - 6		1 MΩ or more
   2 - 6	Manual UP	Less than 1 Ω
   5 - 6 2 - 5		1 MΩ or more
   2 - 5	Manual DOWN	Less than 1 Ω
   5 - 6 2 - 6		1 MΩ or more

2. Apply battery voltage between the switch power window sub rear terminals to check lighting condition of illumination inside the switch.
   CAUTION: When applying battery voltage, do not mix up the positive (+) side and the negative (-) side.
   CAUTION: Incorrect polarity connection may cause LED damage inside the switch.
   • Base grade, except for base grade (model without telematics)

   Terminal No.	Inspection conditions	Standard
   3 (+) - 1 (-) 3 (+) - 5 (-)	Apply battery voltage.	Light ON

   • Except for base grade (model with telematics)

   Terminal No.	Inspection conditions	Standard
   7 (+) - 2 (-)	Apply battery voltage.	Light ON

3. Replace the switch power window sub rear if it is found defective from the inspection result.