DTC P062F-46: Internal Control Module EEPROM Calibration / Parameter Memory Failure [11/2018 - 10/2023]: Procedure

PERFORM REGISTRATION (ECU EXCHANGE)

Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.

Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.

Powertrain > Stop and Start > Utility

Tester Display
ECU Exchange

According to the display on the Techstream, select "Step 1 Save" and then "Next" to download the ECU data from the engine stop and start ECU.

Refer to REGISTRATION [11/2018 - 10/2019] , or refer to REGISTRATION [10/2019 - 12/2021] , or refer to REGISTRATION [12/2021 - 10/2022] , or refer to REGISTRATION [10/2022 - 10/2023]

Result

Proceed to
NEXT

Result:

See step 2

CLEAR DTC

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs

Result

Proceed to
NEXT

Result:

See step 3

PERFORM REGISTRATION (STARTER EXCHANGE, RESET A/C INFORMATION, DECELERATION SENSOR ZERO POINT CLEAR)

Clear the number of starter operations.

Enter the following menus: Powertrain / Stop and Start / Utility / Starter Exchange.

Powertrain > Stop and Start > Utility

Tester Display
Starter Exchange

Clear the air conditioning information.

Enter the following menus: Powertrain / Stop and Start / Utility / Reset A/C Information.

Powertrain > Stop and Start > Utility

Tester Display
Reset A/C Information

Clear the zero point calibration data of the deceleration sensor.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.

Powertrain > Stop and Start > Utility

Tester Display
Deceleration Sensor Zero Point Clear

Result

Proceed to
NEXT

Result:

See step 4

PERFORM REGISTRATION (ECU EXCHANGE, DECELERATION SENSOR ZERO POINT CALIBRATION)

Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.

Powertrain > Stop and Start > Utility

Tester Display
ECU Exchange

According to the display on the Techstream, select "Step 3 Write" and then "Next" to write the ECU data to the new engine stop and start ECU.
Refer to REGISTRATION [11/2018 - 10/2019] , or refer to REGISTRATION [10/2019 - 12/2021] , or refer to REGISTRATION [12/2021 - 10/2022] , or refer to REGISTRATION [10/2022 - 10/2023]
Perform air conditioning information learning.
Refer to REGISTRATION [11/2018 - 10/2019] , or refer to REGISTRATION [10/2019 - 12/2021] , or refer to REGISTRATION [12/2021 - 10/2022] , or refer to REGISTRATION [10/2022 - 10/2023]

HINT:

When initialization of the air conditioning information is complete, air conditioning information learning is automatically performed.

Perform deceleration sensor zero point calibration.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.

Powertrain > Stop and Start > Utility

Tester Display
Deceleration Sensor Zero Point Calibration

Result

Proceed to
NEXT

Result:

See step 5

CHECK DTC OUTPUT

Start the engine and warm it up.
Turn the air conditioning system off.
Drive the vehicle at 7 km/h (4 mph) or more.
WARNING:
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Depress the brake pedal and stop the vehicle.
Allow the engine to stop by stop and start control. (Keep the shift lever in D.)
Release the brake pedal with the shift lever in D to start the engine.

Check for DTCs.

Powertrain > Stop and Start > Trouble Codes

Result

Result	Proceed to
DTCs are not output	A
DTC P062F-46 is output	B

Result:

END

Result:

REPLACE ENGINE STOP AND START ECU. Refer to REMOVAL [11/2018 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023]