LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Volkswagen >> 2014 >> Passat TDI SE, Standard Trans >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> 3.6L - Generic Scan Tool - Engine Code: CDVB (Transmission DTC Tables & Diagnostic Procedures) >> St Generic Scan Tool >> Diagnosis And Testing >> Diagnostic Procedures >> Accelerator Pedal Module -GX2-, CHECKING >> Test Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test Procedure

Step Procedure Result / Action to Take
1
  • PERFORM: Preliminary Check to verify the customers complaint. Refer to PRELIMINARY CHECK .
-- Was Complaint verified?		 -- YES:
  • GO TO Step 2.
-- NO:
  • GATHER more information from customer about the complaint.
2
  • CONNECT: Scan Tool.
  • IGNITION: ON.
  • CHECK: Throttle valve position closed:
  • SPECIFIED VALUE: 3 - 25%.
  • DEPRESS: Accelerator pedal slowly to WOT while observing the percentage display. The percentage display must increase uniformly.
  • CHECK: Throttle valve position at WOT:
  • SPECIFIED VALUE: 84 - 97%.
  • IGNITION: OFF.
-- Was Value obtained?		 -- YES:
  • GO TO Step 3.
-- NO:
  • GO TO Step 4.
3
  • Condition may be intermittent.
  • PERFORM: Visual Inspection of wiring and component.
  • CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
  • REPAIR: Faulty wiring or connector.
  • GO TO: Step 6.
4
  • DISCONNECT: Accelerator Pedal Module -GX2- harness connector.
  • IGNITION: ON.
  • CHECK: Accelerator Pedal Module -GX2- harness connector terminals 1 to 5 and 2 to 3 for voltage.
  • SPECIFIED VALUE: About 5.0 V.
  • IGNITION: OFF.
-- Were Values obtained?		 -- YES:
  • GO TO Step 5.
-- NO:
  • GO TO Step 6.
5
  • REMOVE: Engine Control Module - J623-. Refer to appropriate repair information.
  • CHECK: Accelerator Pedal Module -GX2- harness connector terminal 6 to the Engine Control Module - J623- harness connector T94/ 57 for resistance.
  • CHECK: Accelerator Pedal Module -GX2- harness connector terminal 4 to the Engine Control Module - J623- harness connector T94/ 79 for resistance.
  • SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω).
-- Were Values obtained?		 -- YES:
  • REPLACE: Accelerator Pedal Module -GX2-. Refer to appropriate repair information.
  • GO TO: Step 7.
-- NO:
  • CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
  • REPAIR: Faulty wiring or connector.
  • GO TO: Step 7.
6
  • REMOVE: Engine Control Module - J623-. Refer to appropriate repair information.
  • CHECK: Accelerator Pedal Module -GX2- harness connector terminal 5 to the Engine Control Module - J623- harness connector T94 / 56 for resistance.
  • CHECK: Accelerator Pedal Module -GX2- harness connector terminal 1 to the Engine Control Module - J623- harness connector T94 / 58 for resistance.
  • CHECK: Accelerator Pedal Module -GX2- harness connector terminal 3 to the Engine Control Module - J623- harness connector T94 / 78 for resistance.
  • CHECK: Accelerator Pedal Module -GX2- harness connector terminal 2 to the Engine Control Module - J623- harness connector T94 / 80 for resistance.
  • SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω).
-- Were Values obtained?		 -- YES:
  • REPLACE Engine Control Module -J623-. Refer to appropriate repair information.
  • GO TO: Step 7.
-- NO:
  • CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
  • REPAIR: Faulty wiring or connector.
  • GO TO: Step 7.
7
  • Final Procedure
  • Perform a road test to verify repair.
  • Do any DTC's return:
 -- YES: -- NO:
  • Repair is complete. Generate readiness code. Refer to READINESS CODE .
  • Return vehicle to Customer.
scientia non olet · About LEMON Manuals