LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2009 >> Corolla XRS, Automatic >> Repair and Diagnosis >> General Information >> Identification >> Introduction >> Repair Instruction >> Customize Parameters
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Customize Parameters

HINT:

The following items can be customized.

NOTE:
  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.
  1. POWER DOOR LOCK CONTROL SYSTEM 

    Main Body 

    MAIN BODY REFERENCE

    Tester Display Default Content Setting
    Unlock Key Twice ON Function that unlocks only driver side door when driver side door key cylinder is turned to UNLOCK once, and unlock all doors when it is turned to UNLOCK twice. For OFF setting, turning it once unlocks all doors. ON/OFF
    Auto Lock/Shift(1) ON Function that locks all doors when shift lever is shifted from P to any other position with engine running and all doors closed ON/OFF
    Auto Unlock/Shift(1) ON Function that unlocks all doors when shift lever is shifted to P from any other position while the ignition switch is ON ON/OFF
    All Unlock/Open-Close OFF Function that unlocks all doors when opening driver door within 10 seconds after turning the ignition switch is OFF ON/OFF
    Auto Lock OFF Function that locks all doors when vehicle speed reaches a certain level ON/OFF
    (1) for A/T
  2. WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System) 

    Wireless Door Lock Control System 

    WIRELESS DOOR LOCK CONTROL SYSTEM REFERENCE

    Display (item) Default Function Setting
    Wireless Control ON Function that turns wireless door lock function ON/OFF ON/OFF
    Hazard Answer Back ON
    • When the doors are locked by wireless operation, the hazard warning lights flash once.
    • When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
    		 ON/OFF
    Wireless Buzzer Resp ON Wireless door lock buzzer response / ON or OFF ON/OFF
    Open Door Warning ON The buzzer sounds when LOCK is pressed when any of the doors are ajar. ON/OFF
    Unlock 2 Operation ON Function that unlocks driver side door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. ON/OFF
    Panic Function ON Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds ON/OFF
    Trunk Lid Operation 0.8 s This function changes operation method of transmitter to open luggage compartment door.
    1 tim ON: Push once
    2 tim ON: Push twice
    0.8 s: Push and hold for 0.8 seconds
    Prohibit: Does not operate    		 1 tim ON / 2 tim ON / 0.8 s / Prohibit
    Auto Lock Time 60s This function regulates the interval between unlocking and automatic relocking of doors. 30 s/60 s/120 s
  3. WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System) 

    Wireless Door Lock Control System 

    WIRELESS DOOR LOCK CONTROL SYSTEM REFERENCE

    Display (item) Default Function Setting
    Wireless Control ON Function that turns wireless door lock function ON/OFF ON/OFF
    Hazard Answer Back ON
    • When the doors are locked by wireless operation, the hazard warning lights flash once.
    • When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
    		 ON/OFF
    Wireless Buzzer Resp ON Wireless door lock buzzer response / ON or OFF ON/OFF
    Open Door Warning ON The buzzer sounds when LOCK is pressed when any of the doors are ajar. ON/OFF
    Unlock 2 Operation ON Function that unlocks driver side door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. ON/OFF
    Panic Function ON Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds ON/OFF
    Trunk Lid Operation 0.6 s This function changes operation method of transmitter to open luggage compartment door.
    1 tim ON: Push once
    2 tim ON: Push twice
    0.6 s: Push and hold for 0.6 seconds
    1.6 s: Push and hold for 1.6 seconds
    Prohibit: Does not operate    		 1 tim ON / 2 tim ON / 0.6 s / 1.6 s / Prohibit
    Auto Lock Time 60s This function regulates the interval between unlocking and automatic relocking of doors. 30 s/60 s/120 s
  4. SMART KEY SYSTEM (for Entry Function) 

    Smart Key/Access (Certification ECU (Smart Key ECU assembly)) 

    SMART KEY/ACCESS REFERENCE

    Display (Item) Default Content Setting
    Park Wait Time 2.5 s Function to set waiting time to permit opening door after door is locked with entry lock function. 0.5 s / 1.5 s / 2.5 s / 5.0 s
    Ignition Available Area ALL Function to choose the available area for key to start the engine and cancel the steering lock. FRONT / ALL
    Trunk Open Mode ON Function to open the luggage compartment door when the driver has the key and presses the luggage open button. ON/OFF
    Key Low Battery Warning ON Function to set a warning function for a low battery. ON/OFF
  5. ENTRY UNLOCK MODE SWITCHING FUNCTION 
    1. To change the vehicle to entry unlock mode switching function, make sure that the vehicle power is off and simultaneously press and hold the electrical key's LOCK switch and another electrical key switch for 5 seconds.

