Customize Parameters

HINT: 

The items in the table below can be customized.

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Customize Setting.
5. Select the setting by referring to the table below.
   SMART KEY / ACCESS
   
   

   Tester Display	Default	Content	Setting
   Park Wait Time	2.5 s	Function that sets waiting time to permit opening door after door is locked with entry lock function	0.5 s, 1.5 s, 2.5 s or 5 s
   Ignition Available Area	All	Function that switches the entry hybrid control system start detection area	Front or All*1
   Back Door Opening Operation*2	Long	Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch)	Long, Twice or OFF
   Door Unlock Mode*2, *3	Driver	Function that chooses the doors to be operated by entry unlock operation	All or Driver
   Touch Activation Over Threshold	Active	The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.	Active or Not Active

   HINT: 

   • *1: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected.
   • *2: w/ Entry Back Door Open Function
   • *3: except for Korea and Mexico
   WARNING
   
   

   Tester Display	Default	Content	Setting
   Key Low Battery Warning	ON	Function that warns driver that the key battery is weak	ON or OFF

HINT: 

The items in the table below can be customized.

1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (w/o Daytime Running Light))
   1. Turn the power switch on (IG).
   2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Setting.
   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Select Doors to Unlock	Driver's Door	Function that sets which doors are unlocked by the entry unlock function.	All Doors or Driver's Door	Certification ECU (smart key ECU assembly)
      Key System with Elec. Key*1 Entry and Start System*2	On	Function that enables or disables the smart key system.	On or Off	Certification ECU (smart key ECU assembly)

      • *1: except Korea
      • *2: for Korea
2. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (w/ Daytime Running Light))
   1. Turn the power switch on (IG).
   2. Enter the following menus: SETUP / Vehicle.
   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Key System with Elec. Key*1 Entry and Start System*2	On	Function that enables or disables the smart key system.	On or Off	Certification ECU (smart key ECU assembly)

      • *1: except Korea
      • *2: for Korea

1. Check that the power source mode is OFF and the LED on the key is not blinking. Press the LOCK switch and one of the other switches on the key at the same time for approximately 5 seconds while the key is in the detection area.

   Driver door unlock default setting:

   When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.

   NOTE:

   After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.

   • Driver door unlock mode:

     When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

   • All door unlock mode:

     When any touch sensor is touched, all doors unlock.

2. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver and changes the smart key system to entry unlock mode.
3. The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer.

   Mode	Wireless Door Lock Buzzer
   Driver Door (Default)	Sounds 3 times
   All Doors (Customized)	Sounds 2 times

   HINT: 

   The procedure only changes entry unlock mode of the smart key system. It does not switch the unlocking of the wireless door lock control.

The electrical key cancel operation disables the following functions:

• Entry Unlock/Lock
• Entry Hybrid Control System Start
• Entry System Back Door Open Function
• Key Lock-in Prevention
• Warning

1. The operation procedure is as follows:

   Precondition:

   Power switch off, driver door closed and unlocked.

   1. Push the unlock switch of the key once.
   2. Open the driver door within 5 seconds.
   3. Push the unlock switch of the key twice within 5 seconds.
   4. Close and open the driver door twice within 30 seconds.

      (Driver door: Close → Open → Close → Open)

   5. Push the unlock switch of the key twice within 5 seconds.
   6. Close and open the driver door within 30 seconds.

      (Driver door: Close → Open)

   7. Close the driver door within 5 seconds.

      When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

      To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.