Diagnostic Mode 06 - Read Test Results For Specific Diagnostic Functions
Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.
The min & max values for each individual test in Mode 06 represent the min & max operating values for a properly operating system. This data is provided to the individual aftermarket scan tool companies for development of their scan tool. Depending on the scan tool being used, the min & max values shown may vary, or be rounded up or down to the nearest decimal point depending on the aftermarket scan tool company's development process. e.g.:
| Minimum Value | |
|---|---|
| GST manual documentation | 0.3499 |
| Aftermarket scan tool display | 0.35 |
Depending on the scan tool and protocol used, the information displayed in Diagnostic Mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), On-Board Diagnostic Monitor Identifier (OBDMID), or contain no name at all and may be referenced by only a number.
Test requirements
- Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.
- No DTCs stored in the DTC memory.
- Coolant temperature at least 80° C.
Work procedure
-- Connect the scan tool.
-- Start the engine and let run at idle speed.
-- Select Mode 6: Check test the results of components that are not continuously monitored.
Select the desired Test-ID.
The current minimum and maximum values will be displayed on the scan tool screen.
The following table is a numerical list of all "Test-IDs" that may be selected.
Monitor-ID $01: Oxygen Sensor Monitor Bank 1 - Sensor 1
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID $01".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $C1 | P0133 | HO2 Sensor Bank 1, Sensor 1 Dynamic Check Part 1 | 0.0 s | 6553.5 s | Refer to DTC P0133 Engine Control Module -- => P0133 in the DTC summary table. |
| $C2 | P0133 | HO2 Sensor Bank 1, Sensor 1 Dynamic Check - Part 2. | 0.0 s | 6553.5 s | Refer to DTC P0133 Engine Control Module -- => P0133 in the DTC summary table. |
| $C4 | P2195, P2196 | HO2 Sensor Bank 1, Sensor 1 Plausibility Check - Part Load. | 0.00% | 100.01% | Refer to DTC P2195 Engine Control Module -- => P2195 OR P2196 Engine Control Module -- => P2196 in the DTC summary table. |
| $C5 | P2195, P2196 | HO2 Sensor Bank 1, Sensor 1 Plausibility Check - Over run. | 0.00% | 100.01% | Refer to DTC P2195 Engine Control Module -- => P2195 OR P2196 Engine Control Module -- => P2196 in the DTC summary table. |
| $C6 | P014D | HO2 Sensor Bank 1, Sensor 1 Dynamic Check with Bank 1, Sensor 2 | 0.0 s | 6553.5 s | Refer to DTC P014D Engine Control Module -- => P014D in the DTC summary table. |
| $C7 | P0133 | HO2 Sensor Bank 1, Sensor 1 Dynamic Check - Part 2. | 0.0 s | 6553.5 s | Refer to DTC P0133 Engine Control Module -- => P0133 in the DTC summary table. |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
Monitor-ID $02: Oxygen Sensor Monitor Bank 1- Sensor 2
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID $02".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $C1 | P0139 | HO2 Sensor Bank 1, Sensor 2 Dynamic Check Part 1 | 0.0 s | 6553.5 s | Refer to DTC P0139 Engine Control Module -- => P0139 in the DTC summary table. |
| $C2 | P0139 | HO2 Sensor Bank 1, Sensor 2 Dynamic Check - Part 2. | 0.0 s | 6553.5 s | Refer to DTC P0139 Engine Control Module -- => P0139 in the DTC summary table. |
| $C4 | P2270 P2271 | HO2 Sensor Bank 1, Sensor 2 Plausibility Check - Part Load. | 0.00% | 100.01% | Refer to DTC P2270 Engine Control Module -- => P2270 OR P2271 Engine Control Module -- => P2271 in the DTC summary table. |
| $C5 | P2270 P2271 | HO2 Sensor Bank 1, Sensor 2 Plausibility Check - Over run. | 0.00% | 100.01% | Refer to DTC P2270 Engine Control Module -- => P2270 OR P2271 Engine Control Module -- => P2271 in the DTC summary table. |
| $C6 | P013B | HO2 Sensor Bank 1, Sensor 2 Dynamic Check with Bank 1, Sensor 1 | 0.0 s | 6553.5 s | Refer to DTC P013B Engine Control Module -- => P013B in the DTC summary table. |
| $C7 | P0139 | HO2 Sensor Bank 1, Sensor 2 Dynamic Check - Part 2. | 0.0 s | 6553.5 s | Refer to DTC P0139 Engine Control Module -- => P0139 in the DTC summary table. |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
Monitor-ID $21: Catalytic Converter Monitoring
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 21".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $C0 | P0420 | Catalytic converter monitoring. | 0.00 | 19.99 | Refer to DTC P0420 Engine Control Module -- => P0420 in the DTC summary table. |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
Monitor-ID $31: EGR Control Loop
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 31".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $C0 | P0401 P0402 | EGR Control Loop. | -3276.8 mg/stroke | 3276.7 mg/stroke | Refer to DTC P0401 Engine Control Module -- => P0401 . Refer to DTC P0402 Engine Control Module -- => P0402 in the DTC summary table. |
| $C2 | P0402 | EGR High Flow | 0 | 19.99 | Refer to DTC P0402 Engine Control Module -- => P0402 in the DTC summary table. |
| $CA | P2457 | Low-pressure EGR Cooler. Cooler Performance Check | - 3276.7° C | 3276.7° C | Refer to DTC P2457 Engine Control Module -- => P2457 in the DTC summary table. |
| $D0: | P240F | EGR Slow Response Positive | -3276.8 mg/stroke | 3276.7 mg/stroke | Refer to DTC P240F Engine Control Module -- => P240F in the DTC summary table. |
| $D1: | P240F | EGR Slow Response Negative | -3276.8 mg/stroke | 3276.7 mg/stroke | Refer to DTC P240F Engine Control Module -- => P240F in the DTC summary table. |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
