Specifications Index
INTEGRA SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM GENERAL SERVICING | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 134 ft. lb (181 N.m) | ||
| Rear | 136 ft. lb (185 N.m) | ||
| Battery | See "BATTERY SPECIFICATIONS" table under CAPACITIES | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | ON-VEHICLE TESTING | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | DRIVE BELT ADJUSTMENTS | ||
| Drive Belt Routing | DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 13.5-18 psi | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | |||
| 1.8L VTEC | WATER PUMP | ||
| 1.8L Except VTEC | WATER PUMP | ||
| Engine Mechanical | |||
| 1.8L VTEC | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | Minimum oil pressure with engine at idle should be 10 psi (0.7 kg/cm2
). Minimum oil pressure at 3000 RPM should be 50 psi (3.5 kg/cm2 ). |
||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | A/T 55 ft. lb (75 N.m) M/T 77 ft. lb (105 N.m) |
||
| 1.8L Except VTEC | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | Minimum oil pressure with engine at idle should be 10 psi (0.7 kg/cm2
). Minimum oil pressure at 3000 RPM should be 50 psi (3.5 kg/cm2 ). |
||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | A/T 55 ft. lb (75 N.m) M/T 77 ft. lb (105 N.m) |
||
| Fuel System | |||
| Pressure Specification | |||
| W/O Vacuum | GS-R 48-55 psi (3.4-3.9kg/cm2
) Except GS-R 40-47 psi (2.8-3.3kg/cm2 ) |
||
| W/ Vacuum | GS-R 40-47 psi (2.8-3.3kg/cm2
) Except GS-R 31-36 psi (2.2-2.5kg/cm2 ) |
||
| Fuel Pressure Test Procedure | FUEL PRESSURE | ||
| Fuel Filter Location | |||
| Fuel Filter R & I | |||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & TIMING MARKS | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | N/A | ||
| Spark Plug | |||
| GS-R | |||
| NGK PFR6G-13 Nippondenso PK20PR-L13 |
|||
| Except GS-R | |||
| NGK ZFR5F-11 or ZRF6F-11 (Hot Climates) Nippondenso KJ16CR-L11 or KJ20CR-L11 (Hot Climates) |
|||
| Gap | .043 In. (1.1 mm) | ||
| Torque | 13 ft. lb (18 N.m) | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 80 ft. lb (104 N.m) | ||