LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2003 >> Highlander Base, 3.0 F, FWD >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission Floor Shift Control Cable Assembly >> Replacement
October 30: LEMON manuals on a temporary server, it is slow and having issues, download the manuals you need! Later in November we will switch back to the fast server.

Automatic Transmission Floor Shift Control Cable Assembly: Replacement

  1. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSY CENTER (See  REPLACEMENT  ) 
  2. REMOVE FLOOR CARPET COVER CENTER RH (See  REPLACEMENT  ) 
  3. REMOVE FLOOR CARPET COVER CENTER LH (See  REPLACEMENT  ) 
  4. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER (See  REPLACEMENT  ) 
  5. REMOVE BATTERY 
  6. REMOVE AIR CLEANER ASSY 
  7. REMOVE AIR CLEANER HOSE NO. 1 
  8. REMOVE FLOOR SHIFT TRANSMISSION CONTROL CABLE ASSY 
    1. Remove the nut from the control shaft lever.
      Fig 1: Removing Nut From Control Shaft Lever
      G02859212Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the control cable from the control shaft lever.
    3. Remove the clip and disconnect the control cable from the control cable bracket.
      Fig 2: Removing Clip And Disconnecting Control Cable
      G02859213Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disconnect the control cable from the control cable clamp.
      Fig 3: Disconnecting Control Cable
      G02859214Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disconnect the cable end from the rod of the floor shift assy.
      Fig 4: Removing Cable End
      G02859215Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the 2 nuts.
      Fig 5: Removing Nuts
      G02859216Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Remove the 3 bolts.
    8. Pull out the control cable from the body.
      Fig 6: Removing Control Cable From Body
      G02859217Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. INSTALL FLOOR SHIFT TRANSMISSION CONTROL CABLE ASSY 
    1. Pull in the control cable to the body.
    2. Install the 3 bolts.

      Torque: 4.9 N.m (50 kgf.cm, 43 in.lbf) 

      Fig 7: Installing Control Cable To Body
      G02859218Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the cable end, as shown in Fig 8.
      Fig 8: Installing Cable End
      G02859219Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: Install it with the uneven surface facing up.
    4. Install the control cable and 2 nuts.
      Fig 9: Installing Control Cable Nuts
      G02859220Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 11.8 N.m (122 kgf.cm, 9 ft.lbf) 

    5. Connect the control cable to the control cable clamp.
      Fig 10: Connecting Control Cable
      G02859221Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Temporarily install the control cable to the control shaft lever with nuts.
      Fig 11: Installing Control Cable
      G02859222Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Install the control cable and clip to the bracket.
      Fig 12: Installing Control Cable And Clip To Bracket
      G02859223Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. INSTALL AIR CLEANER ASSY 
  11. ADJUST SHIFT LEVER POSITION (See  ADJUSTMENT  ) 
  12. INSPECT SHIFT LEVER POSITION (See  ADJUSTMENT  ) 
scientia non olet · About LEMON Manuals