LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2009 >> Matrix Base, Standard >> Repair and Diagnosis >> Steering >> Power Steering >> Power Assist Steering Systems >> Power Steering System >> Freeze Frame Data
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Freeze Frame Data

  1. FREEZE FRAME DATA 
    NOTE:
    • It is difficult to show specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
    • Turn the ignition switch to ON and park the vehicle on level ground. Check the freeze frame data by using the Techstream.
    1. Turn the ignition switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON.
    4. Enter the following menus: Chassis / EMPS / Trouble Codes. Check the freeze frame data by following the prompts on the Techstream.

      EMPS 

      FREEZE FRAME DATA

      Tester Display Item Description: Range (Display) Inspection Condition Reference Value
      Meter Vehicle Velocity Vehicle speed from meter/
      Min.: 0 km/h (0 mph)
      Max.: 300 km/h (186.4 mph)      		 Vehicle is stopped 0 km/h (0 mph)
      Vehicle is driven at a constant speed No significant fluctuation
      Engine Revolution Engine revolution/
      Min.: 0 rpm
      Max.: 12800 rpm      		 Engine is running at a constant speed No significant fluctuation
      Motor Actual Current Amount of current to motor/
      Min.:-327.68 A
      Max.: 327.67 A      		 Power steering is operating Value changes in proportion to steering effort
      Command Value Current Demanded amount of current to motor/
      Min.:-327.68 A
      Max.: 327.67 A      		 Power steering is operating Value changes in proportion to steering effort
      Steering Angle Velocity Steering angle speed/
      Min.: -327.68 deg/s
      Max.: 327.67 deg/s      		 Steering wheel is turned Value changes in proportion to steering effort
      Thermistor Temperature ECU substrate temperature/
      Min.: -40°C (-40°F)
      Max.: 150°C (302°F)      		 Ignition switch ON -
      PIG Power Supply Power source voltage to activate motor/
      Min.: 0 V
      Max.: 20.1531 V      		 Power steering is operating 9 to 16 V
      IG Power Supply ECU power source voltage/
      Min.: 0 V
      Max.: 20.1531 V      		 Ignition switch ON 9 to 16 V
      Motor Rotation Angle Motor rotation angle/
      Min.: 0 deg
      Max.: 1441.77 deg      		 Power steering is operating During steering operation, motor rotation angle value changes from 0 to 360°
      Command Val Current 2 Demanded amount of current to motor/
      Min.:-327.68 A
      Max.: 327.67 A      		 Power steering is operating Value changes in proportion to steering effort
      PIG2 Voltage Voltage after boosting by coil/
      Min.: 0 V
      Max.: 45.955 V      		 Ignition switch ON
      Steering wheel is not turned      		 Approximately 27 V
      Ignition switch ON
      Steering wheel is turned      		 Value changes within 4 to 35 V range
      Motor Voltage Motor power supply voltage/
      Min.: 0V
      Max.: 45.955 V      		 Ignition switch ON
      Steering wheel is not turned      		 Approximately 27 V
      Ignition switch ON
      Steering wheel is turned      		 Value changes within 4 to 35 V range
      Motor Terminal Volt (U) Motor terminal voltage (U phase)/
      Min.: 0 V
      Max.: 46.667 V      		 Steering wheel is turned Value changes within 4 to 35 V range
      Motor Terminal Volt (V) Motor terminal voltage (V phase)/
      Min.: 0 V
      Max.: 46.667 V      		 Steering wheel is turned Value changes within 4 to 35 V range
      Motor Terminal Volt (W) Motor terminal voltage (W phase)/
      Min.: 0 V
      Max.: 46.667 V      		 Steering wheel is turned Value changes within 4 to 35 V range
      Torque Sensor 1 Output Torque sensor voltage/
      Min.: 0V
      Max.: 5 V      		 Ignition switch ON
      Steering wheel is not turned (without load)      		 2.3 to 2.7 V
      Ignition switch ON
      Steering wheel is turned to right with vehicle stopped      		 2.5 to 3.8 V
      Ignition switch ON
      Steering wheel is turned to left with vehicle stopped      		 1.2 to 2.5 V
      Torque Sensor 2 Output Torque sensor voltage/
      Min.: 0V
      Max.: 5 V      		 Ignition switch ON
      Steering wheel is not turned (without load)      		 2.3 to 2.7 V
      Ignition switch ON
      Steering wheel is turned to right with vehicle stopped      		 1.2 to 2.5 V
      Ignition switch ON
      Steering wheel is turned to left with vehicle stopped      		 2.5 to 3.8 V
      TRQ1 Zero Point Value Torque sensor voltage/
      Min.: 0V
      Max.: 5 V      		 Steering wheel is not turned -
      TRQ2 Zero Point Value Torque sensor voltage/
      Min.: 0 V
      Max.: 5 V      		 Steering wheel is not turned -
      PS Assist Signal Power steering assist signal/ ON or OFF No steering load (in neutral position) OFF
      Ignition switch ON
      Steering wheel is turned      		 ON
scientia non olet · About LEMON Manuals