LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2019 >> Prius LE AWD-e >> Repair and Diagnosis (Single Page) >> Restraints >> Air Bag, SRS >> Supplemental Restraint System - Diagnostic Codes (5 Of 5) & Symptom Tests >> Airbag System >> DTC B1900: Short in P/T Squib (RH) Circuit; DTC B1901: Open in P/T Squib (RH) Circuit; DTC B1902: Short in P/T Squib (RH) Circuit (to Ground); DTC B1903: Short in P/T Squib (RH) Circuit (to +B) [12/2018 - 08/2019] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC B1900: Short in P/T Squib (RH) Circuit; DTC B1901: Open in P/T Squib (RH) Circuit; DTC B1902: Short in P/T Squib (RH) Circuit (to Ground); DTC B1903: Short in P/T Squib (RH) Circuit (to +B) [12/2018 - 08/2019]: Procedure

  1. CHECK CONNECTORS 
    1. Turn the power switch off.
      GTY425806Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Outer Belt Assembly RH
      *2 Airbag ECU Assembly
      *3 Floor Wire
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the front seat outer belt assembly RH and airbag ECU assembly.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the front seat outer belt assembly RH and airbag ECU assembly.
    5. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

    6. Check that the floor wire connector (on the front seat outer belt assembly RH side) is not loose, deformed or damaged.

      OK

      The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.

    7. Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

      OK

      The short springs are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  2

  2. CHECK FRONT SEAT OUTER BELT ASSEMBLY RH 
    1. Connect the connector to the airbag ECU assembly.
      GTY585849Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Outer Belt Assembly RH
      *2 Airbag ECU Assembly
      *a Front view of wire harness connector
      (to Front Seat Outer Belt Assembly RH)
    2. Connect SST (resistance 2.1 Ω) to connector C.
      WARNING:

      Never connect a tester to the front seat outer belt assembly RH for measurement, as this may lead to a serious injury due to pretensioner deployment.

      NOTE:
      • Do not forcibly insert SST into the terminals of the connector when connecting it.
      • Insert SST straight into the terminals of the connector.
      • SST: 09843-18061 
    3. Connect the cable to the negative (-) auxiliary battery terminal.
    4. Clear the DTCs stored in memory.

      Refer to DTC CHECK / CLEAR [12/2018 - 08/2019]

      Body Electrical > SRS Airbag > Clear DTCs 

    5. Turn the power switch off.
    6. Turn the power switch on (IG), and wait for at least 60 seconds.
    7. Check for DTCs.

      Refer to DTC CHECK / CLEAR [12/2018 - 08/2019]

      Body Electrical > SRS Airbag > Trouble Codes 

      OK

      DTC B1900, B1901, B1902 or B1903 is not output.

      HINT: 

      Codes other than DTCs B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.

    8. Turn the power switch off.
    9. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Disconnect SST from connector C.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH. Refer to  REMOVAL [12/2018 - 07/2020] 

    Result: 

    NG 

    See step  3

  3. CHECK FLOOR WIRE 
    1. Disconnect the floor wire from the airbag ECU assembly.
      GTY605989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Outer Belt Assembly RH
      *2 Airbag ECU Assembly
      *3 Floor Wire
      *a Front view of wire harness connector
      (to Front Seat Outer Belt Assembly RH)
    2. Check for a short to B+ in the circuit.
      1. Connect the cable to the negative (-) auxiliary battery terminal.
      2. Turn the power switch on (IG).
      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        (M49)

        (M49)

        Tester Connection Condition Specified Condition
        M49-1 (R+) - Body ground Power switch on (IG) Below 1 V
        M49-2 (R-) - Body ground Power switch on (IG) Below 1 V
      4. Turn the power switch off.
      5. Disconnect the cable from the negative (-) auxiliary battery terminal.
        WARNING:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check for an open in the circuit.
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        (M49)

        (M49)

        Tester Connection Condition Specified Condition
        M49-1 (R+) - M49-2 (R-) Always Below 1 Ω
    4. Check for a short to ground in the circuit.
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        (M49)

        (M49)

        Tester Connection Condition Specified Condition
        M49-1 (R+) - Body ground Always 1 MΩ or higher
        M49-2 (R-) - Body ground Always 1 MΩ or higher
    5. Check for a short in the circuit.
      1. Release the activation prevention mechanism built into connector B.

        Refer to DIAGNOSIS SYSTEM [08/2016 - 08/2019]

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        (M49)

        (M49)

        Tester Connection Condition Specified Condition
        M49-1 (R+) - M49-2 (R-) Always 1 MΩ or higher
      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  4

  4. CHECK DTC 
    1. Connect the connectors to the front seat outer belt assembly RH and airbag ECU assembly.
      GTY440123Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Outer Belt Assembly RH
      *2 Airbag ECU Assembly
    2. Connect the cable to the negative (-) auxiliary battery terminal.
    3. Clear the DTCs stored in memory.

      Refer to DTC CHECK / CLEAR [12/2018 - 08/2019]

      Body Electrical > SRS Airbag > Clear DTCs 

    4. Turn the power switch off.
    5. Turn the power switch on (IG), and wait for at least 60 seconds.
    6. Check for DTCs.

      Refer to DTC CHECK / CLEAR [12/2018 - 08/2019]

      Body Electrical > SRS Airbag > Trouble Codes 

      OK

      DTC B1900, B1901, B1902 or B1903 is not output.

      HINT: 

      Codes other than DTCs B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2018 - 07/2020] 

    Result: 

    NG 

    REPLACE AIRBAG ECU ASSEMBLY. Refer to  REMOVAL [12/2018 - 08/2019] 

scientia non olet · About LEMON Manuals