Diagnostic Mode 06 - Read Test Results For Specific Diagnostic Functions
Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.
The min & max values for each individual test in Mode 06 represent the minimum & maximum operating values for a properly operating system. This data is provided to the individual aftermarket scan tool companies for development of their scan tool. Depending on the scan tool being used, the min & max values shown may vary, or be rounded up or down to the nearest decimal point depending on the aftermarket scan tool company's development process. e.g.:
| Minimum Value | |
|---|---|
| GST manual documentation | 0.3499 |
| Aftermarket scan tool display | 0.35 |
Depending on the scan tool and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).
Test requirements
- Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.
- No DTCs stored in the DTC memory.
- Coolant temperature at least 80 °C.
Work procedure
-- Connect the scan tool.
-- Start the engine and let run at idle speed.
-- Select Mode 6: Check test the results of components that are not continuously monitored.
Select the desired Test-ID..
The current minimum and maximum values will be displayed on the scan tool screen.
The following table is a numerical list of all "Test-IDs" that may be selected.
Monitor-ID $01: Oxygen Sensor Monitor Bank 1 - Sensor 1
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID $01".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $83 | P0133 | Response Check. | 0.150 V to 0.300 V | 1.99 V | Refer to DTC P0133 in the DTC summary table.DTC TABLES . |
| $84 | P2195 / P2196 | Response Check. | -0.060 V | 0.060 V | Refer to DTC P2195 / P2196 in the DTC summary table.DTC TABLES |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $02: Oxygen Sensor Monitor Bank 1- Sensor 2
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID $02".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $05 | P0139 | Deceleration test - O2 transient time. | 0 Sec. | 1.2 Sec. | Refer to DTC P0139 in the DTC summary table. DTC TABLES . |
| $07 | - | Minimum oxygen sensor voltage value in test. | 0 V | .450 V | - |
| $08 | - | Maximum oxygen sensor voltage value in test. | .450 V | 1.260 V | - |
| $81 | P2271 | Output Voltage rich during decel. | 0 V | 0.7025 V | Refer to DTC P2271 in the DTC summary table. DTC TABLES |
| $82 | P2270 | Output Voltage lean during accel. | 0.6305 V | 1.0795 V | Refer to DTC P2270 in the DTC summary table. DTC TABLES |
| $86 | P2271 | Deceleration test response time. | 0 Sec. | 8 Sec. | Refer to DTC P2271 in the DTC summary table. DTC TABLES |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $21: Catalytic Converter Monitoring
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 21".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $84 | P0420 | Catalytic converter monitoring bank 1. | 0.999 | 19.988 | Refer to DTC P0420 in the DTC summary table. DTC TABLES . |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $35: Camshaft Adjustment / V V T Bank 1
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 21".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $80 | P0011 | V V T specified position not reached. | -32 Deg. | 28 Deg. | Refer to DTC P0011 in the DTC summary table. DTC TABLES |
| $81 | P000A | V V T specified position is reached too slow. | -32 Deg | 28 Deg. | Refer to DTC P000A in the DTC summary table. DTC TABLES |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $3A: Fuel Tank EVAP System Integrity/Leak Test (0.90/2.25 mm)
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 3A".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $81 | P0455 | Tank leak test: Large leak. | 0.950 Sec. | 65.535 Sec. | Refer to DTC P0455 in the DTC summary table. DTC TABLES . |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $3B: Fuel Tank EVAP System Integrity/Leak Test (0.40/1.0 mm)
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 3B".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $81 | P0455 | Fuel Tank Leak Test: Small leak. | 1.550 Sec. | 65.535 Sec. | Refer to DTC P0442 the DTC summary table. DTC TABLES |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $3C: Fuel Tank EVAP System Integrity/Leak Test (0.20/0.5 mm)
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 3C".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $81 | P0456 | Tank leak test: Pinhole leak (0.5 mm). | 4.50 Sec. | 65.535 Sec | Refer to DTC P0456 in the DTC summary table. DTC TABLES |
| $82 | --- | Fuel Tank Leak Test. | 12.00 g | 6553.50 g | --- |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $3D: EVAP Valve Function Check
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 3D".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $80 | P0441 | Purge Flow Monitor | .300 | 1.999 | Refer to DTC P0441 in the DTC summary table. DTC TABLES . |
| $82 | - | Purge Flow OK by deviation lambda control. | -9.994 OR 0.080 | -0.080 OR 9.994 | - |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $41: Oxygen Sensor Heater Monitor Bank 1 - Sensor 1
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 41".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $85 | P0135 | Oxygen sensor ceramic temperature, Bank 1 Sensor 1. | 714.9 °C | 1199.9 °C | Refer to DTC P0135 in the DTC summary table. DTC TABLES . |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $42: Oxygen Sensor Heater Monitor Bank 1 - Sensor 2
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 42".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| $81 | P0141 | Oxygen sensor internal resistance test, Bank 1 Sensor 2. | 0.0 kOhms | 4.560 kOhms | Refer to DTC P0141 in the DTC summary table. DTC TABLES . |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $A2: Mis-Fire Cylinder 1 Data
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A2".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| $0B | P0301 | Misfire cylinder 1, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0301 in the DTC summary table. DTC TABLES . | |
| $0C | P0301 | Misfire cylinder 1, current Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0301 in the DTC summary table. DTC TABLES . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $A3: Mis-Fire Cylinder 2 Data
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6 Check test the results of components that are not continuously monitored".
Select "Monitor-ID A3:".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| $0B | P0302 | Misfire cylinder 2, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0302 in the DTC summary table. DTC TABLES . | |
| $0C | P0302 | Misfire cylinder 2, current Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0302 in the DTC summary table. DTC TABLES . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $A4: Mis-Fire Cylinder 3 Data
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A4".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| $0B | P0303 | Misfire cylinder 3, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0303 in the DTC summary table. DTC TABLES . | |
| $0C | P0303 | Misfire cylinder 3, current Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0303 in the DTC summary table. DTC TABLES . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition OFF.
Monitor-ID $A5: Mis-Fire Cylinder 4 Data
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A5".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| $0B | P0304 | Misfire cylinder 4, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0304 in the DTC summary table. DTC TABLES . | |
| $0C | P0304 | Misfire cylinder 4, current Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0304 in the DTC summary table. DTC TABLES . | |
-- Switch the ignition OFF.
-- If any of the components or systems fail to meet the specified values, refer to Diagnostic Mode 03: Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
-- Switch the ignition OFF.