Engine - Cooling, Ignition & Control Systems - Specifications, Removal & Installation (Convertible)

• Engine
  • Misfire diagnostic
  • Outer temperature sensor Specifications
  • Outside temperature sensor Specifications
  • Replacing ignition coils
    • Removing ignition coils
    • Installing ignition coils
  • Replacing relays in the main fuse box and other relays in the engine compartment
    • Removing
    • Installing
  • Replacing EVAP canister shut-off valve
    • Removing fender liner
    • Removing EVAP canister shut-off valve
    • Installing EVAP canister shut-off valve
    • Installing fender liner
  • Replacing the canister purge (CP) valve
    • Replacing the canister purge (CP) valve
      • Removing the canister purge (CP) valve
      • Installing a new canister purge (CP) valve
  • Replacing the shut-off valve for the carbon filter container
    • Replacing the shut-off valve for the carbon filter container
      • Removing the shut-off valve
      • Installing the shut-off valve
  • Replacing the engine speed (RPM) sensor (B6xx4x -2001)
    • Removing the engine speed (RPM) sensor
    • Installing the engine speed (RPM) sensor
  • Replacing the immobilizer control module
    • General
    • Identification
    • Removal
    • Installation
  • Replacing the mass air flow (MAF) sensor
    • Removing the mass air flow (MAF) sensor
    • Installing the mass air flow (MAF) sensor
  • Replacing the variable valve timing solenoid
    • Notes
    • Preparations
      • Notes
      • Removing the variable valve timing solenoid
      • Installing the variable valve timing solenoid
      • Finishing
  • Screwed joint, torque/angle joint
  • Signal description
  • Signal description Motronic 4.4
  • Signal specification (C70)
  • Signal specification (S80 & XC90)
  • Signal specification (XC90 - 6 cylinder engines -2004)
• Cooling
  • Replacing engine coolant temperature (ECT) sensor (version 1)
    • Removing the temperature sensor
    • Installing the temperature sensor
    • Function test
  • Replacing engine coolant temperature (ECT) sensor (Version 2)
    • Replacing temperature sensor
      • Removing temperature sensor
      • Installing temperature sensor
    • Follow-up work
      • Function test
  • Replacing radiator/charge air cooler (CAC)
    • Notes
    • Removing radiator assembly
    • Replacing water cooler/charge air cooler (CAC)
    • Installing cooler unit
    • Installing engine coolant fan (FC)
    • Fill coolant
  • Radiator / charge air cooler (CAC), replacement
    • Notes
    • Removal
      • Removing the radiator unit
      • Work under the car
      • Drain the coolant
      • Work from above
    • Installation
      • Installing the radiator and charge air cooler (CAC)
      • Work from above
      • Installing the engine cooling fan (FC)
      • Topping up the coolant
• Fuel
  • Replacing the throttle body (TB)
    • Removing the throttle body (TB)
    • Installing the throttle body (TB)
  • Replacing the fuel filter
    • Removal
      • Draining the fuel system
      • Removing the fuel filter
    • Installation
      • Installing the fuel filter
  • Right side fuel pump with level sensor
    • Removal
      • Preparation
      • Right side fuel pump with level sensor
      • Level sensor with cable and pipe system
    • Installation
      • Level sensor with cable and pipe system
      • Right side fuel pump with level sensor
  • Pressure sensor, fuel tank, replacing
    • Removal
      • Removing the pressure sensor
    • Installation
      • Installation
  • Reading off the test results / the fuel tank values
    • Key for interpreting the results of the read off
    • Information
  • Replacing the right-hand level sensor and pump
    • Removal
      • Notes
      • Depressurizing the fuel system
      • Draining fuel tank
      • Removing the left-hand level sensor
      • Removing the right-hand level sensor / pump
      • Removing the right-hand level sensor
    • Installation
      • Installing the right-hand level sensor
      • Installing the right-hand level sensor and pump and the left-hand level sensor in the fuel tank
      • Cable routing when replacing the fuel tank
      • Finishing