LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2007 >> FJ Cruiser 4WD, Part Time >> Repair and Diagnosis >> Body & Frame >> Windows >> Windshield/Window Glass >> Power Window Control System >> Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch >> Inspection Procedure
October 30: LEMON manuals on a temporary server, it is slow and having issues, download the manuals you need! Later in November we will switch back to the fast server.

Inspection Procedure

  1. CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) (POWER SOURCE) 
    1. Disconnect the G6 regulator switch connector.
      Fig 1: Identifying G6 Regulator Switch Connector Terminals
      G05114286Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the voltage of the wire harness side connector.

      Standard voltage 

      STANDARD VOLTAGE SPECIFICATIONS

      Tester Connection Condition Specified Condition
      G6-4 - Body ground Ignition switch ON 11 to 14 V
    3. Reconnect the switch connector.

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go TO NEXT STEP 

  2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) 
    1. Remove the power window regulator switch.
      Fig 2: Identifying Power Window Regulator Switch Connector Terminals
      G05114287Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the resistance.

      Standard resistance 

      STANDARD RESISTANCE SPECIFICATIONS

      Tester Connection Switch Condition Specified Condition
      1-2
      3-4      		 UP Below 1 Ω
      1-2
      3-5      		 OFF Below 1 Ω
      1-4
      3-5      		 DOWN Below 1 Ω
    3. Reinstall the switch.

    NG: REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) 

    OK: GO TO NEXT STEP 

  3. CHECK HARNESS AND CONNECTOR (SWITCH (PASSENGER SIDE) - MOTOR (PASSENGER SIDE)) 
    1. Disconnect the G6 power window regulator switch connector.
    2. Disconnect the G3 power window regulator motor connector.
      Fig 3: Identifying G6 & G3 Power Window Regulator Switch Connector Terminals
      G05114288Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Check the resistance.

      Standard resistance 

      STANDARD RESISTANCE SPECIFICATIONS

      Tester Connection Specified Condition
      G6-3 - G3-2 Below 1 Ω
      G6-1 - G3-1 Below 1 Ω
      G6-3 or G3-2 - Body ground 10 kΩ or higher
      G6-1 or G3-1 - Body ground 10 kΩ or higher
    4. Reconnect the motor connector.
    5. Reconnect the switch connector.

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go TO NEXT STEP 

  4. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE) 
    1. Remove the power window regulator motor.
    2. Apply battery voltage to connector terminals 1 and 2.
      NOTE: Do not apply battery voltage to any terminals except terminals 1 and 2.
    3. Check that the motor gear rotates smoothly as follows.

      OK: 

      MEASUREMENT CONDITION AND SPECIFIED CONDITION

      Measurement Condition Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2      		 Motor gear rotates clockwise
      Battery positive (+) → 2
      Battery negative (-) → 1      		 Motor gear rotates counterclockwise
      Fig 4: Checking Motor Gear Rotation
      G04833769Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Reinstall the motor.

    NG: REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE) 

    OK: Go TO NEXT STEP 

  5. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (PASSENGER SIDE)) 
    1. Disconnect the H5 power window regulator master switch connector.
    2. Disconnect the G6 power window regulator switch connector.
      3. Fig 5: Identifying G6 & H5 Power Window Regulator Master Switch Connector
      G05114290Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Check the resistance.

      Standard resistance 

      STANDARD RESISTANCE SPECIFICATIONS

      Tester Connection Specified Condition
      H5-8 (PU) - G6-5 Below 1 Ω
      H5-10 (PD) - G6-2 Below 1 Ω
      H5-8 (PU) or G6-5 - Body ground 10 kΩ or higher
      H5-10 (PD) or G6-2 - Body ground 10 kΩ or higher
    4. Reconnect the switch connector.
    5. Reconnect the master switch connector.

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go TO NEXT STEP 

  6. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (FRONT PASSENGER SWITCH) 
    1. Remove the power window regulator master switch.
    2. Check the resistance.
      Fig 6: Identifying Power Window Regulator Master Switch
      G05114291Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard resistance 

      STANDARD RESISTANCE SPECIFICATIONS

      Window Lock Switch Condition Power Window Switch Condition Tester Connection Specified Condition
      OFF UP 1 (E) - 10 (PD)
      8 (PU) - 9 (B)      		 Below 1 Ω
      OFF OFF 1 (E) - 8 (PU)
      1 (E) - 10 (PD)      		 Below 1 Ω
      OFF DOWN 1 (E) - 8 (PU)
      9 (B) - 10 (PD)      		 Below 1 Ω
      ON UP 1 (E) - 10 (PD) 10 kΩ or higher
      8 (PU) - 9 (B) Below 1 Ω
      ON OFF 8 (PU) - 10 (PD) Below 1 Ω
      ON DOWN 1 (E) - 8 (PU) 10 kΩ or higher
      9 (B) - 10 (PD) Below 1 Ω
    3. Reinstall the master switch.

    NG: REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY 

    OK: GO TO SYSTEM IS OK 

scientia non olet · About LEMON Manuals