Monitor-ID $81: Zero Fuel Calibration Monitor
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 81".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $C1 | P0263 | Zero Fuel Calibration Monitor Cylinder 1 | 0 μs | 6553.5 μs | Refer to DTC P0263 Engine Control Module -- => P0263 in the DTC summary table. |
| $C2 | P0266 | Zero Fuel Calibration Monitor Cylinder 2 | 0 μs | 6553.5 μs | Refer to DTC P0266 Engine Control Module -- => P0266 in the DTC summary table. |
| $C3 | P0269 | Zero Fuel Calibration Monitor Cylinder 3 | 0 μs | 6553.5 μs | Refer to DTC P0269 Engine Control Module -- => P0269 in the DTC summary table. |
| $C4 | P0272 | Zero Fuel Calibration Monitor Cylinder 4 | 0 μs | 6553.5 μs | Refer to DTC P0272 Engine Control Module -- => P0272 in the DTC summary table. |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
-- Switch the ignition off.
Monitor-ID $85: Boost Pressure Control Loop
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 85".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $C3 | P00AF | Charge Air Boost Pressure Control Loop | 0.00% | 100.01% | Refer to DTC P00AF Engine Control Module -- => P00AF in the DTC summary table. |
| $CA | P026A | Charge Air Cooler Under-cooling | 0.00 | 19.99 | Refer to DTC P026A Engine Control Module -- => P026A in the DTC summary table. |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
-- Switch the ignition off.
Monitor-ID $90: NOx Absorber
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 3B".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $C0 | P2000 | NOx absorber missing substrate. | 0.00 g | 65.535 g | Refer to DTC P2000 Engine Control Module -- => P2000 in the DTC summary table. |
| $C6 | P2000 | NOx absorber storage capacity. | 0.00 g | 65.535 g | Refer to DTC P2000 Engine Control Module -- => P2000 in the DTC summary table. |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
Monitor-ID $A2: Mis-Fire Cylinder 1 Data
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A2".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| $0B | P0301 | Misfire cylinder 1, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0301 Engine Control Module -- => P0301 . in the DTC summary table. | |
| $0C | P0301 | Misfire cylinder 1, in this Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0301. Engine Control Module -- => P0301 in the DTC summary table. | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
Monitor-ID $A3: Mis-Fire Cylinder 2 Data
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6 Check test the results of components that are not continuously monitored".
Select "Monitor-ID A3:".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| $0B | P0302 | Misfire cylinder 2, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0302 in the DTC summary table. Engine Control Module -- => P0302 . | |
| $0C | P0302 | Misfire cylinder 2, in this Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0302 in the DTC summary table. Engine Control Module -- => P0302 . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
Monitor-ID $A4: Mis-Fire Cylinder 3 Data
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A4".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| $0B | P0303 | Misfire cylinder 3, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0303 in the DTC summary table. Engine Control Module -- => P0303 . | |
| $0C | P0303 | Misfire cylinder 3, in this Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0303 in the DTC summary table. Engine Control Module -- => P0303 . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
Monitor-ID $A5: Mis-Fire Cylinder 4 Data
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A5".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| $0B | P0304 | Misfire cylinder 4, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0304 in the DTC summary table. Engine Control Module -- => P0304 . | |
| $0C | P0304 | Misfire cylinder 4, in this Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0304 in the DTC summary table. Engine Control Module -- => P0304 . | |
-- Switch the ignition off.
-- If any of the components or systems fail to meet the specified values, refer to Diagnostic Mode 03: Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
-- Switch the ignition off.
Monitor-ID $B2: Particulate Matter Trap Efficiency
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID B2".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $C4 | P2458 | No Complete PM Regeneration | 0 s | 65535 s | Refer to DTC P2458 Engine Control Module -- => P2458 in the DTC summary table. |
| $C5 | P2459 | Frequency PM Regeneration | 0.00 g | 655.35 g | Refer to DTC P2459 Engine Control Module -- => P2459 in the DTC summary table. |
| $D1 | P2002 | Particulate Matter Trap Missing over delta pressure | 0.00 kPa | 655.35 kPa | Refer to DTC P2002 Engine Control Module -- => P2002 in the DTC summary table. |
| $D2 | Particulate matter trap missing over temperature gradient | ||||
| $D5 | P2002 | Particulate Matter Trap Efficiency over delta pressure EGR-LP filter | -32.768 mg/stroke | 32.767 mg/stroke | Refer to DTC P2002 Engine Control Module -- => P2002 in the DTC summary table. |
-- Switch the ignition off.
-- If any of the components or systems fail to meet the specified values, refer to Diagnostic Mode 03: Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
-- Switch the ignition off.