      Driver door unlock default setting:

      When the switches are pressed and held for 5 seconds, the entry door unlock mode changes in the following order: driver door mode, all door mode.

      NOTE: After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.
      • Driver door unlock mode:

        When the driver door's touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

      • All door unlock mode:

        When the touch sensor is touched, all doors unlock.

    2. The certification ECU (smart key ECU assembly) receives this signal from the entry door control receiver and changes the smart key system to the entry unlock mode.
    3. The certification ECU (smart key ECU assembly) sounds the wireless door lock buzzer and combination meter buzzer to inform the user that the mode has been switched.
      WIRELESS DOOR LOCK BUZZER REFERENCE

      Mode Wireless Door Lock Buzzer Combination Meter Buzzer
      Driver Door (Default) Sounds 3 times Sounds once
      All Doors (Customized) Sounds 2 times Sounds once

      HINT:

      The function only changes the entry unlock mode of the smart key system. It does not switch the unlocking of the wireless door lock control.

  6. ELECTRICAL KEY CANCEL 

    The electrical key cancel operation disables the following functions:

    • Entry Unlock / Lock
    • Entry Luggage Compartment Open
    • Key Lock-in Prevention
    • Warning
    1. The operation procedures are as follows:

      Precondition:

      Engine switch off, driver side door closed and unlocked.

      1. Unlock the driver side door once with the UNLOCK switch of the key.
      2. Open the driver door within 5 seconds.
      3. Unlock the driver side door twice with the UNLOCK switch of the key within 5 seconds.
      4. Close and open the driver door twice within 30 seconds.

        (Driver door: Close → Open → Close → Open)

      5. Unlock the driver side door twice with the UNLOCK switch of the key within 5 seconds.
      6. Close and open the driver door within 30 seconds.

        (Driver door: Close → Open)

      7. Close the driver door within 5 seconds. When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.

  7. SMART KEY SYSTEM (for Start Function) 

    Smart Key / Access 

    SMART KEY/ACCESS REFERENCE

    Display (Item) Default Content Setting
    Ignition Available Area (Entry ignition available area) All Function to choose the available area for electrical key to start E/G and cancel the steering lock. Front/All
  8. LIGHTING SYSTEM 

    Illuminated Entry 

    ILLUMINATED ENTRY REFERENCE

    Display Default Content Setting
    Lighting Time 15s Changes the lighting time of the personal light(1), room light and engine switch illumination(2) after closing all of the doors. (It will quickly fade out in case of turning the ignition switch to ON) 7.5 s/15 s/30 s
    I/L when ACC OFF ON Lights up the personal light(1), room light and engine switch illumination(3) when the ignition switch is turned from ACC or ON to off. ON/OFF
    I/L ON W/Door Key Unlock(3) ON Lights up the personal light(1), room light and engine switch illumination when the doors are unlocked using mechanical key or door control transmitter. ON/OFF
    (1) w/ Sliding Roof
    (2) w/ Smart Key System
    (3) w/ Power Door Lock Control System
  9. METER/GAUGE SYSTEM 

    Combination Meter 

    COMBINATION METER REFERENCE

    Tester Display Default Content Setting
    Driver Side Seatbelt Warning Buzzer(1) On Function to change the setting of the seat belt warning buzzer. On, Off
    Front Passenger Side Seatbelt Warning Buzzer(1) On Function to change the setting of the seat belt warning buzzer. On, Off
    (1) This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more.
  10. AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) 

    Air Conditioner 

    AIR CONDITIONER REFERENCE

    Tester Display Default Content Setting
    Set Temperature Shift NORMAL Function to shift the temperature against the displayed temperature +2 C / +1 C / NORMAL / -1 C / -2 C
    Air Inlet Mode AUTO When turning the A/C ON to make the cabin cool down quickly, this is the function to change the mode automatically to RECIRCULATION mode MANUAL/AUTO
    Compressor Mode AUTO Function to turn the A/C ON automatically by pressing the AUTO button when the blower is ON and the A/C is OFF MANUAL/AUTO
    Compressor/Air Inlet DEF operation LINK Function to turn the A/C ON automatically linked with the FRONT DEF button when the A/C is OFF NORMAL / LINK
    Evaporator Control AUTO Function to set the evaporator control to the coldest position MANUAL/AUTO
    Foot/DEF Auto Mode ON Function to turn the airflow from FOOT / DEF ON automatically when AUTO MODE is ON OFF/ON
    Foot/DEF Automatic Blow Up Function ON Function to change the blower level automatically when the defroster is ON OFF/ON
scientia non olet · About LEMON Manuals