Abs Control Module -J104- And Abs Hydraulic Unit -N55-, Removing And Installing, RHD With Abs Mark 70 Abs/ASR: Removing

Installation location:

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Brake Booster with Tandem Brake Master Cylinder
ABS Hydraulic Unit -N55- with ABS Control Module -J104-

CAUTION:

Do not confuse the brake lines when connecting them to the tandem brake master cylinder and the ABS Hydraulic Unit -N55-. Mark the lines in their installed position before removing them.

The brake lines near the ABS Hydraulic Unit -N55- must not be bent.

-- Retrieve the present coding from the ABS Control Module -J104- and write it down.

Use the Vehicle Diagnostic Tester.

Chassis
Brake System
Anti-Lock Braking System ABS/ASR Mark 70
Function
Check ABS Control Module J104 coding

NOTE:

The battery ground cable must be disconnected for the following procedure. For this reason, check if a coded radio is installed. If necessary, obtain anti-theft code beforehand.

CAUTION:

Danger of causing damage to electronic components when disconnecting the battery.

Follow the steps for disconnecting the battery.

Vehicles With 2.0L Gasoline Engine And Turbocharger

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the engine cover upward from the mounting points -arrows-. Refer to ENGINE COVER (CNLA, CRJA) , ENGINE COVER (CVCA, CUUA, CUUB, DELA, DEBA, DEJA, DGMA) and ENGINE COVER (CPLA, CPPA, CPKA, CPRA) .

Vehicles with 1.4L gasoline engine, turbocharger and compressor:

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Lift the engine cover -3- upward at points -1- in the -direction of the arrow-.

-- Pull the cover out of the bracket -2- in the -direction of the arrow-.

Vehicles With Diesel Engine:

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove engine cover near the -arrows-.

-- Pay attention to the sequence given -1- to -4-. Refer to ENGINE COVER (CVCA, CUUA, CUUB, DELA, DEBA, DEJA, DGMA) .

-- Reach under the engine cover as far as possible.

Continuation For All Vehicles:

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- If necessary, remove the intake hose -2-. Refer to AIR FILTER (CNLA, CRJA) , AIR FILTER (CZCA, CZDA, CZTA) , AIR FILTER (CBPA, CKJA) and AIR FILTER (CPLA, CPPA, CPKA, CPRA) .

-- To do this, loosen clamps -1-.

-- Seal the openings with the Engine Bung Set :VAS 6122 .

-- Disconnect and remove the connector from the ABS Control Module -J104- in -direction of the arrow-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Push the fuse -2- downward in the -direction of the arrow-.

-- Unlock the locking mechanism -1- to disconnect the connector -3- from the ABS Control Module -J104-.

-- To do this, press the locking mechanism -1- downward in the -direction of the arrow-.

-- Insert the Brake Pedal Actuator :V.A.G 1869/2 .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove left front caps -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove left rear caps -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Use a suitable bleeder hose

It must fit tightly on the bleeder valve so that no air can get into the brake system

-- Attach the bleeder bottle bleed hose -1- to the left front brake caliper breather valve.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Open the breather valve.

-- Attach the bleeder bottle bleed hose -1- to the brake caliper breather valve/left rear brake cylinder.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Open the breather valve.

-- Push the brake pedal at least 60 mm using the Brake Pedal Actuator :V.A.G 1869/2 .

-- Close the left front and left rear bleeder valves.

Do not remove the Brake Pedal Actuator :V.A.G 1869/2 .

Vehicles With Manual Transmission:

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Unclip the hydraulic line -1- on the bracket -2- -arrows-.

Continuation For All Vehicles:

-- Place enough lint-free cloths under the ABS Control Module -J104- and the ABS Hydraulic Unit -N55-.

Make sure no brake fluid gets on the contacts

-- Mark the brake lines -A- and -B- from the brake master cylinder.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the brake lines -A- and -B- from the ABS Hydraulic Unit -N55-.

-- Seal the threaded hole immediately with plugs from the assembly repair kit.

-- Close brake lines immediately using Sealing Plugs or with suitable plugs from the Engine Bung Set :VAS 6122 .

-- Mark the brake lines -1- to -4-, unscrew and the seal.

-- Seal the threaded hole immediately with plugs from the assembly repair kit.

-- Close brake lines immediately using Sealing Plugs or with suitable plugs from the Engine Bung Set :VAS 6122 .

-- Remove the ABS Hydraulic Unit -N55- and the ABS Control Module -J104- in -direction of arrow- and pull upward out of the shock absorbers.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the ABS Hydraulic Unit -N55- with the ABS Control Module -J104-.