Test Procedure

Step	Procedure	Result / Action to Take
1	PERFORM: Preliminary Check to verify the customers complaint. Refer to: PERFORM: Preliminary Check to verify the customers complaint. Refer to PRELIMINARY CHECK . -- Was Complaint verified?	-- YES: GO TO Step 2. -- NO: GATHER more information from customer about the complaint.
2	IGNITION: OFF. DISCONNECT: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector. CHECK: Oxygen Sensor 1 After Catalytic Converter -GX7- component connector terminals 1 to 2 for resistance. SPECIFIED VALUE: 2 - 4 Ω (+/- 0.5 Ω @ 25° C). -- Was Value obtained?	-- YES: GO TO Step 3. -- NO: REPLACE: Oxygen Sensor 1 After Catalytic Converter -GX7-. GO TO Step 6.
3	IGNITION: ON. CHECK: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector terminal 1 to ground for voltage. IGNITION: OFF. SPECIFIED VALUE: Battery voltage. -- Was Value obtained?	-- YES: GO TO Step 4. -- NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO Step 6.
4	RECONNECT: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector. CONNECT: Scan Tool. START: Engine and let Idle. Perform the function test located in diagnostic mode 06. Refer to appropriate Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions, DIAGNOSTIC MODES 01 - 0A . IGNITION: OFF. SPECIFIED VALUE: Mode 6 Pass. -- Were Values obtained?	-- YES: FAULT: Is intermittent. PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO Step 6. -- NO: GO TO Step 5.
5	DISCONNECT: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector. REMOVE: Engine/Motor Control Module -J623-. CHECK: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector terminal 2 to the Engine/Motor Control Module -J623- harness connector T91 / 74 for resistance. CHECK: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector terminal 3 to the Engine/Motor Control Module -J623- harness connector T91 / 29 for resistance. CHECK: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector terminal 4 to the Engine/Motor Control Module -J623- harness connector T91 / 28 for resistance. SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). -- Were Values obtained?	-- YES: REPLACE: Oxygen Sensor 1 After Catalytic Converter -GX7-. GO TO Step 6. -- NO : PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO Step 6.
6	Final Procedure Perform a road test to verify repair. -- Does the original DTC return?	-- YES: CHECK: Engine/Motor Control Module -J623- harness connector for any damaged, pushed out pins. REPAIR: As necessary. If all electrical connections are OK: REPLACE: Engine/Motor Control Module -J623-. Clear the DTC's. Refer to: DIAGNOSTIC MODE 04 - ERASE DTC MEMORY . Repair is complete. Generate Readiness Code. Refer to: READINESS CODE . Return vehicle to Customer. -- NO : Perform the diagnostic procedure for any DTC's. If no DTC's return, the repair is complete. Return vehicle to customer.